This DTC is stored when the telematics transceiver detects an open or short in the manual (SOS) switch indicator (red) circuit of the manual (SOS) switch.
The manual (SOS) switch indicator (red) illuminates for 10 seconds and turns off when the power switch is turned to ON.
If a malfunction in the telematics system is detected, the manual (SOS) switch indicator (red) will illuminate. However, the manual (SOS) switch indicator (red) may not illuminate when this DTC is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1570 | Red LED Error | Current for the manual (SOS) switch indicator (red) exceeds malfunction threshold for 10 seconds or more when the power switch is on (IG) | ·
Telematics transceiver ·
Map light assembly (manual (SOS) switch) ·
Harness or connector |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
When replacing the telematics transceiver, make sure to replace it with a new one.
If DTC B1570 is stored, the manual (SOS) switch indicator (red) may not illuminate when another DTC is stored.
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and wait for 10 seconds.
Turn the GTS on.
Clear the DTCs.
Check for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Component with harness connected
(Map Light Assembly (Manual (SOS) Switch)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| R15-6 (IND1) - R15-1 (GND3) | 2 seconds after power switch turned to ON
→ Power switch off |
8.5 to 10 V
→ Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Assembly (Manual (SOS) Switch)) |
Remove the map light assembly (manual (SOS) switch).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for TMMT Made)>REMOVAL
Connect 2 dry-cell batteries (1.5 V each) in series.
Check map light assembly (manual (SOS) switch) illumination (red).
Apply battery voltage between the terminals of the map light assembly (manual (SOS) switch) and check the illumination (red) condition of map light assembly (manual (SOS) switch).
| Measurement | Specified Condition |
|---|---|
| Battery positive (+) → R15-6 (IND1) | Map light assembly (manual (SOS) switch) illuminates (red) |
| Battery positive (-) → R15-1 (GND3) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F165 telematics transceiver connector.
Disconnect the R15 map light assembly (manual (SOS) switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F165-11 (IND1) - R15-6 (IND1) | Always | Below 1 Ω |
| F165-11 (IND1) or R15-6 (IND1) - Body ground | Always | 10 kΩ or higher |
| F165-26 (SIG-) - R15-1 (GND3) | Always | Below 1 Ω |
| F165-26 (SIG-) or R15-1 (GND3) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT