Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type with Single Knob Type) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _061290 NAVIGATION / MULTI INFO DISPLAY _0522654 NAVIGATION SYSTEM(for Radio and Display Type with Single Knob Type) D

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type with Single Knob Type)  DIAGNOSIS SYSTEM  


CHECK FOR DTCs (USING SYSTEM CHECK MODE SCREEN)


HINT:

When system self-diagnosis DTCs cannot be output due to a malfunction that is preventing diagnosis mode from being started or the multi-display from displaying, read the DTCs using the GTS.


a.

Start diagnosis and display the "Service Menu" screen.


b.

Select "Failure Diagnosis" on the service menu screen to display the failure diagnosis screen.


c.
E483323E01
0.625,1.229 0.625,0.667 true 1,1.24 1,0.677 true 2.479,1.729 2.479,0.677 true 1.708,2.625 1.708,2.333 true 2.604,2.646 2.604,2.354 true 0.552,0.479 0.76,0.667 0.208,0.188 10 false *a 0.917,0.479 1.135,0.677 0.219,0.198 10 false *b 1.656,2.635 1.896,2.823 0.24,0.188 10 false *d 2.542,2.656 2.75,2.833 0.208,0.177 10 false *e 2.396,0.49 2.583,0.688 0.188,0.198 10 false *c

Select "System Check" of the failure diagnosis screen to display the system check mode screen.

System Check Mode Screen Description
Display Content
*a: Device Name List Displays the components names, including additional devices (the physical address is displayed if the name is unknown)
*b: Check Result Displays the inspection result of connected devices
*c: Optional Device Name List Displays the components names, including aftermarket devices
*d: Memory Clear Delete current DTCs and confirmed DTCs (press and hold for 3 seconds or more)
*e: Recheck Performs a check again

i.

Confirm that each of the following connected devices are displayed:

Name Component Connection Method
AVN Radio and display receiver assembly -
DSP-AMP Stereo component amplifier assembly AVC-LAN
IF-BOX_USB No.1 Stereo jack adapter assembly USB
DCM Telematics Transceiver USB

HINT:
·

When diagnosis starts, the system check mode screen is displayed and the check is performed.

·

System check mode displays the inspection results screen based on the response for each device during "system inspection instruction", "system inspection result demand", etc., and "Normal Diagnosis Notice", notifications.

·

The displayed screen is an example only. The actual device name displayed on the screen may differ depending on the connected device (dealer installed options, etc.).




ii.

CHECK SYSTEM CHECK RESULTS (AVC-LAN/USB/LOCAL BUS CONNECTED DEVICES)

Check result Meaning

*1: When the "DETAIL" button is pressed, the system transitions to the unit check mode screen.

*2: If "NCON" is displayed for all AVC-LAN connected devices or all AVC-LAND connected devices are not displayed, refer to the troubleshooting procedure for AVC-LAN malfunction.

OK No DTCs are stored
DETAIL
(*1)
DTCs are stored
NCON
(*2)
·

A device that was previously registered to the system is not responding during registration

·

Cannot confirm a connection of a device that was previously registered to the system


NRES No response of diagnosis information
Device name and/or system check result cannot be displayed for AVC-LAN*2/USB/LOCAL BUS CONNECTED DEVICES No history of a device being registered to the system, and no response during the diagnosis check



d.
E483961E01
1.573,0.958 1.51,0.677 true 0.531,1.813 0.219,2.042 true 1.333,2.104 1.333,2.635 true 1.771,2.094 1.771,2.625 true 2.208,2.104 2.208,2.635 true 2.708,2.458 2.708,2.698 true 1.417,0.5 1.729,0.698 0.313,0.198 10 false *a 0.031,2 0.344,2.198 0.313,0.198 10 false *b 1.24,2.677 1.552,2.875 0.313,0.198 10 false *c 1.708,2.677 2.021,2.875 0.313,0.198 10 false *d 2.146,2.698 2.458,2.896 0.313,0.198 10 false *e 2.656,2.719 2.969,2.917 0.313,0.198 10 false *f

Unit Check Mode

i.

When "DETAIL" is displayed on the system check mode inspection results, the system transitions to the unit check mode screen when pressed.


ii.

Confirm and record the DTCs

Unit Check Mode Screen Description
Display Content
*a: Device name Target device name
*b: History DTC Displays stored DTCs (up to 6 items) for the target device
*c: Latest An "X" is displayed for the target device when latest DTCs (latest malfunction in current trip) exist
*d: Confirm An "X" is displayed for the target device when confirmed DTCs (diagnosis codes that have been confirmed up until the current time) exist
*e: Time of occurrence Displays the time that the DTC was stored
*f: Code CLR Clears DTC information of the target device and clears the display

NOTICE:

A maximum of 6 codes are stored for the radio and display receiver assembly. When it is suspected that more than 6 codes are output, confirm the DTCs using the GTS.


HINT:

Unit check mode screen is updated once per second.





CLEAR DTC (USING SYSTEM CHECK MODE SCREEN)


a.
E466834

Clear the DTCs

i.

Select "Code CLR" on the unit check mode screen (press and hold for 3 seconds or more) and clear the DTCs.




DIAGNOSTIC MODE SCREEN TRANSITION


a.

Service Menu

E475535

E469817

E469818

E466833



ENTER DIAGNOSTIC MODE


HINT:
·

When system self-diagnosis DTCs cannot be output due to a malfunction that is preventing diagnosis mode from being started or the multi-display from displaying, read the DTCs using the GTS.

·

Enter diagnostic mode by performing one of the following methods.



a.

Start method 1

i.

Using the GTS, display the diagnostic mode window.

Body Electrical > Navigation System > Utility
Tester Display
Diagnostic Mode
50005 496 2765

ii.
E466835

When diagnosis starts, the "Service Menu" screen is displayed.



b.

Start method 2

i.

Ensure that the vehicle is stopped.


ii.

Turn the ignition switch to ON.


iii.

Turn off the multi-display.


iv.

Turn off the audio of the radio and display receiver assembly.


v.
E366965

Flick the multi-display 5 times from left to right as shown in the illustration.


vi.
E366966

Flick the multi-display 5 times from right to left as shown in the illustration.

HINT:

Make sure to complete the operation within 15 seconds of performing the initial flick from left to right.



vii.
E466835

When diagnosis starts, the service menu screen is displayed.

HINT:

If diagnosis does not start due to a failed operation, turn the display on then off and perform the procedure from the start. (Only turning the audio of the radio and display receiver assembly from off to on is not a valid method)





CANCEL DIAGNOSTIC MODE


HINT:

There are 2 methods to cancel diagnosis


a.

Cancellation method 1

i.

Turn the ignition switch off.



b.

Cancellation method 2

i.

Turn off the radio and display receiver assembly.




SERVICE MENU


E466835

HINT:

The service menu screen can be used to perform malfunction diagnosis for each device, confirm functions and information, and collect data.


a.
E466836

Failure Diagnosis

Failure Diagnosis Screen Display Contents
Display Details Proceed to
System Check Display the names of devices connected to the system, and display current and confirmed DTCs as diagnosis results for those devices. (Click here)
Diagnosis Recorder "Bluetooth" connection history and Wi-Fi connection history can be confirmed -

HINT:

Each failure diagnosis screen is created by the radio and display receiver assembly.


i.
E466837

Diagnosis Recorder

Diagnosis Recorder Screen Description
Display Details Proceed to
Delete REC DATA Recorded history data can be cleared -
Recording ON/OFF When performing a "Bluetooth" trace or Wi-Fi trace, the recorder function can be set to off -
BT cmc Trace output "Bluetooth" connection history can be confirmed (Click here)
Wi-Fi cmc Trace output "Bluetooth" connection history can be confirmed

HINT:

Each diagnosis recorder screen is created by the radio and display receiver assembly.




b.
E469819

Function Check/Setting I

Function Check/Setting I Screen Description
Display Content Proceed to
Panel&Steering Switch Checks the operation of the panel switch and steering switch (Click here)
Touch Switch Check Checks the operation of the touch switch of the multi-display
Microphone Check Checks the connection status of the microphone to the radio and display receiver assembly
System Sensors Check
·

Displays GNSS related information

·

Sets GNSS date and time settings

·

Displays information regarding each sensor in the radio and display receiver assembly


DAB Reception Check Performs an inspection of DAB reception
Vehicle Signal Performs an inspection of vehicle side signal received by the radio and display receiver assembly
HF Voice Quality Setting HF Voice Quality Setting

HINT:

Each function check/setting I screen is created by the radio and display receiver assembly.



c.
E466839

Service Information

HINT:

The service information screen can be used to confirm information and read the memory.


Service Information Screen Description
Display Content Proceed to
VUI Information Displays information regarding voice recognition (Click here)
Memory point backup Performs memory read using the GTS -
Version Information Displays connected device version information -
APP distribution Info Displays in-vehicle device ID, device identification ID, distribution application PF version, registered user information, etc. -
Repro info Displays in-vehicle device ID, SCOMO ID, etc. -

HINT:

Each service information screen is created by the radio and display receiver assembly.


i.
E466861

APP distribution Info

APP distribution Info Screen Description
Item Content
in-vehicle ID Displays in-vehicle device ID
Model discernment ID Displays model discernment ID
APP distribution PF version Displays platform version that the application uses
Connection Server This item is displayed but is not used
User registration User registration information is displayed


ii.
E466840

Repro info

Repro Info Screen Display Information
Display Details
In-vehicle ID Displays in-vehicle device ID of radio and display receiver assembly
SCOMO ID This item is displayed but is not used
Server This item is displayed but is not used



d.
E466841

Product Information

Product Information Screen Description
Display Content
VIN Displays VIN
Product Number (AVN) Displays serial number of the radio and display receiver assembly
Product Number (Ext Box) This item is displayed but is not used
HU ID Displays serial number of the radio and display receiver assembly
Chip serial No. (AVN) Displays IC serial number of the radio and display receiver assembly
Chip serial No. (Ext Box) This item is displayed but is not used
DCM IMEI Displays telematics transceiver IMEI
DCM ICCID Displays telematics transceiver ICCID
DCM MSISDN Displays telematics transceiver MSISDN
DCM Contract status Displays telematics transceiver contract status
HELPNET ID Displays telematics transceiver HELPNET ID