Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall with Single Knob Type Radio and Display) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _084041 TELEMATICS _0524469 TELEMATICS SYSTEM(for eCall with Single Knob Type Radio and Display) C

TELEMATICS  TELEMATICS SYSTEM(for eCall with Single Knob Type Radio and Display)  B157011  Indicator (Red) Circuit Short to Ground  B157013  Indicator (Red) Circuit Open  


DESCRIPTION

This DTC is stored when the telephone transceiver assembly detects an open or short in the mayday switch assembly indicator (red) circuit of the mayday switch assembly.

The mayday switch assembly indicator (red) illuminates for 5 seconds and turns off when the ignition switch is turned to ON.

If a malfunction in the telematics system is detected, the mayday switch assembly indicator (red) will blink. However, the mayday switch assembly indicator (red) may not illuminate when this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B157011 Indicator (Red) Circuit Short to Ground Mayday switch assembly indicator (red) impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Telephone transceiver assembly

·

Map light assembly (mayday switch assembly)

·

Harness or connector


B157013 Indicator (Red) Circuit Open Mayday switch assembly indicator (red) impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Telephone transceiver assembly

·

Map light assembly (mayday switch assembly)

·

Harness or connector



WIRING DIAGRAM

E484662E10
1.896,1.021 2.354,1.219 0.458,0.198 10 false RED 3.406,0.656 3.625,0.854 0.219,0.198 10 false 6 3.406,1.073 3.719,1.313 0.313,0.24 10 false 1 3,0.656 3.615,0.854 0.615,0.198 10 false IND1 2.938,1.073 3.552,1.271 0.615,0.198 10 false GND3 1.25,1.729 1.708,1.927 0.458,0.198 10 false R15 1.24,1.906 3.552,2.365 2.313,0.458 10 false Map Light Assembly (Mayday Switch Assembly) 4.979,0.667 5.292,0.865 0.313,0.198 10 false 4 4.969,1.073 5.281,1.271 0.313,0.198 10 false 3 5.167,0.781 5.781,0.979 0.615,0.198 10 false IND1 5.167,1.073 5.781,1.271 0.615,0.198 10 false SIG- 5.094,1.708 5.552,1.906 0.458,0.198 10 false F175 5.083,1.896 6.479,2.26 1.396,0.365 10 false Telephone Transceiver Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall with Single Knob Type Radio and Display)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.

·

Before replacing the telephone transceiver assembly, refer to Service Bulletin.



HINT:

If DTC B157011 or B157013 is stored, the mayday switch assembly indicator (red) may not illuminate when another DTC is stored.


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

c.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK MAP LIGHT ASSEMBLY (MAYDAY SWITCH ASSEMBLY) (INPUT VOLTAGE)
2.CHECK MAP LIGHT ASSEMBLY (MAYDAY SWITCH ASSEMBLY) (INPUT VOLTAGE)
a.
B234642C82
1.51,0.063 1.948,0.323 0.438,0.26 2.292,1.115 2.844,1.677 true 1.615,1.115 0.833,1.677 true 0.115,0.094 0.417,0.417 0.302,0.323 10 false *a 2.688,1.771 3.229,2 0.542,0.229 10 false GND3 0.625,1.688 1.031,1.854 0.406,0.167 10 false IND1 1.615,0.094 1.969,0.281 0.354,0.188 10 false R15
*a Component with harness connected
(Map Light Assembly [Mayday Switch Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R15-6 (IND1) - R15-1 (GND3) 2 seconds after ignition switch turned to ON
→ Ignition switch off
8.5 to 10 V
→ Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY (MAYDAY SWITCH ASSEMBLY) (RED INDICATOR)

NG

4.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY [MAYDAY SWITCH ASSEMBLY])
3.INSPECT MAP LIGHT ASSEMBLY (MAYDAY SWITCH ASSEMBLY) (RED INDICATOR)
a.
B641818C02
0.406,1.771 1.594,1.094 true 2.969,1.74 2.573,1.094 true 0.073,0.094 0.354,0.333 0.281,0.24 10 false *a 2.802,1.792 3.323,2.01 0.521,0.219 10 false GND3 0.24,1.76 0.677,1.969 0.438,0.208 10 false IND1
*a Component without harness connected
(Map Light Assembly [Mayday Switch Assembly])


Remove the map light assembly (mayday switch assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for TMMT Made)>REMOVAL


b.

Connect 2 dry-cell batteries (1.5 V each) in series.


c.

Connect a positive (+) lead from the batteries to terminal 6 (IND1) and a negative (-) lead to terminal 1 (GND3) of the map light assembly (mayday switch assembly) connector.


d.

Check if the mayday switch assembly indicator (red) illuminates.

OK:

Myday switch assembly indicator (red) illuminates.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY [MAYDAY SWITCH ASSEMBLY])

NG

REPLACE MAP LIGHT ASSEMBLY (MAYDAY SWITCH ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY [MAYDAY SWITCH ASSEMBLY])
a.

Disconnect the F175 telephone transceiver assembly connector.


b.

Disconnect the R15 map light assembly (mayday switch assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F175-4 (IND1) - R15-6 (IND1) Always Below 1 Ω
F175-4 (IND1) or R15-6 (IND1) - Body ground Always 10 kΩ or higher
F175-3 (SIG-) - R15-1 (GND3) Always Below 1 Ω
F175-3 (SIG-) or R15-1 (GND3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT