Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall with Single Knob Type Radio and Display) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _084041 TELEMATICS _0524469 TELEMATICS SYSTEM(for eCall with Single Knob Type Radio and Display) C

TELEMATICS  TELEMATICS SYSTEM(for eCall with Single Knob Type Radio and Display)  B15C464  Airbag Signal Signal Plausibility Failure  


DESCRIPTION

If the telephone transceiver assembly detects an error in communication between the telephone transceiver assembly and the airbag sensor assembly as a result of the telephone transceiver assembly self check, this DTC will be output.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C464 Airbag Signal Signal Plausibility Failure Telephone transceiver assembly detects an error in signals from airbag sensor assembly when ignition switch is ON.
·

Airbag system

·

Harness or connector

·

Airbag sensor assembly

·

Telephone transceiver assembly



WIRING DIAGRAM

B641197E05
2.531,1.125 2.833,1.302 0.302,0.177 10 false 23 1.958,1.125 2.479,1.323 0.521,0.198 10 false GSW3 4.896,1.125 5.406,1.313 0.51,0.188 10 false GSW 4.604,1.125 4.875,1.333 0.271,0.208 10 false 13 1.167,2.073 1.531,2.25 0.365,0.177 10 false F150 1.156,2.24 2.74,2.458 1.583,0.219 10 false Airbag Sensor Assembly 4.667,2.063 5.219,2.292 0.552,0.229 10 false F175 4.667,2.229 6.771,2.438 2.104,0.208 10 false Telephone Transceiver Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click here

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall with Single Knob Type Radio and Display)>PRECAUTION

·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.

·

Before replacing the telephone transceiver assembly, refer to Service Bulletin.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK DTC (AIRBAG SYSTEM)
a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Check the DTC of "AIRBAG SYSTEM".


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK DTC

B

2.CHECK DTC
a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK TELEPHONE TRANSCEIVER ASSEMBLY (GSW SIGNAL)
3.CHECK TELEPHONE TRANSCEIVER ASSEMBLY (GSW SIGNAL)
a.
E487324C01
1.469,0.219 1.948,0.458 0.479,0.24 0.719,0.375 0.896,0.375 0.896,0.375 1.104,1.104 true 0.135,0.104 0.406,0.365 0.271,0.26 10 false *a 0.323,0.292 0.698,0.438 0.375,0.146 10 false GSW 1.563,0.25 2,0.5 0.438,0.25 10 false F175 0.208,4.031 0.646,4.292 0.438,0.26 10 false GND
*a Component with harness connected
(Telephone Transceiver Assembly)


Remove the telephone transceiver assembly but do not disconnect the connectors.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Check the input waveform.

i.

Check the signal waveform according to the condition(s) in the table below. (Check the waveform from the back of the wire harness connector of the telephone transceiver assembly while the airbag sensor assembly connectors are connected.)

Reference Waveform:
Item Condition
Tester connection F175-13 (GSW) - Body ground
Tool setting 5.0 V/DIV., 20 ms./DIV.
Vehicle condition Ignition switch ON


OK:

The waveform is similar to that shown in the illustration.




Result:
Proceed to
OK
NG



OK

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - AIRBAG SENSOR ASSEMBLY)
4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the F175 telephone transceiver assembly connector.


b.

Disconnect the F150 airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F175-13 (GSW) - F150-23 (GSW3) Always Below 1 Ω
F175-13 (GSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR