The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel tank assembly removal/installation are shown below.
*1: When performing learning using the GTS.
*2: w/ Stop and start system
Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
Because the weight of the fuel tank sub-assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.
If work is not performed according to the procedures described in the repair manual, there is a danger that the components could fall down.
When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.
Touching high-temperature areas such as the engine and exhaust pipe could result in burns.
77020A
1.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
77010
2.REMOVE FUEL TANK VENT TUBE ASSEMBLY
3.DRAIN FUEL
4.REMOVE EXHAUST PIPE ASSEMBLY
37100
5.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
57628C
6.REMOVE REAR FLOOR SIDE MEMBER COVER LH
Remove the 2 bolts and 2 clips (A).
Disengage the clip (B) to remove the floor side member cover LH.
57627A
7.REMOVE REAR FLOOR SIDE MEMBER COVER RH
Remove the 2 bolts and 2 clips (A).
Disengage the clip (B) to remove the rear side member cover RH.
77642A
8.REMOVE NO. 2 FUEL TANK PROTECTOR
Remove the nut, 4 clips and No. 2 fuel tank protector from the fuel tank assembly.
77641A
9.REMOVE NO. 1 FUEL TANK PROTECTOR
Remove the 4 clips and No. 1 fuel tank protector from the fuel tank assembly.
77754B
10.DISCONNECT CHARCOAL CANISTER OUTLET HOSE
Slide the hose clip and disconnect the charcoal canister outlet hose from the fuel tank filler pipe sub-assembly.
11.DISCONNECT FUEL TANK BREATHER TUBE
Disconnect the fuel tank breather tube from the fuel tank filler pipe sub-assembly.
Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>PRECAUTION
77213E
12.DISCONNECT FUEL TANK TO FILLER PIPE HOSE
Loosen the clamp, then disconnect the fuel tank to filler pipe hose from the fuel tank assembly.
77026A
13.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
Disconnect the fuel tube connector to remove the No. 1 fuel evaporation tube sub-assembly from the fuel pipe.
Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>PRECAUTION
77209F
14.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Disconnect the fuel tube connector to remove the fuel tank main tube sub-assembly from the fuel pipe.
Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>PRECAUTION
77100
15.REMOVE FUEL TANK ASSEMBLY
The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.
Support the fuel tank assembly using an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.
Remove the 4 bolts and No. 1 fuel tank band sub-assemblies.
Lower the engine lifter to remove the fuel tank assembly.
Be careful not to drop the fuel tank assembly.
When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.
77656B
16.REMOVE NO. 6 FUEL TANK CUSHION
Remove the 3 No. 6 fuel tank cushions from the fuel tank assembly.
77754B
17.REMOVE CHARCOAL CANISTER OUTLET HOSE
Disengage the clamp to remove the charcoal canister outlet hose from the fuel tank assembly.