Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM (for 8NR-FTS)
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0297888 CRUISE CONTROL SYSTEM(for 8NR-FTS) Y

CRUISE CONTROL  CRUISE CONTROL SYSTEM(for 8NR-FTS)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Perform the following procedure to troubleshoot the cruise control system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.INSPECT BATTERY VOLTAGE
2.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

3.CHECK CAN COMMUNICATION SYSTEM*
3.CHECK CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check that the CAN communication system is functioning normally.

OK:

CAN communication system is functioning normally.


HINT:

Refer to CAN Bus Check in CAN Communication System.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



Result:
Proceed to
OK
NG



OK

4.CHECK METER / GAUGE SYSTEM*

NG

4.CHECK METER / GAUGE SYSTEM*
a.

Use the GTS to check if the meter / gauge system is functioning normally.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122

Result:
Result Proceed to
Meter / gauge system DTCs are not output A
Meter / gauge system DTCs are output B



A

5.CHECK VEHICLE STABILITY CONTROL SYSTEM

B

5.CHECK VEHICLE STABILITY CONTROL SYSTEM
a.

Use the GTS to check if the vehicle stability control system is functioning normally.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105

Result:
Result Proceed to
Vehicle stability control system DTCs are not output A
Vehicle stability control system DTCs are output B



A

6.CHECK FOR DTCs (CRUISE CONTROL SYSTEM)*

B

6.CHECK FOR DTCs (CRUISE CONTROL SYSTEM)*
a.

Check for DTCs, and note down any DTCs that are output.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM (for 8NR-FTS)>DTC CHECK / CLEAR

Powertrain > Cruise Control > Trouble Codes
50001 374

b.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM (for 8NR-FTS)>DTC CHECK / CLEAR

Powertrain > Cruise Control > Clear DTCs
50002 374

c.

Recheck for DTCs. Try to reproduce the DTCs by duplicating the conditions indicated by the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM (for 8NR-FTS)>DTC CHECK / CLEAR

Powertrain > Cruise Control > Trouble Codes
50001 374

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

7.PROBLEM SYMPTOMS TABLE

B

7.PROBLEM SYMPTOMS TABLE
HINT:

Refer to Problem Symptoms Table.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM (for 8NR-FTS)>PROBLEM SYMPTOMS TABLE


Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

9.REPAIR OR REPLACE
8.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

9.REPAIR OR REPLACE
9.REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

10.CONFIRMATION TEST
10.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END