Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall with Single Knob Type Radio and Display) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _084041 TELEMATICS _0524469 TELEMATICS SYSTEM(for eCall with Single Knob Type Radio and Display) C

TELEMATICS  TELEMATICS SYSTEM(for eCall with Single Knob Type Radio and Display)  B15DE87  Telematics Transceiver Location Data Missing Message  


DESCRIPTION

The telephone transceiver assembly checks the reception condition of the location data every minute after the ignition switch is turned to ON. If the location data is not received from the radio and display receiver assembly, this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15DE87 Telematics Transceiver Location Data Missing Message Location information from USB communication is interrupted
·

Harness or connector

·

Telephone transceiver assembly

·

Radio and display receiver assembly



WIRING DIAGRAM

E418547E18
1.823,0.823 2.302,1.031 0.479,0.208 10 false USB- 1.792,1.625 2.271,1.833 0.479,0.208 10 false USBS 1.802,1.219 2.281,1.427 0.479,0.208 10 false USB+ 2.375,0.646 2.563,0.854 0.188,0.208 10 false 2 2.385,1.052 2.573,1.26 0.188,0.208 10 false 1 2.385,1.448 2.573,1.656 0.188,0.208 10 false 3 4.625,1.844 4.885,2.052 0.26,0.208 10 false 15 2.333,2.229 2.594,2.438 0.26,0.208 10 false 17 0.844,3.417 4.177,3.635 3.333,0.219 10 false : USB Communication Line 4.948,2.896 6.344,3.292 1.396,0.396 10 false Telephone Transceiver Assembly 1.781,2.01 2.26,2.208 0.479,0.198 10 false USBV 1.781,2.417 2.26,2.615 0.479,0.198 10 false USBG 4.969,2.042 5.448,2.24 0.479,0.198 10 false USBV 4.969,2.427 5.448,2.625 0.479,0.198 10 false USBG 2.354,0.823 2.729,1.063 0.375,0.24 10 false j16 4.635,2.24 4.896,2.448 0.26,0.208 10 false 31 2.323,1.833 2.583,2.042 0.26,0.208 10 false 18 4.677,0.656 4.865,0.865 0.188,0.208 10 false 1 4.677,1.052 4.865,1.26 0.188,0.208 10 false 2 4.677,1.438 4.865,1.646 0.188,0.208 10 false 3 4.969,0.833 5.448,1.042 0.479,0.208 10 false USB- 4.969,1.24 5.448,1.448 0.479,0.208 10 false USB+ 4.969,1.646 5.448,1.854 0.479,0.208 10 false USBS 2.354,1.219 2.729,1.458 0.375,0.24 10 false j16 2.344,1.615 2.719,1.854 0.375,0.24 10 false j16 4.635,1.615 4.938,1.854 0.302,0.24 10 false j15 4.635,1.229 4.917,1.479 0.281,0.25 10 false j15 4.635,0.823 4.917,1.063 0.281,0.24 10 false j15 2.271,2.01 2.646,2.25 0.375,0.24 10 false F174 4.563,2.01 4.938,2.25 0.375,0.24 10 false F175 4.552,2.417 4.927,2.656 0.375,0.24 10 false F175 3.542,1.448 4.208,1.688 0.667,0.24 10 false *1 2.906,3.427 3.75,3.625 0.844,0.198 10 false *1: Shielded 2.271,2.406 2.646,2.646 0.375,0.24 10 false F174 0.719,2.865 3.521,3.083 2.802,0.219 10 false Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall with Single Knob Type Radio and Display)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.

·

Before replacing the telephone transceiver assembly, refer to Service Bulletin.



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

b.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the F174 radio and display receiver assembly connector.


b.

Disconnect the F175 telephone transceiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F174-18 (USBV) - F175-15 (USBV) Always Below 1 Ω
F174-17 (USBG) - F175-31 (USBG) Always Below 1 Ω
F174-18 (USBV) or F175-15 (USBV) - Body ground Always 10 kΩ or higher
F174-17 (USBG) or F175-31 (USBG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.
E434861C07
1.479,0.552 1.854,0.844 0.375,0.292 1.479,2.792 1.854,3.083 0.375,0.292 1.802,1.427 2.219,1.01 true 2.073,2.156 1.74,1.667 true 1.563,1.417 1.26,1.031 true 1.781,3.667 2.188,3.156 true 1.552,3.656 1.25,3.208 true 1.927,4.302 1.698,3.875 true 0.604,0.552 0.917,0.75 0.313,0.198 10 false *a 0.656,2.865 0.969,3.063 0.313,0.198 10 false *b 1.604,0.594 2.104,0.792 0.5,0.198 10 false j16 1.594,2.833 1.938,3.042 0.344,0.208 10 false j15 0.969,0.833 1.573,1.135 0.604,0.302 10 false USB+ 2.104,0.844 2.708,1.146 0.604,0.302 10 false USB- 1.906,2.208 2.51,2.51 0.604,0.302 10 false USBS 1.813,4.365 2.417,4.667 0.604,0.302 10 false USBS 2.135,2.958 2.74,3.26 0.604,0.302 10 false USB+ 1.01,3 1.615,3.302 0.604,0.302 10 false USB-
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to Telephone Transceiver Assembly)


Check the installation condition.

i.

Check the USB communication lines (digital communication line) between the radio and display receiver assembly and the telephone transceiver assembly for any installation or connection problems.



b.

Disconnect the j16 radio and display receiver assembly connector.


c.

Disconnect the j15 telephone transceiver assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j16-1 (USB+) - j15-2 (USB+) Always Below 1 Ω
j16-2 (USB-) - j15-1 (USB-) Always Below 1 Ω
j16-3 (USBS) - j15-3 (USBS) Always Below 1 Ω
j16-1 (USB+) or j15-2 (USB+) - Body ground Always 10 kΩ or higher
j16-2 (USB-) or j15-1 (USB-) - Body ground Always 10 kΩ or higher
j16-3 (USBS) or j15-3 (USBS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE TRANSCEIVER ASSEMBLY IS DEFECTIVE)

NG