If the telematics transceiver detects an error in communication between itself and the airbag sensor assembly as a result of a self check, this DTC will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C4 | SRS Communication Error | The telematics transceiver detects an error in signals from the airbag sensor assembly when the power switch is on (IG) | ·
Telematics transceiver ·
Airbag sensor assembly ·
Harness or connector ·
Airbag system |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
This vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When replacing the telematics transceiver, make sure to replace it with a new one.
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and wait for 10 seconds.
Turn the GTS on.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Check if airbag system DTCs are output.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| *a | Component with harness connected
(Telematics Transceiver) |
| *b | Waveform |
Check the output waveform.
Remove the telematics transceiver with the connector(s) still connected.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
Connect an oscilloscope to terminal F165-24 (GSW) - Body ground.
Turn the power switch on (IG).
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Tester connection | F165-24 (GSW) - Body ground |
| Tool setting | 5.0 V/DIV., 20 ms/DIV. |
| Vehicle condition | Power switch on (IG) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F165-24 (GSW) - Body ground | Power switch on (IG) | Pulse generation |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the F165 telematics transceiver connector.
Disconnect the F150 airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F165-24 (GSW) - F150-23 (GSW3) | Always | Below 1 Ω |
| F165-24 (GSW) or F150-23 (GSW3) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG