Home › Drivetrain › CLUTCH › CLUTCH PEDAL (for RHD)
RM32H0E _52 Drivetrain _059611 CLUTCH _0292332 CLUTCH PEDAL(for RHD) A

CLUTCH  CLUTCH PEDAL(for RHD)  INSTALLATION  


PROCEDURE

Hide 31321 1.INSTALL CLUTCH PEDAL PAD

a.

Install the clutch pedal pad to the clutch pedal sub-assembly.


Hide 31453B 2.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSH

a.

Install a new clutch master cylinder push rod clevis bush to the clutch pedal sub-assembly.

NOTICE:

Install the clutch master cylinder push rod clevis bush from the left side of the vehicle.



b.
C366506C01
0,0 0,0 false
V100135

MP Grease


Apply MP grease to the inside of the clutch master cylinder push rod clevis bush.


Hide 31324A 3.INSTALL CLUTCH PEDAL SHAFT COLLAR

a.
C366508C01
0,0 0,0 false
V100135

MP Grease


Apply MP grease to both sides of 2 new clutch pedal bushes.


b.

Install the 2 clutch pedal bushes and clutch pedal shaft collar to the clutch pedal sub-assembly.


Hide 4.INSTALL CLUTCH PEDAL TURNOVER BUSH

a.
C366510C01
0,0 0,0 false
V100135

MP Grease


Apply MP grease to the inside of the clutch pedal turnover bush and install the bush to the clutch pedal sub-assembly.


Hide 31353 5.INSTALL CLUTCH PEDAL SPRING HOLDER

a.
C366512C01
0,0 0,0 false
V100135

MP Grease


Apply MP grease to the contact surface of the clutch pedal spring holder and install the clutch pedal spring holder to the clutch pedal support sub-assembly.


Hide 31301 6.INSTALL CLUTCH PEDAL SUB-ASSEMBLY

a.

Install the clutch pedal sub-assembly to the clutch pedal support sub-assembly with the bolt and nut.

Torque:
36.8 N*m (375 kgf*cm, 27 ft.*lbf)

NOTICE:
·

Install the bolt from the right side of the vehicle.

·

Turn the nut while holding the bolt.




Hide 31301A 7.INSTALL CLUTCH PEDAL SPRING

a.

Move the pedal to the full stroke position.


b.

Install the clutch pedal spring to the clutch pedal assembly.


Hide 89280 8.INSTALL CLUTCH PEDAL STROKE SENSOR ASSEMBLY

Hide 88280A 9.INSTALL CLUTCH SWITCH ASSEMBLY

Hide 10.INSTALL CLUTCH PEDAL SUPPORT ASSEMBLY

a.

Install the clutch pedal support assembly to the clutch master cylinder assembly with the 2 nuts.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


b.

Install the clutch pedal support assembly to the body with the 2 nuts.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


c.

Engage the 3 clamps to the clutch pedal support assembly.


d.

Connect the 2 connectors.


Hide 31410 11.CONNECT CLUTCH MASTER CYLINDER ASSEMBLY

a.
C245271C01
0,0 3.427,0 false
V100135

MP Grease


Apply MP grease to the clevis pin.


b.

Connect the clutch master cylinder assembly to the clutch pedal sub-assembly with the clevis pin.

NOTICE:

Install the clevis pin from the left side of the vehicle.



c.

Install a new clip to the clevis pin.


Hide 55401E 12.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY