Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall with Dual Knob Type Radio and Display) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _084041 TELEMATICS _0524446 TELEMATICS SYSTEM(for eCall with Dual Knob Type Radio and Display) J

TELEMATICS  TELEMATICS SYSTEM(for eCall with Dual Knob Type Radio and Display)  Emergency Call Switch Illumination Circuit  


WIRING DIAGRAM

E354798E13
1.094,2.104 1.552,2.302 0.458,0.198 10 false R15 1.083,2.26 3.104,2.667 2.021,0.406 10 false Map Light Assembly 4.677,2.063 5.417,2.26 0.74,0.198 10 false F165 4.688,2.25 6.979,2.646 2.292,0.396 10 false Telematics Transceiver 2.521,0.594 3.135,0.792 0.615,0.198 10 false RRID 2.438,1.167 3.052,1.365 0.615,0.198 10 false GND3 5.177,0.729 5.792,0.927 0.615,0.198 10 false SLED 5.198,1.156 5.813,1.354 0.615,0.198 10 false SIG- 2.969,0.594 3.156,0.792 0.188,0.198 10 false 7 4.948,0.594 5.104,0.792 0.156,0.198 10 false 9 2.948,1.125 3.125,1.313 0.177,0.188 10 false 1 4.906,1.146 5.24,1.313 0.333,0.167 10 false 26 1,1.646 3.208,1.969 2.208,0.323 10 false Manual (SOS) Switch

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall with Dual Knob Type Radio and Display)>REGISTRATION

·

When replacing the telematics transceiver, make sure to replace it with a new one.



PROCEDURE

1.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)
a.
B129570C94
1.167,1.813 1.406,1.083 true 2.906,1.75 2.646,1.115 true 0.073,0.094 0.354,0.333 0.281,0.24 10 false *a 2.792,1.813 3.313,2.031 0.521,0.219 10 false GND3 1.01,1.865 1.448,2.073 0.438,0.208 10 false RRID
*a Component without harness connected
(Map Light Assembly (Manual (SOS) Switch))


Remove the map light assembly (manual (SOS) switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for TMMT Made)>REMOVAL


b.

Connect 4 dry-cell batteries (1.5 V each) in series.


c.

Check map light assembly (manual (SOS) switch) illumination.

i.

Apply battery voltage between the terminals of the map light assembly (manual (SOS) switch) and check the illumination condition of map light assembly (manual (SOS) switch).

OK:
Measurement Condition Specified Condition
Battery positive (+) → R15-7 (RRID) Map light assembly (manual (SOS) switch)
Battery positive (-) → R15-1 (GND3)




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT SASSEMBLY (MANUAL (SOS) SWITCH))

NG

REPLACE MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)

2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT SASSEMBLY (MANUAL (SOS) SWITCH))
a.

Disconnect the F165 telematics transceiver connector.


b.

Disconnect the R15 map light assembly (manual (SOS) switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F165-9 (SLED) - R15-7 (RRID) Always Below 1 Ω
F165-26 (SIG-) - R15-1 (GND3) Always Below 1 Ω
F165-9 (SLED) or R15-7 (RRID) - Body ground Always 10 kΩ or higher
F165-26 (SIG-) or R15-1 (GND3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR