Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type with Dual Knob Type) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _061290 NAVIGATION / MULTI INFO DISPLAY _0524476 NAVIGATION SYSTEM(for Radio and Display Type with Dual Knob Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type with Dual Knob Type)  Vehicle Speed Signal Circuit between Navigation ECU and Combination Meter  


DESCRIPTION

The navigation ECU receives a vehicle speed signal from the combination meter assembly.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective systems based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E428293E01
0.146,0.115 2.531,0.354 2.385,0.24 12 false for TMMT made: 2.26,0.281 3.635,0.5 1.375,0.219 10 false to Other Systems 1.25,2.198 3.219,2.479 1.969,0.281 10 false Combination Meter Assembly 1.26,2.042 1.615,2.26 0.354,0.219 10 false F4 2.354,1.417 2.708,1.635 0.354,0.219 10 false +S 2.667,1.292 3.021,1.51 0.354,0.219 10 false 6 5.083,1.302 5.438,1.521 0.354,0.219 10 false 9 5.302,1.417 5.677,1.625 0.375,0.208 10 false SPD 5.313,2.104 5.667,2.323 0.354,0.219 10 false n2 5.313,2.271 6.458,2.583 1.146,0.313 10 false Navigation ECU

E428293E03
0.146,0.115 2.531,0.354 2.385,0.24 12 false for TMC made: 2.26,0.281 3.635,0.5 1.375,0.219 10 false to Other Systems 1.25,2.198 3.219,2.479 1.969,0.281 10 false Combination Meter Assembly 1.26,2.042 1.615,2.26 0.354,0.219 10 false F4 2.354,1.417 2.708,1.635 0.354,0.219 10 false +S 2.667,1.292 3.021,1.51 0.354,0.219 10 false 6 5.083,1.302 5.438,1.521 0.354,0.219 10 false 9 5.302,1.417 5.677,1.625 0.375,0.208 10 false SPD 5.313,2.104 5.667,2.323 0.354,0.219 10 false F168 5.313,2.271 6.458,2.583 1.146,0.313 10 false Navigation ECU

PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E393685C44
1.469,0.333 1.969,0.583 0.5,0.25 2.469,1.969 2.188,1.354 true 0.188,0.188 0.5,0.385 0.313,0.198 10 false *a 1.615,0.365 2.073,0.563 0.458,0.198 10 false F4 2.417,1.979 2.729,2.177 0.313,0.198 10 false +S 2.771,3.594 3.229,3.792 0.458,0.198 10 false GND 1.115,3.844 1.271,4.042 0.156,0.198 10 false A
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal F4-6 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F4-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - COMBINATION METER ASSEMBLY)
a.

Disconnect the n2*1 or F168*2 navigation ECU connector.


b.

Disconnect the F4 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

*1: for TMMT Made

*2: for TMC Made


Standard Resistance:
for TMMT Made
Tester Connection Condition Specified Condition
n2-9 (SPD) - F4-6 (+S) Always Below 1 Ω


for TMC Made
Tester Connection Condition Specified Condition
F168-9 (SPD) - F4-6 (+S) Always Below 1 Ω


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR