Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2019.09
RM32K0E _58 Vehicle Interior _062180 METER / GAUGE / DISPLAY _0304590 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the skid control ECU (brake booster with master cylinder assembly) which uses this information to create the vehicle speed signal*a. The vehicle speed signal consists of pulses sent to the combination meter assembly from the skid control ECU (brake booster with master cylinder assembly). To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly. This voltage is sent to the skid control ECU (brake booster with master cylinder assembly). The pulse signal is created by switching the transistor in the skid control ECU (brake booster with master cylinder assembly) on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the skid control ECU (brake booster with master cylinder assembly). When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on this pulse signal.

*a: This vehicle speed signal is created by the skid control ECU (brake booster with master cylinder assembly). There is no actual component that is referred to as the vehicle speed sensor. In addition, for some systems, vehicle speed information may be received via CAN communication.


HINT:

This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.


WIRING DIAGRAM

E426333E01
0.188,1.052 4.5,1.26 4.313,0.208 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.073,7.313 5.531,7.51 0.458,0.198 10 false F47 0.188,0.896 0.646,1.094 0.458,0.198 10 false A39 0.292,2.177 0.854,2.427 0.563,0.25 10 false F129 2.073,5.625 2.531,5.823 0.458,0.198 10 false F168 4.667,4.75 5.125,4.948 0.458,0.198 10 false F56 0.177,4.75 0.635,4.948 0.458,0.198 10 false F1 5.094,2.167 5.552,2.365 0.458,0.198 10 false F4 0.281,3.625 3.115,3.844 2.833,0.219 10 false Stereo Component Amplifier Assembly*3 5.073,7.49 6.927,7.708 1.854,0.219 10 false Radio Receiver Assembly*1 0.281,2.354 2.917,2.75 2.635,0.396 10 false Radio and Display Receiver Assembly*2 4.667,4.917 7.083,5.25 2.417,0.333 10 false Windshield Wiper Relay Assembly*8 0.167,4.917 3.313,5.25 3.146,0.333 10 false Certification ECU (Smart Key ECU Assembly) 5.073,2.323 6.948,2.583 1.875,0.26 10 false Combination Meter Assembly 0.167,7.427 2.625,7.75 2.458,0.323 10 false *3: w/ Stereo Component Amplifier 0.156,7.083 2.833,7.417 2.677,0.333 10 false *2: for Radio and Display Receiver Type 1.719,0.396 2.177,0.594 0.458,0.198 10 false SP1 1.708,1.688 2.167,1.885 0.458,0.198 10 false SPD 1.698,3 2.156,3.198 0.458,0.198 10 false SPD 1.698,4.26 2.156,4.458 0.458,0.198 10 false SPD 5.198,5.531 5.656,5.729 0.458,0.198 10 false SPD 5.177,2.979 5.635,3.177 0.458,0.198 10 false SPDP 5.167,1.688 5.625,1.885 0.458,0.198 10 false +S 5.188,0.396 5.646,0.594 0.458,0.198 10 false SI 5.854,0.438 6.094,0.635 0.24,0.198 10 false I/F 2.75,2.99 3.208,3.188 0.458,0.198 10 false *3 2.094,0.396 2.396,0.583 0.302,0.188 10 false 11 2.083,3 2.385,3.188 0.302,0.188 10 false 11 4.938,6.813 5.24,7 0.302,0.188 10 false 17 2.083,1.677 2.385,1.865 0.302,0.188 10 false 27 4.938,4.25 5.24,4.438 0.302,0.188 10 false 24 2.094,4.26 2.396,4.448 0.302,0.188 10 false 19 4.969,1.688 5.271,1.875 0.302,0.188 10 false 6 4.979,0.396 5.281,0.583 0.302,0.188 10 false 5 5.844,1.729 6.083,1.927 0.24,0.198 10 false I/F 5.188,4.25 5.646,4.448 0.458,0.198 10 false SPD 5.125,3.635 6.823,4.021 1.698,0.385 10 false Telematics Transceiver*4 5.135,3.479 5.75,3.677 0.615,0.198 10 false F165 4.938,2.979 5.25,3.177 0.313,0.198 10 false 10 4.104,2.979 4.417,3.177 0.313,0.198 10 false *4 0.167,7.75 2.167,8.083 2,0.333 10 false *4: w/ Telematics System 5.177,6.813 5.635,7.01 0.458,0.198 10 false SPD 5.104,6.063 6.802,6.427 1.698,0.365 10 false Brake Actuator Assembly 4.51,5.625 4.969,5.823 0.458,0.198 10 false A85 4.844,5.625 5.302,5.823 0.458,0.198 10 false A84 4.542,5.438 4.844,5.625 0.302,0.188 10 false 27 4.896,5.438 5.198,5.625 0.302,0.188 10 false 27 0.729,6.042 2.25,6.417 1.521,0.375 10 false Navigation ECU*7 0.167,6.75 2,7.083 1.833,0.333 10 false *1: for Radio Receiver Type 0.167,8.083 2.667,8.417 2.5,0.333 10 false *5: for TMC Made 0.167,8.417 2.833,8.75 2.667,0.333 10 false *6: for TMMT Made 2.833,7.75 4.833,8.083 2,0.333 10 false *8: w/ Rain Sensor 2.833,8.083 4.833,8.417 2,0.333 10 false *9: for LHD 2.833,8.417 4.833,8.75 2,0.333 10 false *10: for RHD 4.552,5.823 4.865,6.021 0.313,0.198 10 false *9 4.875,5.823 5.188,6.021 0.313,0.198 10 false *10 0.302,3.469 0.865,3.719 0.563,0.25 10 false F152 2.75,1.677 3.208,1.875 0.458,0.198 10 false *2 4.083,6.792 4.542,6.99 0.458,0.198 10 false *1 2.51,5.625 2.823,5.823 0.313,0.198 10 false n2 2.833,7.417 4.833,7.75 2,0.333 10 false *7: w/ Navigation ECU 2.156,5.823 2.469,6.021 0.313,0.198 10 false *5 2.51,5.823 2.823,6.021 0.313,0.198 10 false *6 3.063,5.531 3.521,5.729 0.458,0.198 10 false *7 4.104,4.25 4.417,4.448 0.313,0.198 10 false *8 2.188,5.448 2.344,5.646 0.156,0.198 10 false 9 2.542,5.438 2.698,5.635 0.156,0.198 10 false 9 1.688,5.542 2.146,5.74 0.458,0.198 10 false SPD

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the ECM or certification ECU (smart key ECU assembly) refer to Service Bulletin.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.INSPECT ECU TERMINAL VOLTAGE (INPUT VOLTAGE)
a.
E188997C47
0.76,0.479 1.177,0.729 0.417,0.25 1.25,1.531 1.448,1.969 true 1.385,1.979 1.688,2.167 0.302,0.188 10 false +S 0.177,0.188 0.427,0.385 0.25,0.198 10 false *a 0.875,0.521 1.333,0.719 0.458,0.198 10 false F4
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-6 (+S) - Body ground Power switch on (IG) 4.5 to 14 V


HINT:

If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.



Result:
Proceed to
OK
NG



OK

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - EACH ECU)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.

Reconnect the F4 combination meter assembly connector.


b.
E341942C04
1.5,0.125 1.906,0.354 0.406,0.229 2.146,1.125 2.833,0.49 true 0.167,0.135 0.479,0.292 0.313,0.156 10 false *a 1.573,0.156 2.094,0.448 0.521,0.292 10 false A39 2.885,0.313 3.406,0.604 0.521,0.292 10 false SP1
*a Front view of wire harness connector
(to skid control ECU (brake booster with master cylinder assembly))


Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A39-11 (SP1) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) (INPUT WAVEFORM)

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU))
3.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) (INPUT WAVEFORM)
a.
B232574C81
1.479,0.469 1.844,0.698 0.365,0.229 2.438,1.948 2.281,1.313 true 0.177,0.156 0.667,0.469 0.49,0.313 10 false *a 2.385,1.99 2.813,2.219 0.427,0.229 10 false SI 2.76,3.646 3.406,3.917 0.646,0.271 10 false GND 1.573,0.49 1.927,0.698 0.354,0.208 10 false F4 0.896,3.76 1.385,4.073 0.49,0.313 10 false A
*a Component with harness connected
(Combination Meter Assembly)


Check the input waveform.

i.

Reconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


ii.

Remove the combination meter assembly with the connector(s) still connected.


iii.

Connect an oscilloscope to terminal F4-5 (SI) and body ground.


iv.

Turn the power switch on (IG).


v.

Turn a wheel slowly.


vi.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Power switch on (IG) wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

REPLACE COMBINATION METER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU))
a.

Disconnect the F4 combination meter assembly connector.


b.

Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-5 (SI) - A39-11 (SP1) Always Below 1 Ω
F4-5 (SI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - EACH ECU)
a.

Disconnect the F47 radio receiver assembly connector.*1


b.

Disconnect the F129 radio and display receiver assembly connector.*2


c.

Disconnect the F152 stereo component amplifier assembly connector.*3


d.

Disconnect the F165 telematics transceiver connector.*4


e.

Disconnect the F168*5 or n2*6 navigation ECU connector.


f.

Disconnect the F56 windshield wiper relay assembly connector.*7


g.

Disconnect the A85*8 or A84*9 brake actuator assembly connector.


h.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


i.

Measure the resistance according to the value(s) in the table below.

*1: for Radio Receiver Type

*2: for Radio and Display Receiver Type

*3: w/ Stereo Component Amplifier

*4: w/ Telematics System

*5: for TMC Made with Navigation ECU

*6: for TMMT Made with Navigation ECU

*7: w/ Rain Sensor

*8: for LHD

*9: for RHD


Standard Resistance:
Tester Connection Condition Specified Condition
F4-6 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CONFIRM MODEL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for Radio Receiver Type A
for Radio and Display Receiver Type B
w/o Radio Receiver C



A

7.INSPECT RADIO RECEIVER ASSEMBLY (SHORT CIRCUIT IN RADIO RECEIVER ASSEMBLY)

B

8.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (SHORT CIRCUIT IN RADIO AND DISPLAY RECEIVER ASSEMBLY)

C

15.CONFIRM MODEL
7.INSPECT RADIO RECEIVER ASSEMBLY (SHORT CIRCUIT IN RADIO RECEIVER ASSEMBLY)
a.

Disconnect the F47 radio receiver assembly connector.


b.

Reconnect the F56 windshield wiper relay assembly connector.*1


c.

Reconnect the F1 certification ECU (smart key ECU assembly) connector.


d.

Reconnect the A85*2 or A84*3 brake actuator assembly connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-6 (+S) - Body ground Power switch on (IG) 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the stereo component amplifier assembly.



*1: w/ Rain Sensor

*2: for LHD

*3: for RHD


Result:
Proceed to
OK
NG



OK

NG

15.CONFIRM MODEL
8.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (SHORT CIRCUIT IN RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the F129 radio and display receiver assembly connector.


b.

Reconnect the F152 stereo component amplifier assembly connector.*1


c.

Reconnect the F165 telematics transceiver connector.*2


d.

Reconnect the F168*3 or n2*4 navigation ECU connector.


e.

Reconnect the F56 windshield wiper relay assembly connector.*5


f.

Reconnect the F1 certification ECU (smart key ECU assembly) connector.


g.

Reconnect the A85*6 or A84*7 brake actuator assembly connector.


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-6 (+S) - Body ground Power switch on (IG) 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the radio receiver assembly.



*1: w/ Stereo Component Amplifier

*2: w/ Telematics System

*3: for TMC Made with Navigation ECU

*4: for TMMT Made with Navigation ECU

*5: w/ Rain Sensor

*6: for LHD

*7: for RHD


Result:
Proceed to
OK
NG



OK

NG

9.CONFIRM MODEL
9.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Stereo Component Amplifier A
w/o Stereo Component Amplifier B



A

10.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (SHORT CIRCUIT IN STEREO COMPONENT AMPLIFIER ASSEMBLY)

B

11.CONFIRM MODEL
10.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (SHORT CIRCUIT IN STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the F152 stereo component amplifier assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-6 (+S) - Body ground Power switch on (IG) 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the radio receiver assembly.



Result:
Proceed to
OK
NG



OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

11.CONFIRM MODEL
11.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Telematics System A
w/o Telematics System B



A

12.INSPECT TELEMATICS TRANSCEIVER (SHORT CIRCUIT IN TELEMATICS TRANSCEIVER)

B

13.CONFIRM MODEL
12.INSPECT TELEMATICS TRANSCEIVER (SHORT CIRCUIT IN TELEMATICS TRANSCEIVER)
a.

Disconnect the F165 telematics transceiver connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-6 (+S) - Body ground Power switch on (IG) 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the stereo component amplifier assembly.



Result:
Proceed to
OK
NG



OK

NG

13.CONFIRM MODEL
13.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Navigation ECU A
w/o Navigation ECU B



A

14.INSPECT NAVIGATION ECU (SHORT CIRCUIT IN NAVIGATION ECU)

B

15.CONFIRM MODEL
14.INSPECT NAVIGATION ECU (SHORT CIRCUIT IN NAVIGATION ECU)
a.

Disconnect the F168*1 or n2*2 navigation ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-6 (+S) - Body ground Power switch on (IG) 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the radio receiver assembly.



*1: for TMC Made

*2: for TMMT Made


Result:
Proceed to
OK
NG



OK

NG

15.CONFIRM MODEL
15.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Rain Sensor A
w/o Rain Sensor B



A

16.INSPECT WINDSHIELD WIPER RELAY ASSEMBLY (SHORT CIRCUIT IN WINDSHIELD WIPER RELAY ASSEMBLY)

B

17.INSPECT BRAKE ACTUATOR ASSEMBLY (SHORT CIRCUIT IN BRAKE ACTUATOR ASSEMBLY)
16.INSPECT WINDSHIELD WIPER RELAY ASSEMBLY (SHORT CIRCUIT IN WINDSHIELD WIPER RELAY ASSEMBLY)
a.

Disconnect the F56 windshield wiper relay assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-6 (+S) - Body ground Power switch on (IG) 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the stereo component amplifier assembly.



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

17.INSPECT BRAKE ACTUATOR ASSEMBLY (SHORT CIRCUIT IN BRAKE ACTUATOR ASSEMBLY)
17.INSPECT BRAKE ACTUATOR ASSEMBLY (SHORT CIRCUIT IN BRAKE ACTUATOR ASSEMBLY)
a.

Disconnect the A85*1 or A84*2 brake actuator assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-6 (+S) - Body ground Power switch on (IG) 4.5 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the stereo component amplifier assembly.



*1: for LHD

*2: for RHD


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)