Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall with Single Knob Type Radio and Display) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _084041 TELEMATICS _0524469 TELEMATICS SYSTEM(for eCall with Single Knob Type Radio and Display) J

TELEMATICS  TELEMATICS SYSTEM(for eCall with Single Knob Type Radio and Display)  Emergency Call Switch Illumination Circuit  


WIRING DIAGRAM

E484671E06
2.469,2.24 2.938,2.406 0.469,0.167 10 false F175 2.469,2.396 3.833,2.76 1.365,0.365 10 false Telephone Transceiver Assembly 4.563,2.615 4.938,2.823 0.375,0.208 10 false R15 4.552,2.781 6.542,3.167 1.99,0.385 10 false Map Light Assembly 4.24,0.896 4.5,1.115 0.26,0.219 10 false 7 4.219,1.698 4.531,1.938 0.313,0.24 10 false 1 4.458,0.906 4.844,1.083 0.385,0.177 10 false RRID 1.083,1 2.563,1.25 1.479,0.25 10 false from IG1 NO. 1 Relay 4.458,1.719 4.927,1.896 0.469,0.177 10 false GND3 4.969,2.135 6.74,2.313 1.771,0.177 10 false Mayday Switch Assembly 2.823,1.198 3.938,1.396 1.115,0.198 10 false ECU-IG1 NO. 1 3.292,1.823 3.76,2 0.469,0.177 10 false SIG- 3.708,1.708 4.021,1.948 0.313,0.24 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall with Single Knob Type Radio and Display)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.

·

Before replacing the telephone transceiver assembly, refer to Service Bulletin.



HINT:

Inspect the fuses and relays related to this system before inspecting the suspected areas below.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY POWER SOURCE)
a.

Disconnect the F175 telephone transceiver assembly connector.


b.

Disconnect the R15 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F175-3 (SIG-) - R15-1 (GND3) Always Below 1 Ω
F175-3 (SIG-) or R15-1 (GND3) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R15-7 (RRID) - Body Ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT MAP LIGHT ASSEMBLY

b.

Connect 4 1.5 V dry-cell batteries in series.


c.
B641819C06
0.99,1.781 1.396,1.104 true 2.219,1.771 2.573,1.104 true 0.563,1.771 1.177,1.969 0.615,0.198 10 false RRID 1.833,1.802 2.448,2 0.615,0.198 10 false GND3 0.146,0.073 0.438,0.271 0.292,0.198 10 false *a
*a Component without harness connected
(Map Light Assembly)


Connect a positive (+) lead from the batteries to terminal 7 (RRID), and a negative (-) lead to terminal 1 (GND3) of the map light assembly connector.


d.

Check if the mayday switch assembly illumination comes on.

OK:

The mayday switch assembly illumination comes on.



Result:
Proceed to
OK
NG



OK

3.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

3.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT