Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY
RM32H0E _55 Steering _059604 STEERING COLUMN _0292296 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

Do not drop the power steering ECU assembly, strike it with tools or subject it to impacts.

·

If the power steering ECU assembly is subjected to an impact, replace it with a new one.

·

Do not pull the wire harness.

·

Do not allow any moisture to come into contact with the power steering ECU assembly.

·

Do not loosen any bolts not mentioned in the procedure.

·

Do not allow any foreign matter to contaminate the power steering ECU assembly.



PROCEDURE

Hide 89782 1.REMOVE TRANSPONDER KEY COIL (w/o Entry and Start System)

Hide 45020B 2.REMOVE UPPER STEERING COLUMN BRACKET WITH SWITCH ASSEMBLY (w/o Entry and Start System)

a.

Secure the steering column assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Using a center punch, mark the center of the tapered-head bolt.


c.

Using a 3 to 4 mm (0.119 to 0.157 in.) drill, drill a hole in the bolt.


d.
C322177C01
2.135,1.073 2.531,1.365 false 2.625,1.323 2.938,1.479 0.313,0.156 10 false *a
*a Screw Extractor


Using a screw extractor, remove the bolt and upper steering column bracket with switch assembly from the steering column assembly.


Hide 69057A 3.REMOVE IGNITION SWITCH LOCK CYLINDER ASSEMBLY (w/o Entry and Start System)

a.
C324269C02
2.104,0.396 2.292,0.635 true 1.969,0.302 2.125,0.458 0.156,0.156 10 false *c 0.646,0.208 0.958,0.365 0.313,0.156 10 false *a 1.646,2.76 1.958,2.917 0.313,0.156 10 false *b 2.948,1.896 3.26,2.052 0.313,0.156 10 false *b
*a Push
*b Pull
*c ACC


Turn the ignition switch to ACC.


b.

Insert the tip of a screwdriver into the hole in the upper steering column bracket assembly as shown in the illustration, and pull the ignition switch lock cylinder out until its claw comes into contact with the stopper of the upper steering column bracket assembly.

NOTICE:

Pull the ignition switch lock cylinder assembly out until its claw comes into contact with the stopper of the upper steering column bracket assembly. Otherwise, the following procedure cannot be conducted properly.



c.
C324270C01
0.469,0.667 0.667,1.302 0.667,1.302 0.833,1.302 true 0.25,0.333 0.333,0.333 0.333,0.333 0.396,0.583 true 0.865,1.219 1.177,1.375 0.313,0.156 10 false *1 0.104,0.26 0.417,0.417 0.313,0.156 10 false *2 1.719,3.125 2.031,3.281 0.313,0.156 10 false *a 2.146,0.271 2.458,0.427 0.313,0.156 10 false *b 2.583,3.115 2.896,3.271 0.313,0.156 10 false *c
*1 Stopper
*2 Claw
*a Tilt
*b Claw is detached
*c Pull out


Insert the tip of a screwdriver into the hole in the upper steering column bracket assembly and tilt it downward as shown in the illustration to detach the claw of the ignition switch lock cylinder. Then pull out the ignition switch lock cylinder.


Hide 84052 4.REMOVE UN-LOCK WARNING SWITCH ASSEMBLY (w/o Entry and Start System)

a.
C328391

Insert the key.


b.

Disengage the 2 claws to remove the un-lock warning switch assembly.


Hide 84450 5.REMOVE IGNITION OR STARTER SWITCH ASSEMBLY (w/o Entry and Start System)

a.
C321964

Remove the 2 screws and ignition or starter switch assembly.


Hide 85432 6.REMOVE KEY INTERLOCK SOLENOID (w/o Entry and Start System)

a.

for CVT:

i.
C324271

Remove the screw and key interlock solenoid from the upper steering column bracket assembly.



Hide 45020B 7.REMOVE STEERING LOCK ACTUATOR ASSEMBLY (w/ Entry and Start System)

a.

Secure the steering column assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Using a center punch, mark the center of the tapered-head bolt.


c.

Using a 3 to 4 mm (0.119 to 0.157 in.) drill, drill a hole in the bolt.


d.
C322180

Using a screw extractor, remove the bolt and steering lock actuator assembly from the steering column assembly.


Hide 89650 8.REMOVE POWER STEERING ECU ASSEMBLY (for LHD)

Hide 45254B 9.REMOVE ELECTRIC POWER STEERING MOTOR SHAFT DAMPER (for LHD)

Hide 89650 10.REMOVE POWER STEERING ECU ASSEMBLY (for RHD)

Hide 45254B 11.REMOVE ELECTRIC POWER STEERING MOTOR SHAFT DAMPER (for RHD)