Home › Suspension › FRONT SUSPENSION › FRONT STABILIZER BAR
RM32H0E _53 Suspension _059519 FRONT SUSPENSION _0291586 FRONT STABILIZER BAR A

FRONT SUSPENSION  FRONT STABILIZER BAR  INSTALLATION  


PROCEDURE

Hide 48815E 1.INSTALL FRONT STABILIZER BAR BUSHING LH

a.
C345321C02
2.365,1.323 2.906,1.938 2.906,1.938 3.01,1.938 true 0.646,0.615 0.76,0.615 0.76,0.615 1.26,1.031 false 3.052,1.854 3.365,2.01 0.313,0.156 10 false *a 0.469,0.531 0.781,0.688 0.313,0.156 10 false *b
*a Cutout
*b Stopper
V100135

Front of the Vehicle
V100136

Outside of the Vehicle


Install the front stabilizer bar bushing LH to the front stabilizer bar as shown in the illustration.

NOTICE:
·

Install the front stabilizer bar bushing LH so that the cutout is facing the rear of the vehicle.

·

Install the front stabilizer bar bushing LH onto the front stabilizer bar so that the stopper ring of the front stabilizer bar faces the outside of the vehicle.




Hide 48815E 2.INSTALL FRONT STABILIZER BAR BUSHING RH

HINT:

Perform the same procedure as for the LH side.


Hide 48811 3.INSTALL FRONT STABILIZER BAR

a.

Install the front stabilizer bar with the 2 front stabilizer bar bushings to the front suspension crossmember sub-assembly.

NOTICE:

Make sure that the identification mark is positioned on the right side of the vehicle.


C345322C02
6.885,0.99 6.99,0.99 6.99,0.99 6.99,2.031 false 6.938,2.052 7.115,2.313 0.177,0.26 10 false *a
*a Identification Mark - -
V100135

Front of the Vehicle - -



Hide 48829A 4.INSTALL FRONT NO. 1 STABILIZER BRACKET LH

a.
C365739C01
2.833,1.083 2.667,1.083 2.667,1.083 2.531,0.667 false 2.938,0.969 3.25,1.167 0.313,0.198 10 false *a 2.313,1.948 2.458,2.146 0.146,0.198 10 true B 1.99,2.813 2.219,3.01 0.229,0.198 10 false A
*a Arrow
V100136

Front of the Vehicle


Install the front No. 1 stabilizer bracket LH to the front suspension crossmember sub-assembly with the 2 bolts.

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

NOTICE:
·

Make sure to install the front No. 1 stabilizer bracket LH with its arrow facing the front of the vehicle.

·

Temporarily tighten the bolt (B) and then fully tighten the 2 bolts in the order of (A) and (B).




Hide 48824A 5.INSTALL FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.


Hide 48810 6.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

a.

Install the front stabilizer link assembly LH to the front stabilizer bar LH with the nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 48820B 7.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 8.INSTALL STEERING LINK ASSEMBLY

a.

Install the steering link assembly to the front suspension crossmember sub-assembly with the 2 bolts and 2 new nuts.

Torque:
133 N*m (1356 kgf*cm, 98 ft.*lbf)

NOTICE:
·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

·

Make sure to tighten the bolts starting from the left side of the vehicle.




Hide 51201 9.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY