Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type with Single Knob Type) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _061817 AUDIO / VIDEO _0525784 AUDIO AND VISUAL SYSTEM(for Radio and Display Type with Single Knob Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type with Single Knob Type)  B15DB87  Telematics Transceiver Missing Message  


DESCRIPTION

When the radio and display receiver assembly cannot detect the telematics transceiver, this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15DB87 Telematics Transceiver Missing Message When 90 seconds has elapsed after turning the ignition switch to ON and the telematics transceiver cannot be detected, the telematics transceiver is judged to be disconnected after comparison with the past USB connected devices information.
(2 trip detection logic)
·

Telematics transceiver

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

E427424E68
5.854,3.156 7.052,3.688 1.198,0.531 10 false Radio and Display Receiver Assembly 2.563,3.156 4.208,3.531 1.646,0.375 10 false Telematics Transceiver 0.75,3.208 2.635,3.51 1.885,0.302 10 false : USB Communication Line 0.135,0.333 1.021,0.854 0.885,0.521 10 false from Auxiliary Battery 0.052,1.292 1.031,1.896 0.979,0.604 10 false from IG2-NO. 2 Relay 1.281,1.458 2.365,1.75 1.083,0.292 10 false ECU-IG2 NO. 3 1.219,0.5 2.25,0.698 1.031,0.198 10 false DCM/MAYDAY 3.823,0.333 4.177,0.594 0.354,0.26 10 false j15 3.76,2.375 4.135,2.573 0.375,0.198 10 false F175 2.771,0.344 3.313,0.667 0.542,0.323 10 false +B 2.781,1.302 3.323,1.625 0.542,0.323 10 false IG2 2.792,2.25 3.125,2.573 0.333,0.323 10 false E 3.26,0.333 3.813,0.625 0.552,0.292 10 false USB+ 3.281,0.823 3.833,1.115 0.552,0.292 10 false USB- 3.25,1.292 3.802,1.583 0.552,0.292 10 false USBS 6.052,2.375 6.604,2.667 0.552,0.292 10 false USBV 3.26,2.844 3.813,3.135 0.552,0.292 10 false USBG 6.063,2.854 6.615,3.146 0.552,0.292 10 false USBG 6.073,0.354 6.625,0.646 0.552,0.292 10 false USB+ 6.063,0.833 6.615,1.125 0.552,0.292 10 false USB- 6.063,1.302 6.615,1.594 0.552,0.292 10 false USBS 4.844,1.031 5.198,1.271 0.354,0.24 10 false * 3.26,2.385 3.813,2.677 0.552,0.292 10 false USBV 2.438,0.146 2.854,0.479 0.417,0.333 10 false 1 2.406,1.094 2.823,1.427 0.417,0.333 10 false 19 2.417,2.052 2.833,2.385 0.417,0.333 10 false 20 3.875,0.625 4.292,0.958 0.417,0.333 10 false 1 3.875,0.146 4.292,0.479 0.417,0.333 10 false 2 3.885,1.094 4.302,1.427 0.417,0.333 10 false 3 3.854,2.188 4.167,2.417 0.313,0.229 10 false 15 3.854,2.667 4.271,3 0.417,0.333 10 false 31 5.677,2.188 6.031,2.375 0.354,0.188 10 false 18 5.677,2.656 5.958,2.833 0.281,0.177 10 false 17 5.719,0.156 6.135,0.49 0.417,0.333 10 false 1 5.729,0.635 6.146,0.969 0.417,0.333 10 false 2 5.729,1.094 6.146,1.427 0.417,0.333 10 false 3 3.771,2.854 4.125,3.052 0.354,0.198 10 false F175 2.333,2.24 2.688,2.438 0.354,0.198 10 false F175 2.333,1.292 2.688,1.49 0.354,0.198 10 false F175 2.344,0.344 2.698,0.542 0.354,0.198 10 false F175 3.833,0.802 4.188,1.063 0.354,0.26 10 false j15 3.833,1.281 4.188,1.542 0.354,0.26 10 false j15 5.688,0.823 6.042,1.083 0.354,0.26 10 false j16 5.604,2.844 6.063,3.042 0.458,0.198 10 false F174 5.604,2.375 6.063,2.573 0.458,0.198 10 false F174 0.177,2.885 1.208,3.125 1.031,0.24 10 false *: Shielded 5.688,0.333 6.042,0.594 0.354,0.26 10 false j16 5.677,1.281 6.031,1.542 0.354,0.26 10 false j16

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the telematics transceiver, make sure to replace it with a new one.

·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type with Single Knob Type)>PRECAUTION



HINT:

This DTC may be stored due to environmental reasons such as electrical noise or interference.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - POWER SOURCE AND BODY GROUND)
a.

Disconnect the F175 telematics transceiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F175-20 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F175-1 (+B) - F175-20 (E) IG OFF 11 to 14 V
F175-19 (IG2) - F175-20 (E) IG ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the F174 radio and display receiver assembly connector.


b.

Disconnect the F175 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F174-18 (USBV) - F175-15 (USBV) Always Below 1 Ω
F174-17 (USBG) - F175-31 (USBG) Always Below 1 Ω
F174-18 (USBV) or F175-15 (USBV) - Body ground Always 10 kΩ or higher
F174-17 (USBG) or F175-31 (USBG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (USBV, USBG)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (USBV, USBG)
a.

With the radio and display receiver assembly connectors connected, disconnect the F175 telematics transceiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F175-31 (USBG) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F175-15 (USBV) - F175-31 (USBG) IG ON 3 V or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

NG

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.
E477878C04
1.479,0.302 1.927,0.583 0.448,0.281 1.458,2.563 1.906,2.844 0.448,0.281 1.823,1.292 2.292,0.875 true 1.552,1.302 1.073,0.865 true 1.625,1.521 1.167,1.802 true 1.594,3.594 1.135,3.875 true 1.552,3.396 1.083,3.125 true 2.271,3.104 1.813,3.385 true 1.115,0.156 1.427,0.354 0.313,0.198 10 false *a 1.094,2.448 1.406,2.646 0.313,0.198 10 false *b 1.604,0.354 2.063,0.552 0.458,0.198 10 false j15 1.594,2.615 2.052,2.813 0.458,0.198 10 false j16 2.333,3.01 2.948,3.208 0.615,0.198 10 false USB- 2.354,0.771 2.969,0.969 0.615,0.198 10 false USB+ 0.771,1.823 1.385,2.021 0.615,0.198 10 false USBS 0.656,3 1.271,3.198 0.615,0.198 10 false USB+ 0.656,0.74 1.271,0.938 0.615,0.198 10 false USB- 0.719,3.875 1.333,4.073 0.615,0.198 10 false USBS
*a Front view of wire harness connector
(to Telematics Transceiver)
*b Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the j16 radio and display receiver assembly connector.


b.

Disconnect the j15 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j15-2 (USB+) - j16-1 (USB+) Always Below 1 Ω
j15-1 (USB-) - j16-2 (USB-) Always Below 1 Ω
j15-3 (USBS) - j16-3 (USBS) Always Below 1 Ω
j15-2 (USB+) or j16-1 (USB+) - Body ground Always 10 kΩ or higher
j15-1 (USB-) or j16-2 (USB-) - Body ground Always 10 kΩ or higher
j15-3 (USBS) or j16-3 (USBS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 496

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON and wait for 90 seconds.


d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON and wait for 90 seconds.


f.

Using the GTS, recheck for DTCs and proceed to the following step.

Body Electrical > Navigation System > Trouble Codes
50001 496
Result:
Result Proceed to
DTCs are not output A
DTC B15DB87 is output B




A

END (TELEMATICS TRANSCEIVER IS DEFECTIVE)

B