Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall with Dual Knob Type Radio and Display) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _084041 TELEMATICS _0524446 TELEMATICS SYSTEM(for eCall with Dual Knob Type Radio and Display) C

TELEMATICS  TELEMATICS SYSTEM(for eCall with Dual Knob Type Radio and Display)  B1AC0  Telephone Speaker Cable Connection Malfunction  


DESCRIPTION

If there is an open in a speaker circuit, the telematics transceiver detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the telematics transceiver or communication telematics box.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1AC0 Telephone Speaker Cable Connection Malfunction The malfunction is detected in the telephone speaker circuit for approximately 10 seconds or more.
·

Communication telematics box

·

Telematics transceiver

·

Harness or connector



WIRING DIAGRAM

E405969E07
4.615,2.51 6.052,3.167 1.438,0.656 10 false Telematics Transceiver 1.125,2.479 3.146,2.74 2.021,0.26 10 false Communication Telematics Box 4.604,2.333 6.406,2.875 1.802,0.542 10 false F165 4.344,1.146 5.667,2.125 1.323,0.979 10 false 20 4.615,1.25 5.938,2.229 1.323,0.979 10 false SP+ 1.75,1.25 3.073,2.229 1.323,0.979 10 false SP+ 1.813,1.688 3.135,2.667 1.323,0.979 10 false SP- 4.625,1.729 5.948,2.708 1.323,0.979 10 false SP- 4.344,1.583 5.667,2.563 1.323,0.979 10 false 21 2.167,1.135 3.49,2.115 1.323,0.979 10 false 3 2.177,1.563 3.5,2.542 1.323,0.979 10 false 8 1.115,2.281 4.177,2.479 3.063,0.198 10 false R16

CAUTION / NOTICE / HINT

NOTICE:

When replacing the telematics transceiver, make sure to replace it with a new one.


PROCEDURE

1.CHECK DTC
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG) and wait for 10 seconds.


d.

Turn the GTS on.


e.

f.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall with Dual Knob Type Radio and Display)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (COMMUNICATION TELEMATICS BOX - TELEMATICS TRANSCEIVER)
2.CHECK HARNESS AND CONNECTOR (COMMUNICATION TELEMATICS BOX - TELEMATICS TRANSCEIVER)
a.

Disconnect the R16 communication telematics box connector.


b.

Disconnect the F165 telematics transceiver connector.


c.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R16-3 (SP+) - F165-20 (SP+) Always Below 1 Ω
R16-8 (SP-) - F165-21 (SP-) Always Below 1 Ω
R16-3 (SP+) or F165-20 (SP+) - Body ground Always 10 kΩ or higher
R16-8 (SP-) or F165-21 (SP-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK COMMUNICATION TELEMATICS BOX

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK COMMUNICATION TELEMATICS BOX
a.

Replace the communication telematics box.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall with Dual Knob Type Radio and Display)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall with Dual Knob Type Radio and Display)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (FRONT NO. 4 SPEAKER ASSEMBLY IS DEFECTIVE)

NG

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT