Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type with Dual Knob Type) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _061817 AUDIO / VIDEO _0524509 AUDIO AND VISUAL SYSTEM(for Radio and Display Type with Dual Knob Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type with Dual Knob Type)  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio and display receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs. Therefore, the radio and display receiver assembly cannot be operated using the steering pad switch assembly, also the radio and display receiver assembly itself will not function.

WIRING DIAGRAM

E360347E06
6.271,4.448 7.156,5.188 0.885,0.74 10 false Radio and Display Receiver Assembly 4.698,4.271 5.583,5.01 0.885,0.74 10 false Spiral Cable with Sensor Sub-assembly 6.271,4.271 6.885,4.469 0.615,0.198 10 false F129 6.438,3.583 7.052,3.781 0.615,0.198 10 false SW2 6.438,1.99 7.052,2.188 0.615,0.198 10 false SWG 6.427,0.802 7.042,1 0.615,0.198 10 false SW1 5.5,3.563 6.115,3.76 0.615,0.198 10 false F29 5.521,2 6.135,2.198 0.615,0.198 10 false F29 5.521,0.792 6.135,0.99 0.615,0.198 10 false F29 4.979,0.688 5.594,0.885 0.615,0.198 10 false AU1 4.99,1.854 5.604,2.052 0.615,0.198 10 false EAU 4.969,3.469 5.583,3.667 0.615,0.198 10 false AU2 4.51,3.563 5.125,3.76 0.615,0.198 10 false z1 4.542,1.99 5.156,2.188 0.615,0.198 10 false z1 4.531,0.792 5.146,0.99 0.615,0.198 10 false z1 6.135,3.448 6.75,3.646 0.615,0.198 10 false 22 6.167,1.875 6.781,2.073 0.615,0.198 10 false 24 6.177,0.688 6.792,0.885 0.615,0.198 10 false 21 5.583,0.573 6.198,0.771 0.615,0.198 10 false 6 5.583,1.75 6.198,1.948 0.615,0.198 10 false 3 5.583,3.333 6.198,3.531 0.615,0.198 10 false 5 4.531,3.333 5.146,3.531 0.615,0.198 10 false 10 4.573,1.76 5.188,1.958 0.615,0.198 10 false 8 4.542,0.563 5.156,0.76 0.615,0.198 10 false 11 2.594,4.531 3.354,4.75 0.76,0.219 10 false On hook 1.76,4.531 2.521,4.75 0.76,0.219 10 false Off hook 1.125,4.521 1.885,4.74 0.76,0.219 10 false Voice 1.875,2.958 2.635,3.177 0.76,0.219 10 false MODE 0.229,1.375 0.99,1.594 0.76,0.219 10 false Volume- 1,1.375 1.76,1.594 0.76,0.219 10 false Volume+ 1.906,1.375 2.667,1.594 0.76,0.219 10 false Seek- 2.719,1.385 3.479,1.604 0.76,0.219 10 false Seek+ 1.26,5.729 4.406,5.979 3.146,0.25 10 false Steering Pad Switch Assembly 6.177,2.094 6.792,2.292 0.615,0.198 10 false *1 0.198,6.427 3.344,6.677 3.146,0.25 10 false *1: for Built-in Type

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)
a.

Disconnect the F129 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F129-21 (SW1) - F129-24 (SWG) No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Seek- switch pushed 313 to 345 Ω
Volume+ switch pushed 950 to 1050 Ω
Volume- switch pushed 2955 to 3265 Ω
F129-22 (SW2) - F129-24 (SWG) No switch pushed 95 to 105 kΩ
MODE switch pushed Below 2.5 Ω
On hook switch pushed 313 to 345 Ω
Off hook switch pushed 950 to 1050 Ω
Voice switch pushed 2955 to 3265 Ω



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL W/SENSOR CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL W/SENSOR CABLE SUB-ASSEMBLY
a.

Remove the spiral cable with sensor sub-assembly.


b.

Inspect the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION

NOTICE:
·

Press and hold the lock located in the center of the spiral cable with sensor sub-assembly to rotate the spiral cable with sensor sub-assembly.

·

The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying.

·

As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.




Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - BODY GROUND)

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY