Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall with Dual Knob Type Radio and Display) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _084041 TELEMATICS _0524446 TELEMATICS SYSTEM(for eCall with Dual Knob Type Radio and Display) C

TELEMATICS  TELEMATICS SYSTEM(for eCall with Dual Knob Type Radio and Display)  B1573  Disconnect/Short in Telephone Antenna Circuit  B15CB  Telephone Antenna Disconnected  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the No. 1 amplifier antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1573 Disconnect/Short in Telephone Antenna Circuit No. 1 amplifier antenna assembly impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the power switch is on (IG)
(Short circuit)
·

Telematics transceiver

·

No. 1 amplifier antenna assembly

·

No. 3 antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

Antenna cord sub-assembly


B15CB Telephone Antenna Disconnected No. 1 amplifier antenna assembly impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the power switch is on (IG)
(Open circuit)
·

Telematics transceiver

·

No. 1 amplifier antenna assembly

·

No. 3 antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

Antenna cord sub-assembly



WIRING DIAGRAM

E359861E03
5.646,2.198 7.104,3.188 1.458,0.99 10 false Telematics transceiver 0.083,2.073 1.552,2.5 1.469,0.427 10 false No. 1 Amplifier Antenna Assembly 4.469,2.125 4.781,2.323 0.313,0.198 10 false *1 2.146,2.125 2.458,2.323 0.313,0.198 10 false *2 5.49,1.229 5.802,1.427 0.313,0.198 10 false TA 5.49,1.667 5.802,1.865 0.313,0.198 10 false TA 1.208,1.208 1.521,1.406 0.313,0.198 10 false RA 1.208,1.667 1.521,1.865 0.313,0.198 10 false RA 3.438,1.219 3.594,1.417 0.156,0.198 10 false A 3.438,1.677 3.594,1.875 0.156,0.198 10 false A 3.073,1.219 3.229,1.417 0.156,0.198 10 false B 3.073,1.677 3.229,1.875 0.156,0.198 10 false B 5.531,1.021 5.688,1.219 0.156,0.198 10 false 1 3.448,1.031 3.604,1.229 0.156,0.198 10 false 1 3.083,1.031 3.24,1.229 0.156,0.198 10 false 1 5.5,1.469 5.813,1.667 0.313,0.198 10 false 1a 3.406,1.469 3.719,1.667 0.313,0.198 10 false 1a 3.042,1.458 3.354,1.656 0.313,0.198 10 false 1a 1.26,1.021 1.417,1.219 0.156,0.198 10 false 4 1.229,1.469 1.542,1.667 0.313,0.198 10 false 4a 5.844,1.208 6.302,1.406 0.458,0.198 10 false TEL 1.323,2.823 5.76,3.021 4.438,0.198 10 false *1: No. 6 Antenna Cord Sub-assembly 1.323,3.156 5.76,3.354 4.438,0.198 10 false *2: No. 3 Antenna Cord Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall with Dual Knob Type Radio and Display)>REGISTRATION


PROCEDURE

1.CHECK DTC
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG) and wait for 10 seconds.


d.

Turn the GTS on.


e.

f.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall with Dual Knob Type Radio and Display)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT NO. 1 AMPLIFIER ANTENNA ASSEMBLY
2.INSPECT NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Remove the No. 1 amplifier antenna assembly.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL


b.
E271865C14
1.969,1.479 2.229,1.729 false 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 2.26,1.708 2.573,1.906 0.313,0.198 10 false 4a
*a Component without harness connected
(No. 1 Amplifier Antenna Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 - 4a Always 4 to 11 kΩ



Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY

3.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E359862C02
0.354,3.375 0.76,3.646 0.406,0.271 0.323,1.177 0.729,1.448 0.406,0.271 1.875,1.479 2.333,1.479 true 1.229,3.583 1.552,3.583 true 0.125,0.125 0.438,0.323 0.313,0.198 10 false *a 0.469,1.229 0.625,1.427 0.156,0.198 10 false B 0.448,3.417 0.76,3.615 0.313,0.198 10 false RA 1.021,3.5 1.333,3.698 0.313,0.198 10 false 4a 2.375,1.406 2.688,1.604 0.313,0.198 10 false 1a 0.094,2.781 0.406,2.979 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to No. 6 Amplifier Antenna Assembly)
*b Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)


Disconnect the No. 3 antenna cord sub-assembly from the No. 1 amplifier antenna assembly connector.


b.

Disconnect the No. 3 antenna cord sub-assembly from the No. 6 antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
RA-4 - B-1 Always Below 1 Ω
RA-4a - B-1a Always Below 1 Ω
RA-4 or B-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT NO. 6 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY

4.INSPECT NO. 6 ANTENNA CORD SUB-ASSEMBLY
a.
E359863C02
0.375,1.146 0.781,1.448 0.406,0.302 0.375,3.406 0.781,3.708 0.406,0.302 1.344,2 1.656,1.49 true 1.885,1.458 2.229,1.458 true 1.917,3.74 2.26,3.74 true 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 0.5,1.219 0.813,1.417 0.313,0.198 10 false TA 0.51,3.469 0.667,3.667 0.156,0.198 10 false A 2.292,1.365 2.604,1.563 0.313,0.198 10 false 1a 2.333,3.656 2.646,3.854 0.313,0.198 10 false 1a 1.104,1.99 1.563,2.188 0.458,0.198 10 false TEL 0.156,2.792 0.469,2.99 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Telematics Transceiver)


Disconnect the No. 6 antenna cord sub-assembly from the No. 3 antenna cord sub-assembly connector.


b.

Disconnect the No. 6 antenna cord sub-assembly from the telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 - TA-1 Always Below 1 Ω
A-1a - TA-1a Always Below 1 Ω
A-1 or TA-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPLACE NO. 6 ANTENNA CORD SUB-ASSEMBLY

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT