Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall with Single Knob Type Radio and Display) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _084041 TELEMATICS _0524469 TELEMATICS SYSTEM(for eCall with Single Knob Type Radio and Display) C

TELEMATICS  TELEMATICS SYSTEM(for eCall with Single Knob Type Radio and Display)  B157213  Microphone Circuit Open  


DESCRIPTION

This DTC is stored when a communication telematics box line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B157213 Microphone Circuit Open Current at terminal MCVD is lower than the malfunction threshold for 10 seconds or more while the ignition switch is ON
·

Telephone transceiver assembly

·

Communication telematics box

·

Mayday wire

·

Harness or connector



WIRING DIAGRAM

E405960E27
0.906,1.406 1.521,1.604 0.615,0.198 10 false MCMD 1.052,1.813 1.667,2.01 0.615,0.198 10 false SP+ 1.063,2.219 1.677,2.417 0.615,0.198 10 false SP- 0.99,2.594 1.604,2.792 0.615,0.198 10 false MICV 0.938,3.375 1.552,3.573 0.615,0.198 10 false MIC1+ 0.917,2.958 1.531,3.156 0.615,0.198 10 false MIC2+ 1.042,3.792 1.656,3.99 0.615,0.198 10 false MCI- 5.667,1.396 6.281,1.594 0.615,0.198 10 false MCMD 5.667,1.781 6.281,1.979 0.615,0.198 10 false SP+ 5.667,2.198 6.281,2.396 0.615,0.198 10 false SP- 5.656,2.583 6.271,2.781 0.615,0.198 10 false MICV 5.646,3 6.26,3.198 0.615,0.198 10 false MCI+ 5.656,3.354 6.271,3.552 0.615,0.198 10 false MCVD 5.656,3.771 6.271,3.969 0.615,0.198 10 false MCI- 5.531,4.792 6.958,5.271 1.427,0.479 10 false Telephone Transceiver Assembly 4.031,3.99 4.688,4.219 0.656,0.229 10 false * 0.375,4.75 1.438,5.156 1.063,0.406 10 false Communication Telematics Box 0.375,4.583 1.146,4.99 0.771,0.406 10 false P 2.104,1.302 2.719,1.5 0.615,0.198 10 false MCMD 2.26,1.698 2.875,1.896 0.615,0.198 10 false SP+ 2.302,2.104 2.917,2.302 0.615,0.198 10 false SP- 2.198,2.479 2.813,2.677 0.615,0.198 10 false MICV 2.135,3.281 2.75,3.479 0.615,0.198 10 false MCVD 2.219,2.906 2.833,3.104 0.615,0.198 10 false MCI+ 2.229,3.677 2.844,3.875 0.615,0.198 10 false MCI- 1.458,1.313 2.073,1.51 0.615,0.198 10 false 1 1.479,1.708 2.094,1.906 0.615,0.198 10 false 3 1.469,2.104 2.083,2.302 0.615,0.198 10 false 8 1.479,2.5 2.094,2.698 0.615,0.198 10 false 5 1.5,3.292 2.115,3.49 0.615,0.198 10 false 2 1.5,2.896 2.115,3.094 0.615,0.198 10 false 7 1.49,3.677 2.104,3.875 0.615,0.198 10 false 4 2.76,1.219 3.375,1.417 0.615,0.198 10 false 1 2.771,1.604 3.385,1.802 0.615,0.198 10 false 3 2.781,2 3.396,2.198 0.615,0.198 10 false 8 2.792,2.406 3.406,2.604 0.615,0.198 10 false 5 2.771,3.188 3.385,3.385 0.615,0.198 10 false 2 2.781,2.792 3.396,2.99 0.615,0.198 10 false 7 2.781,3.594 3.396,3.792 0.615,0.198 10 false 4 5.344,1.677 5.958,1.875 0.615,0.198 10 false 18 5.385,1.292 6,1.49 0.615,0.198 10 false 8 5.354,2.073 5.969,2.271 0.615,0.198 10 false 34 5.354,2.458 5.969,2.656 0.615,0.198 10 false 24 5.396,2.865 6.021,3.063 0.625,0.198 10 false 6 5.396,3.656 6.021,3.854 0.625,0.198 10 false 7 5.531,4.604 6.302,5.01 0.771,0.406 10 false F175 2.698,1.396 3.469,1.802 0.771,0.406 10 false R16 5.646,4.198 6.26,4.396 0.615,0.198 10 false SGND 5.354,4.083 5.979,4.281 0.625,0.198 10 false 23 1.667,4.615 2.781,5.094 1.115,0.479 10 false Mayday Wire 5.396,3.26 6.021,3.458 0.625,0.198 10 false 5 0.344,5.458 2.521,5.781 2.177,0.323 10 false *: Shielded 2.708,1.802 3.479,2.208 0.771,0.406 10 false R16 2.688,2.188 3.458,2.594 0.771,0.406 10 false R16 2.708,2.594 3.479,3 0.771,0.406 10 false R16 2.708,2.969 3.479,3.375 0.771,0.406 10 false R16 2.698,3.385 3.469,3.792 0.771,0.406 10 false R16 2.708,3.781 3.479,4.188 0.771,0.406 10 false R16

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall with Single Knob Type Radio and Display)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.

·

Before replacing the telephone transceiver assembly, refer to Service Bulletin.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

c.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAYDAY WIRE)
2.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAYDAY WIRE)
a.

Disconnect the F175 telephone transceiver assembly connector.


b.

Disconnect the R16 mayday wire connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F175-8 (MCMD) - R16-1 (MCMD) Always Below 1 Ω
F175-18 (SP+) - R16-3 (SP+) Always Below 1 Ω
F175-34 (SP-) - R16-8 (SP-) Always Below 1 Ω
F175-24 (MICV) - R16-5 (MICV) Always Below 1 Ω
F175-6 (MCI+) - R16-7 (MCI+) Always Below 1 Ω
F175-5 (MCVD) - R16-2 (MCVD) Always Below 1 Ω
F175-7 (MCI-) - R16-4 (MCI-) Always Below 1 Ω
F175-8 (MCMD) or R16-1 (MCMD) - Body ground Always 10 kΩ or higher
F175-18 (SP+) or R16-3 (SP+) - Body ground Always 10 kΩ or higher
F175-34 (SP-) or R16-8 (SP-) - Body ground Always 10 kΩ or higher
F175-24 (MICV) or R16-5 (MICV) - Body ground Always 10 kΩ or higher
F175-6 (MCI+) or R16-7 (MCI+) - Body ground Always 10 kΩ or higher
F175-5 (MCVD) or R16-2 (MCVD) - Body ground Always 10 kΩ or higher
F175-7 (MCI-) or R16-4 (MCI-) - Body ground Always 10 kΩ or higher
F175-23 (SGND) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

3.INSPECT MAYDAY WIRE (COMMUNICATION TELEMATICS BOX - WIRE HARNESS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAYDAY WIRE (COMMUNICATION TELEMATICS BOX - WIRE HARNESS)
a.
E487906C01
1.49,2.823 1.865,3.083 0.375,0.26 1.521,0.365 1.896,0.625 0.375,0.26 2.115,1.396 2.583,1.396 true 1.313,3.208 1.708,3.729 true 1.938,1.333 2.583,0.917 true 1.76,1.677 2.5,2.083 true 0.906,1.396 1.333,1.396 true 1.521,1.688 0.917,2 true 1.49,1.333 0.917,1 true 1,3.396 1.49,3.729 true 0.917,3.771 1.302,3.771 true 1.719,4 1.854,4.365 true 2.25,3.292 1.917,3.719 true 1.313,4.333 1.531,3.979 true 2.5,3.76 2.073,3.76 true 1.667,1.333 0.917,0.667 true 0.365,2.635 0.677,2.833 0.313,0.198 10 false *b 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.646,2.865 1.958,3.063 0.313,0.198 10 false P 1.594,0.406 1.906,0.604 0.313,0.198 10 false R16 0.385,1.302 0.969,1.469 0.583,0.167 10 false MCMD 0.448,3.688 1.031,4.063 0.583,0.375 10 false MCMD 0.563,0.563 1.146,0.938 0.583,0.375 10 false SP+ 2.563,2.063 3.146,2.438 0.583,0.375 10 false SP- 2.667,1.333 3.25,1.708 0.583,0.375 10 false MICV 0.49,1.927 1.073,2.302 0.583,0.375 10 false MCI+ 1.063,3.063 1.646,3.438 0.583,0.375 10 false SP+ 0.563,3.313 1.146,3.688 0.583,0.375 10 false MIC1+ 1.896,4.323 2.531,4.656 0.635,0.333 10 false SP- 2.542,3.698 3.125,4.073 0.583,0.375 10 false MICV 0.927,4.313 1.427,4.667 0.5,0.354 10 false MIC2+ 2.229,3.135 2.813,3.51 0.583,0.375 10 false MCI- 0.438,0.896 1.021,1.063 0.583,0.167 10 false MCVD 2.656,0.833 3.24,1.208 0.583,0.375 10 false MCI-
*a Component without harness connected
(Wire Harness)
*b Component without harness connected
(Communication Telematics Box)


Disconnect the R16 wire harness connector.


b.

Disconnect the P communication telematics box connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R16-1 (MCMD) - P-1 (MCMD) Always Below 1 Ω
R16-3 (SP+) - P-3 (SP+) Always Below 1 Ω
R16-8 (SP-) - P-8 (SP-) Always Below 1 Ω
R16-5 (MICV) - P-5 (MICV) Always Below 1 Ω
R16-7 (MCI+) - P-7 (MIC2+) Always Below 1 Ω
R16-2 (MCVD) - P-2 (MIC1+) Always Below 1 Ω
R16-4 (MCI-) - P-4 (MCI-) Always Below 1 Ω
R16-1 (MCMD) or P-1 (MCMD) - Body ground Always 10 kΩ or higher
R16-3 (SP+) or P-3 (SP+) - Body ground Always 10 kΩ or higher
R16-8 (SP-) or P-8 (SP-) - Body ground Always 10 kΩ or higher
R16-5 (MICV) or P-5 (MICV) - Body ground Always 10 kΩ or higher
R16-7 (MCI+) or P-7 (MIC2+) - Body ground Always 10 kΩ or higher
R16-2 (MCVD) or P-2 (MIC1+) - Body ground Always 10 kΩ or higher
R16-4 (MCI-) or P-4 (MCI-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

4.CHECK TELEPHONE TRANSCEIVER ASSEMBLY

NG

4.CHECK TELEPHONE TRANSCEIVER ASSEMBLY
a.
E442560C29
1.385,0.573 1.958,0.885 0.573,0.313 2.26,1.948 2.458,2.74 2.458,2.74 2.625,2.74 true 2.292,1.813 2.563,0.969 2.563,0.969 2.729,0.969 true 0.25,0.302 0.563,0.5 0.313,0.198 10 false *a 1.531,0.646 2.073,0.865 0.542,0.219 10 false F175 2.802,0.896 3.344,1.115 0.542,0.219 10 false MCI- 2.677,2.667 3.219,2.885 0.542,0.219 10 false MICV
*a Component with harness connected
(Telephone Transceiver Assembly)


Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F175-24 (MICV) - Body ground Ignition switch ON 7.5 to 8.5 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F175-7 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.REPLACE COMMUNICATION TELEMATICS BOX

NG

6.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
5.REPLACE COMMUNICATION TELEMATICS BOX
a.

Replace the communication telematics box with a new or known good one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>COMMUNICATION TELEMATICS BOX>REMOVAL



b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B




A

END (COMMUNICATION TELEMATICS BOX IS DEFECTIVE)

B

6.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
6.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT