Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type with Dual Knob Type) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _061817 AUDIO / VIDEO _0524509 AUDIO AND VISUAL SYSTEM(for Radio and Display Type with Dual Knob Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type with Dual Knob Type)  C1622  Back Camera Disconnected  


DESCRIPTION

This DTC is stored if the radio and display receiver assembly judges that the signals or signal lines between the radio and display receiver assembly and the rear television camera assembly are not normal as a result of its self check.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1622 Back Camera Disconnected Open or short in the rear television camera assembly signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Radio and display receiver assembly



WIRING DIAGRAM

E420873E07
0.604,2.792 3.177,3.01 2.573,0.219 10 false Radio and Display Receiver Assembly 1.844,0.521 2.302,0.719 0.458,0.198 10 false CA+ 1.938,0.906 2.25,1.104 0.313,0.198 10 false V+ 1.948,1.302 2.26,1.5 0.313,0.198 10 false V- 1.729,1.719 2.344,1.917 0.615,0.198 10 false CGND 1.75,2.115 2.365,2.313 0.615,0.198 10 false CSLD 0.604,2.594 1.229,2.823 0.625,0.229 10 false F131 2.229,0.427 2.542,0.625 0.313,0.198 10 false 30 2.208,0.802 2.521,1 0.313,0.198 10 false 28 2.219,1.208 2.531,1.406 0.313,0.198 10 false 29 2.24,1.604 2.552,1.802 0.313,0.198 10 false 27 2.229,2.01 2.542,2.208 0.313,0.198 10 false 26 3.604,1.958 3.76,2.156 0.156,0.198 10 false * 5.042,0.521 5.5,0.719 0.458,0.198 10 false CB+ 5.031,0.906 5.49,1.104 0.458,0.198 10 false CV+ 5.042,1.281 5.5,1.479 0.458,0.198 10 false CV- 5.042,1.719 5.656,1.917 0.615,0.198 10 false CGND 4.833,0.406 4.99,0.604 0.156,0.198 10 false 6 4.833,0.813 4.99,1.01 0.156,0.198 10 false 3 4.833,1.208 4.99,1.406 0.156,0.198 10 false 2 4.823,1.604 4.979,1.802 0.156,0.198 10 false 5 4.667,2.354 6.948,2.646 2.281,0.292 10 false Rear Television Camera Assembly 4.771,3.146 6.458,3.344 1.688,0.198 10 false *: Shielded 4.656,2.177 5.292,2.354 0.635,0.177 10 false S11

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type with Dual Knob Type)>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the F131 radio and display receiver assembly connector.


b.

Disconnect the S11 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-30 (CA+) - S11-6 (CB+) Always Below 1 Ω
F131-28 (V+) - S11-3 (CV+) Always Below 1 Ω
F131-29 (V-) - S11-2 (CV-) Always Below 1 Ω
F131-27 (CGND) - S11-5 (CGND) Always Below 1 Ω
F131-26 (CSLD) - Body ground Always Below 1 Ω
F131-30 (CA+) or S11-6 (CB+) - Body ground Always 10 kΩ or higher
F131-28 (V+) or S11-3 (CV+) - Body ground Always 10 kΩ or higher
F131-29 (V-) or S11-2 (CV-) - Body ground Always 10 kΩ or higher
F131-27 (CGND) or S11-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the F131 radio and display receiver assembly connector.


b.
E488381C01
1.427,0.198 1.917,0.479 0.49,0.281 0.542,1.073 1.042,1.344 true 0.75,1.698 1.167,1.385 true 1.271,1.896 1.438,1.375 true 1.521,0.26 1.927,0.531 0.406,0.271 10 false F131 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a 0.219,0.99 0.677,1.188 0.458,0.198 10 false CA+ 0.531,1.594 0.844,1.792 0.313,0.198 10 false V- 0.833,1.813 1.448,2.01 0.615,0.198 10 false CGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-29 (V-) - Body ground Always Below 1 Ω
F131-27 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F131-30 (CA+) - F131-27 (CGND) Power switch on (IG) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

3.INSPECT REAR TELEVISION CAMERA ASSEMBLY

NG

3.INSPECT REAR TELEVISION CAMERA ASSEMBLY
a.

Reconnect the S11 rear television camera assembly connector.


b.
E366062C59
1.5,0.25 1.917,0.5 0.417,0.25 0.833,1.813 1.25,1.396 true 1.167,1.344 0.594,0.948 true 1.552,0.302 2.052,0.542 0.5,0.24 10 false F131 0.125,0.063 0.438,0.26 0.313,0.198 10 false *a 0.385,0.854 0.74,1.073 0.354,0.219 10 false V- 0.615,1.729 0.969,1.948 0.354,0.219 10 false V+
*a Component with harness connected
(Radio and Display Receiver Assembly)


E265840C27
0.813,2.021 1.135,1.583 true 1.469,2 1.229,1.49 true 1.521,4.063 1.281,3.552 true 1,4.156 1.156,3.604 true 0.229,0.229 0.542,0.427 0.313,0.198 10 false *a 0.396,1.052 0.76,1.313 0.365,0.26 10 false GND 0.396,3.208 0.76,3.469 0.365,0.26 10 false GND 0.26,2.271 0.625,2.531 0.365,0.26 10 false *b 0.927,4.177 1.292,4.438 0.365,0.26 10 false *c 0.656,1.979 1.021,2.24 0.365,0.26 10 false *c 1.51,1.969 1.875,2.229 0.365,0.26 10 false *d 1.542,4.052 1.906,4.313 0.365,0.26 10 false *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Using an oscilloscope, check the waveform of the rear television camera assembly.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


OK:

Waveform is similar to that shown in the illustration.


Item Content
Measurement terminal F131-28 (V+) - F131-29 (V-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), shift lever in R

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is on (ACC).




Result:
Proceed to
OK
NG



OK

NG