Home › Engine / Hybrid System › 3ZR-FAE (ENGINE CONTROL) › SFI SYSTEM
RM32H0E _51 Engine / Hybrid System _059607 3ZR-FAE ENGINE CONTROL _0292315 SFI SYSTEM J

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION


When the engine is cranked, the ST NO. 1 relay drive signal output from the certification ECU (smart key ECU assembly)*1 or ignition or starter switch assembly*2 is input into the STA terminal of the ECM, and the NE signal generated by the crankshaft position sensor is also input into the NE+ terminal. The ECM interprets that the engine is cranked, and turns transistor Tr1 in the ECM internal circuit on. Current flows to the C/OPN relay by turning Tr1 on. Then, the fuel pump operates.

While the NE signal is input into the ECM with the engine running, the ECM turns Tr1 on continuously.

*1: w/ Entry and Start System

*2: w/o Entry and Start System


WIRING DIAGRAM

A384874E06
6.094,5.052 6.708,5.25 0.615,0.198 10 false MREL 6.073,3.469 6.385,3.667 0.313,0.198 10 false FC 5.719,5.167 6.177,5.365 0.458,0.198 10 false A38 5.76,3.573 6.073,3.771 0.313,0.198 10 false A38 6.615,3.51 7.073,3.708 0.458,0.198 10 false Tr1 6.083,6 6.542,6.198 0.458,0.198 10 false STA 6.073,6.75 6.531,6.948 0.458,0.198 10 false NE+ 3.625,6.125 5.323,6.531 1.698,0.406 10 false from Starter Signal Circuit 4.26,7.052 5.271,7.479 1.01,0.427 10 false from Crankshaft Position Sensor 3.167,7.698 5.01,8.115 1.844,0.417 10 false Fuel Suction Tube with Pump and Gauge Assembly 0.594,7.75 1.667,7.948 1.073,0.198 10 false Battery 4.521,3.833 5.292,4.031 0.771,0.198 10 false C/OPN 1.865,5.417 2.958,5.688 1.094,0.271 10 false EFI-MAIN NO. 1 0.406,4.875 1.406,5.25 1,0.375 10 false EFI-MAIN NO. 1 1.906,3.24 3.063,3.833 1.156,0.594 10 false Integration Relay 1.917,3.042 2.229,3.24 0.313,0.198 10 false 1A 3.135,3.74 4.104,4.115 0.969,0.375 10 false ECU-IG2 NO. 1 5.75,3.385 6.063,3.583 0.313,0.198 10 false 41 6.146,0.281 6.76,0.479 0.615,0.198 10 false IG1D 5.813,0.177 6.063,0.375 0.25,0.198 10 false 17 5.208,0.844 7.156,1.458 1.948,0.615 10 false Certification ECU (Smart Key ECU Assembly)*1 5.229,0.698 5.688,0.896 0.458,0.198 10 false F1 1.781,0.667 2.24,0.865 0.458,0.198 10 false F12 1.792,0.844 3.708,1.375 1.917,0.531 10 false Ignition or Starter Switch Assembly*2 1.99,0.188 2.448,0.385 0.458,0.198 10 false AM1 3.094,0.188 3.552,0.385 0.458,0.198 10 false IG1 3.406,0.198 3.583,0.448 0.177,0.25 10 false 8 1.813,0.177 1.969,0.375 0.156,0.198 10 false 5 3.677,0.198 3.99,0.396 0.313,0.198 10 false *2 4.792,0.208 5.104,0.406 0.313,0.198 10 false *1 1.177,0.427 1.635,0.625 0.458,0.198 10 false AM2 0.438,1.083 1.208,1.281 0.771,0.198 10 false J/B-B 0.406,1.625 0.719,1.823 0.313,0.198 10 false *2 0.75,2.271 1.479,2.604 0.729,0.333 10 false IG2-MAIN 1.979,2.052 2.292,2.25 0.313,0.198 10 false 10 1.979,2.396 2.156,2.656 0.177,0.26 10 false 8 2.115,2.719 2.75,3.01 0.635,0.292 10 false IG2 NO. 1 2.771,2.375 2.927,2.573 0.156,0.198 10 false 7 2.76,2.052 2.906,2.229 0.146,0.177 9 false 9 0.406,5.969 1.781,6.167 1.375,0.198 10 false BATT MAIN 3.177,7.469 3.635,7.667 0.458,0.198 10 false M14 5.729,6.125 6.188,6.323 0.458,0.198 10 false A38 5.74,6.875 6.094,7.125 0.354,0.25 10 false C63 5.708,7.458 6.167,7.656 0.458,0.198 10 false C63 5.76,4.969 6.073,5.167 0.313,0.198 10 false 46 5.74,5.906 6.052,6.104 0.313,0.198 10 false 29 5.729,6.646 6.188,6.844 0.458,0.198 10 false 114 5.719,7.26 6.177,7.458 0.458,0.198 10 false 113 2.833,7.771 2.99,7.969 0.156,0.198 10 false E 2.854,7.979 3.01,8.177 0.156,0.198 10 false 5 2.844,7.219 3,7.417 0.156,0.198 10 false B 2.865,7.021 2.969,7.271 0.104,0.25 10 false 4 0.604,8.125 2.656,8.531 2.052,0.406 10 false *1: w/ Entry and Start System 0.625,8.49 2.656,8.823 2.031,0.333 10 false *2: w/o Entry and Start System 4.313,3.01 4.469,3.208 0.156,0.198 10 false 5 1.938,4.604 2.094,4.802 0.156,0.198 10 false 5 5.031,3.031 5.188,3.229 0.156,0.198 10 false 3 2.656,4.604 2.813,4.802 0.156,0.198 10 false 3 4.333,3.479 4.49,3.677 0.156,0.198 10 false 1 2.667,5.063 2.823,5.26 0.156,0.198 10 false 1 5.01,3.49 5.167,3.688 0.156,0.198 10 false 2 1.927,5.063 2.083,5.26 0.156,0.198 10 false 2 6.073,7.375 6.531,7.573 0.458,0.198 10 false NE- 6.313,8.021 6.771,8.219 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP/SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

e.

Check whether the fuel pump operating sound occurs when performing the Active Test on the GTS.

Result:
Result Proceed to
Fuel pump operating sound does not occur A
Fuel pump operating sound occurs B




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF C/OPN RELAY)

B

10.READ VALUE USING GTS (STARTER SIGNAL)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF C/OPN RELAY)
a.
A384879C01
0.146,0.063 0.458,0.26 0.313,0.198 10 false *1 0.292,1.51 0.604,1.708 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 C/OPN Relay Holder


Remove the C/OPN relay from the No. 1 engine room relay block.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (C/OPN relay holder) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT C/OPN RELAY

NG

9.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - NO. 1 INTEGRATION RELAY)
3.INSPECT C/OPN RELAY

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - ECM)

NG

REPLACE C/OPN RELAY

4.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - ECM)
a.

Remove the C/OPN relay from the No. 1 engine room relay block.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (C/OPN relay holder) - A38-41 (FC) Always Below 1 Ω
2 (C/OPN relay holder) or A38-41 (FC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (C/OPN RELAY - ECM)

5.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP)
a.

Remove the C/OPN relay from the No. 1 engine room relay block.


b.

Disconnect the Fuel Suction Tube with Pump and Gauge Assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (C/OPN relay holder) - M14-4 (B) Always Below 1 Ω
3 (C/OPN relay holder) or M14-4 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (C/OPN RELAY - FUEL PUMP)

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)
a.

Disconnect the M14 Fuel Suction Tube with Pump and Gauge Assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M14-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL PUMP - BODY GROUND)

7.INSPECT FUEL PUMP
a.

Inspect fuel pump.

Click hereEngine / Hybrid System>3ZR-FAE (FUEL)>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - EFI-MAIN NO. 1 RELAY)

NG

8.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - EFI-MAIN NO. 1 RELAY)
a.

Remove the C/OPN relay and EFI-MAIN NO. 1 relay from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (C/OPN relay holder) - 3 (EFI-MAIN NO. 1 relay holder) Always Below 1 Ω
5 (C/OPN relay holder) or 3 (EFI-MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (C/OPN RELAY - EFI-MAIN NO. 1 RELAY)

9.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - NO. 1 INTEGRATION RELAY)
a.

Remove the C/OPN relay from the No. 1 engine room relay block.


b.

Disconnect the 1A integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (C/OPN relay holder) - 1A-9 Always Below 1 Ω
1 (C/OPN relay holder) or 1A-9 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (C/OPN RELAY - NO. 1 INTEGRATION RELAY)

10.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the result when the ignition switch is ON and the engine starts.

OK:
Condition Starter Signal
Ignition switch ON OFF
Engine Started ON



Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (ENGINE SPEED)

NG

11.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

e.

Read the values displayed on the GTS while cranking.

OK:

Values are displayed continuously.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

CHECK CRANKSHAFT POSITION SENSOR CIRCUIT