Home › Engine / Hybrid System › CRUISE CONTROL › SPEED LIMITER SYSTEM
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0292290 SPEED LIMITER SYSTEM J

CRUISE CONTROL  SPEED LIMITER SYSTEM  Speed Limiter System does not Operate  


DESCRIPTION

When the speed limiter is turned on using the speed limiter switch, the ECM illuminates the speed limiter indicator and activates the speed limiter system. Each function of the speed limiter system can be activated by operating the cruise control main switch. When the cruise control system is operating, the speed limiter system will not operate.

WIRING DIAGRAM

C367112E02
1.563,0.771 2.458,1.198 0.896,0.427 10 false Speed Limiter Switch 2.792,0.615 3.104,0.813 0.313,0.198 10 false z1 2.823,0.417 3.135,0.615 0.313,0.198 10 false 9 2.792,1.573 3.104,1.771 0.313,0.198 10 false z1 2.823,1.385 3.135,1.583 0.313,0.198 10 false 7 1.323,2.125 2.615,2.542 1.292,0.417 10 false Steering Pad Switch Assembly 3.573,0.531 3.948,0.729 0.375,0.198 10 false ASL 3.563,1.49 3.938,1.688 0.375,0.198 10 false ECC 4.01,0.604 4.385,0.802 0.375,0.198 10 false F29 4.01,1.573 4.385,1.771 0.375,0.198 10 false F29 4.094,0.417 4.406,0.615 0.313,0.198 10 false 4 4.094,1.375 4.406,1.573 0.313,0.198 10 false 2 5.146,1.49 5.521,1.688 0.375,0.198 10 false 41 5.146,0.531 5.521,0.729 0.375,0.198 10 false 22 5.438,0.625 5.917,0.813 0.479,0.188 10 false ASLM 5.438,1.594 5.917,1.792 0.479,0.198 10 false ECCS 5.594,2.292 6.073,2.49 0.479,0.198 10 false ECM 5.604,2.125 6.083,2.323 0.479,0.198 10 false A38 2.969,2.125 4.063,2.5 1.094,0.375 10 false Spiral Cable Sub-assembly

PROCEDURE

1.CHECK CRUISE CONTROL SYSTEM
a.

Turn the ignition switch to ON.


b.

Turn the cruise control on using the cruise control main switch.


c.

Check the operation of each function by operating the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM (for 8NR-FTS)>ROAD TEST


OK:

Each function of the cruise control system operates normally.


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (ASL SW)

NG

2.READ VALUE USING GTS (ASL SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus : Powertrain / Engine / Data List / ASL SW.


e.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ASL SW Speed limiter switch signal ON or OFF OFF: Speed limiter switch off
ON: Speed limiter switch on
-
Powertrain > Engine > Data List
Tester Display
ASL SW
50003 372 380
OK:

The Data List item ASL SW changes according to the operation of the switch.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)
a.

Disconnect the A38 ECM connector.


b.

Disconnect the F29 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-22 (ASLM) - F29-4 (ASL) Always Below 1 Ω
A38-22 (ASLM) or F29-4 (ASL) - Body ground Always 10 kΩ or higher
F29-2 (ECC) - A38-41 (ECCS) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

5.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE STEERING PAD SWITCH