Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P261029  ECM/PCM Engine Off Timer Performance Signal Invalid  


DESCRIPTION

The soak timer operates after the ignition switch is turned off. When a certain amount of time has elapsed after turning the ignition switch off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the engine is stopped. The soak timer is built into the ECM.

A384865E01
5.115,4.042 5.573,4.24 0.458,0.198 10 false ECM 3.875,0.635 4.49,0.833 0.615,0.198 10 false IGSW 4.563,1.031 5.281,1.406 0.719,0.375 10 false Soak Timer IC 4.552,2.354 5.167,2.958 0.615,0.604 10 false Power Source IC 4.542,3.167 5.281,3.719 0.74,0.552 10 false MAIN Relay Control IC 4.073,2.333 4.385,2.531 0.313,0.198 10 false +B 3.99,2.656 4.448,2.854 0.458,0.198 10 false +B2 3.885,3.25 4.5,3.448 0.615,0.198 10 false MREL 2.302,1.49 3.031,1.688 0.729,0.198 10 false IG2 NO. 1 0.115,0.74 1.125,0.958 1.01,0.219 10 false from IG2 Fuse 0.417,1.875 3.646,2.333 3.229,0.458 10 false from Certification ECU (Smart Key ECU Assembly)*1 or Ignition or Starter Switch Assembly*2 2.344,3.698 3.135,3.896 0.792,0.198 10 false EFI-MAIN 1.26,3.115 2.302,3.313 1.042,0.198 10 false EFI-MAIN NO. 1 0.25,2.948 1.135,3.188 0.885,0.24 10 false from Battery 0.146,3.875 2.104,4.073 1.958,0.198 10 false *1: w/ Entry and Start System 0.156,4.333 2.167,4.542 2.01,0.208 10 false *2: w/o Entry and Start System

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P261029 ECM/PCM Engine Off Timer Performance Signal Invalid ECM internal malfunction (2 trip detection logic). ECM Comes on (Euro-OBD)/- (Except Euro-OBD) DTC stored (Euro-OBD)/- (Except Euro-OBD) SAE Code:
P2610

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine.

9.

Idle the engine for 10 minutes or more.

10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P261029.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

HINT:
·

DTC P261029 is set if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is required.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

2.CHECK WHETHER DTC OUTPUT RECURS (DTC P261029)
2.CHECK WHETHER DTC OUTPUT RECURS (DTC P261029)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

j.

If no pending DTC is output, the repair has been successfully completed.


Result:
Proceed to
NEXT



NEXT

END