Home › Suspension › REAR SUSPENSION › REAR TRAILING ARM › 2016.10–2019.09
RM32H0E _53 Suspension _059601 REAR SUSPENSION _0292269 REAR TRAILING ARM A

REAR SUSPENSION  REAR TRAILING ARM  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear trailing arm assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 57628C 2.REMOVE REAR FLOOR SIDE MEMBER COVER LH (for 2WD)

Hide 57627A 3.REMOVE REAR FLOOR SIDE MEMBER COVER RH (for 2WD)

Hide 57628C 4.REMOVE REAR FLOOR SIDE MEMBER COVER LH (for AWD)

Hide 57627A 5.REMOVE REAR FLOOR SIDE MEMBER COVER RH (for AWD)

Hide 890C0A 6.SEPARATE NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.

for 2WD:

i.
C365332

Using a screwdriver with its tip wrapped in protective tape, disconnect the No. 2 parking brake wire connector from the rear axle hub and bearing assembly.

NOTICE:

Be careful not to damage the rear axle hub and bearing assembly and connector cover.




b.

for AWD:

i.
C365333

Using a screwdriver with its tip wrapped in protective tape, disconnect the No. 2 parking brake wire connector from the rear axle hub and bearing assembly.

NOTICE:

Be careful not to damage the rear axle hub and bearing assembly and connector cover.




c.
C365334

Disengage the clamp.


d.

Remove the nut to separate the No. 2 parking brake wire assembly from the rear trailing arm assembly.


Hide 48840A 7.REMOVE REAR STABILIZER LINK ASSEMBLY

Hide 48780E 8.REMOVE REAR TRAILING ARM ASSEMBLY

a.
C365335C01
0.427,1.458 1.375,1.458 true 2.281,1.74 2.552,1.74 true 0.229,1.323 0.542,1.521 0.313,0.198 10 false *a 2.615,1.604 2.927,1.802 0.313,0.198 10 false *b
*a Wooden Block
*b Transmission Jack


Using a transmission jack and a wooden block, support the rear No. 2 suspension arm assembly.

NOTICE:
·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.




b.
C345069

Remove the 2 bolts to separate the rear trailing arm assembly from the rear axle carrier sub-assembly.


c.
C365336

Remove the 4 bolts and rear trailing arm assembly.


Hide 48753C 9.REMOVE NO. 1 REAR SUSPENSION SUPPORT COVER

a.
C365337

Secure the rear trailing arm assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C365338

Disengage the 3 claws to remove the NO. 1 rear suspension support cover.


Hide 48727 10.REMOVE REAR SUSPENSION ARM BRACKET

a.
C365339

Remove the bolt, nut and rear suspension arm bracket from the rear trailing arm assembly.

NOTICE:

Because the bolt has its own stopper, do not turn the bolt. Loosen the nut with the bolt secured.