Home › Drivetrain › K313F (MULTIDRIVE / CVT) › OIL PAN › 2016.10–2019.09
RM32H0E _52 Drivetrain _059618 K313F MULTIDRIVE / CVT _0292478 OIL PAN A

K313F MULTIDRIVE / CVT  OIL PAN  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the transaxle oil (CVT) pan sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51444A 2.REMOVE REAR ENGINE UNDER COVER LH

Hide 3.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID

a.
C362025

Remove the refill plug and gasket from the rear transaxle case.


b.
C362026

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle oil (CVT) pan sub-assembly and drain the fluid.


c.
C364033C01
2.365,0.656 2.583,0.844 true 2.198,0.51 2.51,0.708 0.313,0.198 10 false *1
*1 No. 1 Transmission Oil Filler Tube


Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle oil (CVT) pan sub-assembly and drain the fluid.


d.

Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle oil (CVT) pan sub-assembly.

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


e.

Using a 6 mm hexagon socket wrench, temporarily install the overflow plug and gasket to the transaxle oil (CVT) pan sub-assembly.

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the fluid level.



f.

Temporarily install the refill plug and gasket to the rear transaxle case.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.



Hide 35106L 4.REMOVE TRANSAXLE OIL (CVT) PAN SUB-ASSEMBLY

a.
C326859

Remove the 16 bolts, transaxle oil (CVT) pan sub-assembly and transaxle oil pan (CVT) gasket from the transaxle case.


b.

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle oil (CVT) pan sub-assembly.


c.

Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle oil (CVT) pan sub-assembly.


Hide 35394D 5.REMOVE OIL CLEANER (CVT) MAGNET

a.
C326863C01
0.438,1.125 1.979,0.854 true 2.177,1.479 0.427,1.125 0.427,1.125 1.146,0.781 true 0.26,1.052 0.573,1.208 0.313,0.156 10 false *1
*1 Oil Cleaner (CVT) Magnet


Remove the 3 oil cleaner (CVT) magnets from the transaxle oil (CVT) pan sub-assembly.


b.

Clean off any metal particles adhered to the 3 oil cleaner (CVT) magnets.


c.

Clean the transaxle oil (CVT) pan sub-assembly and remove any metal particles, sludge, etc.


Hide 35330D 6.REMOVE OIL STRAINER ASSEMBLY

HINT:

Perform this procedure only when replacement of the oil strainer assembly is necessary.


a.
C305428

Remove the 3 bolts and oil strainer assembly from the transmission valve body assembly.


b.
C305829

Remove the O-ring from the oil strainer assembly.