Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER › 2016.10–2019.09
RM32H0E _53 Suspension _059519 FRONT SUSPENSION _0291587 FRONT SUSPENSION MEMBER A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL HOLE PLUG

a.

Install the 4 hole plugs to the front suspension crossmember sub-assembly.

HINT:

There are 2 different shapes of hole plug.



Hide 51228G 2.INSTALL FRONT SUSPENSION MEMBER PLATE

a.

Install the 2 front suspension member plates to the front suspension crossmember sub-assembly.


Hide 12363A 3.INSTALL ENGINE MOVING CONTROL ROD

a.

Install the engine moving control rod to the front suspension crossmember sub-assembly with the bolt.

Torque:
200 N*m (2039 kgf*cm, 148 ft.*lbf)


Hide 48069 4.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Temporarily install the front lower No. 1 suspension arm sub-assembly LH to the front suspension crossmember sub-assembly with the 2 bolts and nut.


Hide 48068 5.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48811 6.INSTALL FRONT STABILIZER BAR

Hide 48829A 7.INSTALL FRONT NO. 1 STABILIZER BRACKET LH

Hide 48824A 8.INSTALL FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.


Hide 9.INSTALL STEERING LINK ASSEMBLY

a.

Install the steering link assembly to the front suspension crossmember sub-assembly with the 2 bolts and 2 new nuts.

Torque:
133 N*m (1356 kgf*cm, 98 ft.*lbf)

NOTICE:
·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

·

Make sure to tighten the bolts starting from the left side of the vehicle.




Hide 51201 10.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Slowly jack up the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools.

CAUTION:
C345334

·

The front suspension crossmember sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the front suspension crossmember sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:

Use attachments to keep the front suspension crossmember sub-assembly level.



b.

Install the front suspension crossmember sub-assembly to the vehicle body with the 6 bolts.

Torque:
141 N*m (1438 kgf*cm, 104 ft.*lbf)


c.

Lower the engine lifter.


d.

Install the engine moving control rod with the bolt.

Torque:
170 N*m (1734 kgf*cm, 125 ft.*lbf)


e.

for AWD:

i.

Install the wire harness clamp bracket to the front suspension crossmember sub-assembly with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)



f.

for 2WD:

i.

Install the 2 wire harness clamp brackets to the front suspension crossmember sub-assembly with the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)



Hide 48069 11.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Install the front lower No. 1 suspension arm sub-assembly LH to the front lower ball joint assembly LH with the bolt and 2 nuts.

Torque:
89 N*m (908 kgf*cm, 66 ft.*lbf)


Hide 48068 12.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45047 13.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 45046 14.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48810 15.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

a.

Connect the front stabilizer link assembly LH to the front shock absorber assembly with the nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

NOTICE:

Do not damage the boot of the ball joint.


HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 48820B 16.CONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51108A 17.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

a.

Install the rear side rail reinforcement sub-assembly LH to the front suspension crossmember sub-assembly and vehicle body with the 4 bolts.

Torque:
70 N*m (714 kgf*cm, 52 ft.*lbf)


Hide 51107A 18.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45025D 19.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45260 20.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 21.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 22.INSTALL FRONT WHEELS

Hide 48069 24.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 25.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 58166 26.INSTALL FRONT FLOOR COVER LH (w/ Cover)

Hide 58165B 27.INSTALL FRONT FLOOR COVER RH (w/ Cover)

HINT:

Use the same procedure as for the LH side.


Hide 51444A 28.INSTALL REAR ENGINE UNDER COVER LH

Hide 51443C 29.INSTALL REAR ENGINE UNDER COVER RH

Hide 51441 30.INSTALL NO. 1 ENGINE UNDER COVER

Hide 31.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT