Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall with Single Knob Type Radio and Display) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _084041 TELEMATICS _0524469 TELEMATICS SYSTEM(for eCall with Single Knob Type Radio and Display) C

TELEMATICS  TELEMATICS SYSTEM(for eCall with Single Knob Type Radio and Display)  B15C511  Emergency Call Switch Circuit Short to Ground  B15C513  Emergency Call Switch Circuit Open  


DESCRIPTION

If the telephone transceiver assembly detects an error in the communication between the telephone transceiver assembly and the map light assembly (mayday switch assembly) as a result of the telephone transceiver assembly self check, this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C511 Emergency Call Switch Circuit Short to Ground Mayday switch assembly impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Map light assembly

·

Harness or connector

·

Telephone transceiver assembly


B15C513 Emergency Call Switch Circuit Open Mayday switch assembly impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Map light assembly

·

Harness or connector

·

Telephone transceiver assembly



WIRING DIAGRAM

E484670E04
0.573,2.073 0.969,2.26 0.396,0.188 10 false F175 5.302,2.083 5.698,2.271 0.396,0.188 10 false R15 0.573,2.24 1.958,2.656 1.385,0.417 10 false Telephone Transceiver Assembly 5.302,2.229 7.042,2.521 1.74,0.292 10 false Map Light Assembly 5.375,0.771 5.771,0.958 0.396,0.188 10 false SIG1 5.396,1.563 5.823,1.75 0.427,0.188 10 false GND3 1.438,0.792 1.833,0.979 0.396,0.188 10 false SIG1 1.448,1.594 1.802,1.781 0.354,0.188 10 false SIG- 1.844,0.698 2.094,0.885 0.25,0.188 10 false 21 1.844,1.479 2.094,1.667 0.25,0.188 10 false 3 5.208,0.667 5.417,0.854 0.208,0.188 10 false 8 5.135,1.479 5.344,1.667 0.208,0.188 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall with Single Knob Type Radio and Display)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.

·

Before replacing the telephone transceiver assembly, refer to Service Bulletin.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

b.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Telematics > Trouble Codes
50001 459

Result:
Result Proceed to
No DTCs are output. A
DTCs are output. B



A

B

2.INSPECT MAP LAMP ASSEMBLY
2.INSPECT MAP LAMP ASSEMBLY
a.
B641819C05
2.438,1.813 2.573,1.115 true 1.75,1.896 1.302,1.083 true 0.073,0.094 0.354,0.333 0.281,0.24 10 false *a 1.792,1.802 2.354,2.052 0.563,0.25 10 false SIG1 2.479,1.792 3.042,2.042 0.563,0.25 10 false GND3
*a Component without harness connected
(Map Light Assembly)


Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for TMMT Made)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (SIG1) - 1 (GND3) Mayday switch assembly not operated 407 to 416 Ω
8 (SIG1) - 1 (GND3) Mayday switch assembly operated 81 to 83 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the F175 telephone transceiver assembly connector.


b.

Disconnect the R15 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F175-21 (SIG1) - R15-8 (SIG1) Always Below 1 Ω
F175-3 (SIG-) - R15-1 (GND3) Always Below 1 Ω
F175-21 (SIG1) or R15-8 (SIG1) - Body ground Always 10 kΩ or higher
F175-3 (SIG-) or R15-1 (GND3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT