Home › Engine / Hybrid System › 8NR-FTS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059498 8NR-FTS ENGINE MECHANICAL _0291517 ENGINE ASSEMBLY A

8NR-FTS ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)*1
Pre-collision syatem
Initialize back door lock Power door lock control system (Click here)
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)*2 Stop and start system (Click here)
·

Replacement of engine assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF thermal Degradation Estimate" is not estimated correctly for K313
(Click here)
for K313F
(Click here)
Front wheel alignment adjustment Perform the following procedures in the order shown:
1.

Clear zero point calibration data and store system information

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information


·

VSC disabled or malfunctions

·

DTCs are stored

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)


CAUTION:
·
A340377C22
0.542,1.115 0.958,1.115 false 0.344,1.01 0.656,1.208 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the engine lifter


Because the weight of the engine with transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the engine lifter could drop and components could fall down.


·
A340359C12
0.375,1.135 0.75,1.281 true 0.135,1.031 0.448,1.229 0.313,0.198 10 false *a
*a High temperature areas


Do not touch the engine or exhaust manifold converter sub-assembly when they are hot.

·

Touching the engine or exhaust manifold converter sub-assembly when they are hot could result in burns.


·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Air Conditioning System)

Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 5.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 6.REMOVE FRONT WHEELS

Hide 51441 7.REMOVE NO. 1 ENGINE UNDER COVER

a.
A390450

Remove the 4 bolts, 4 screws, 4 clips and No. 1 engine under cover from the vehicle.


Hide 51444A 8.REMOVE REAR ENGINE UNDER COVER LH

a.
A390452

Remove the 6 clips and rear engine under cover LH from the vehicle.


Hide 51443C 9.REMOVE REAR ENGINE UNDER COVER RH

a.
A390451

Remove the 6 clips and rear engine under cover RH from the vehicle.


Hide 12.DRAIN COOLANT (for Intercooler)

Hide 13.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)

Hide 14.DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle)

·

w/o Stop and Start System:

Click hereGeneral>MAINTENANCE>EC6A MANUAL TRANSAXLE OIL>REPLACEMENT

·

Hide 15.DRAIN TRANSFER OIL (for AWD)

Hide 16.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55737B 17.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 55735A 18.REMOVE WATER GUARD PLATE LH

Hide 55736D 19.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735C 20.REMOVE COWL BODY MOUNTING REINFORCEMENT RH

Hide 55701J 21.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 22.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 28800 23.REMOVE BATTERY

Hide 53141F 24.REMOVE RADIATOR COVER

Hide 17751 25.REMOVE NO. 1 AIR CLEANER INLET

Hide 17705 26.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

a.
A390456C02
1.229,2.792 0.719,2.552 0.719,2.552 1.271,2.365 true 2.781,3 3.031,3.104 3.031,3.104 2.854,2.406 true 0.427,2.427 0.656,2.635 0.229,0.208 10 true *2 3.042,3.156 3.271,3.365 0.229,0.208 10 true *1
*1 Air Cleaner Cap Sub-assembly Clamp
*2 Guide


Disconnect the mass air flow meter connector.


b.

Disengage the clamp from the air cleaner cap sub-assembly.


c.

Disengage the 2 air cleaner cap sub-assembly clamps.


d.

Disengage the 2 guides to separate the air cleaner cap sub-assembly from the air cleaner case sub-assembly.


e.

Loosen the hose clamp and remove the air cleaner cap with air cleaner hose from the No. 1 inlet air duct sub-assembly.


Hide 17701 27.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A390457

Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.


b.
A390458

Remove the 2 bolts and air cleaner case sub-assembly from the vehicle.


Hide 29.DISCONNECT WIRE HARNESS

a.
A394171

Remove the 2 bolts to separate the engine wire from the vehicle.


b.
A390461

Remove the bolt and nut to separate the engine wire from the battery clamp sub-assembly.


c.
A392285

Remove the 3 nuts to separate the engine wire from the positive (+) battery terminal.


d.
A392286C01
0.125,0.167 0.417,0.417 0.292,0.25 12 true *A 0.167,2.583 0.458,2.833 0.292,0.25 12 true *B
*A for CVT
*B for Manual Transaxle


Remove the bolt to separate the engine wire from the transaxle assembly.


Hide 74404A 30.REMOVE BATTERY CLAMP SUB-ASSEMBLY

a.
A392287

Disengage the clamp to separate the engine wire from the battery clamp sub-assembly.


b.

Remove the 3 bolts and battery clamp sub-assembly from the vehicle.


Hide 16571C 31.DISCONNECT NO. 1 RADIATOR HOSE

A393647

a.

Slide the clip and disconnect the No. 1 radiator hose from the water outlet.


Hide 16572D 32.DISCONNECT NO. 2 RADIATOR HOSE

a.
A393646

Slide the clip and disconnect the No. 2 radiator hose from the water inlet with thermostat sub-assembly.


Hide 16551C 33.DISCONNECT NO. 1 INTERCOOLER COOLING WATER HOSE

Hide 16554C 34.DISCONNECT NO. 4 INTERCOOLER COOLING WATER HOSE

Hide 33820B 35.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for CVT)

Hide 44750 37.DISCONNECT UNION TO CONNECTOR TUBE HOSE

Hide 23829A 38.DISCONNECT FUEL VAPOR FEED HOSE

a.
A392288

Slide the clip and disconnect the fuel vapor feed hose from the fuel vapor feed pipe.


Hide 23901 41.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 88703 42.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY (w/ Air Conditioning System)

Hide 88704 43.DISCONNECT SUCTION HOSE SUB-ASSEMBLY (w/ Air Conditioning System)

Hide 44.SECURE STEERING WHEEL ASSEMBLY

Hide 45259A 45.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 46.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45025D 47.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 58166 48.REMOVE FRONT FLOOR COVER LH (w/ Cover)

Hide 58165B 49.REMOVE FRONT FLOOR COVER RH (w/ Cover)

HINT:

Use the same procedure as for the LH side.


Hide 57533B 50.REMOVE FRONT FLOOR CENTER BRACE (for 2WD)

Hide 57533B 51.REMOVE FRONT FLOOR CENTER BRACE (for AWD)

Hide 17410 52.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (for 2WD)

Hide 17420K 53.REMOVE NO. 2 CENTER EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (for AWD)

Hide 17410 54.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for AWD)

Hide 37100 55.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for AWD)

Hide 31481A 59.DISCONNECT NO. 1 CLUTCH HOSE (for Manual Transaxle)

a.
A392290

Using a 10 mm union nut wrench, disconnect the bleeder clutch release tube from the No. 1 clutch hose.


b.

Remove the clip and disconnect the No. 1 clutch hose from the clutch flexible hose bracket.


Hide 51108A 60.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 61.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle and front suspension crossmember sub-assembly level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.




b.
A392291

Remove the 2 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.


c.
A392292C01
0.021,0.031 0.385,0.333 0.365,0.302 12 true *A 0,2.49 0.375,2.813 0.375,0.323 12 true *B
*A for CVT
*B for Manual Transaxle


Remove the bolt and nut and separate the engine mounting insulator LH from the engine mounting bracket LH.

NOTICE:

While holding the nut in place, loosen the bolt.



d.
A392289

Remove the 6 bolts to separate the front suspension crossmember sub-assembly from the vehicle.


e.

Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.




Hide 63.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A392293

Disengage the 3 clamps.


b.

Remove the nut to separate the engine wire from the wire harness clamp bracket.


c.

Remove the bolt and wire harness clamp bracket from the cylinder head sub-assembly.


Hide 64.INSTALL ENGINE HANGERS

a.
A351514C04
0.406,1.604 0.75,1.604 true 2.531,1.073 2.875,1.073 true 0.219,1.542 0.531,1.698 0.313,0.156 10 false *1 2.958,1.01 3.271,1.167 0.313,0.156 10 true *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger
V100135

Bolt


Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-47060
No. 2 Engine Hanger 12282-47030
Bolt 91552-81030



b.

Using an engine sling device and engine lift, secure the engine assembly with transaxle.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




Hide 12372A 65.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A392296C01
0.021,0.031 0.396,0.323 0.375,0.292 12 true *A 0.021,2.469 0.438,2.771 0.417,0.302 12 true *B
*A for CVT
*B for Manual Transaxle


Remove the 4 bolts, nut and engine mounting insulator LH from the vehicle.


Hide 12305 66.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH (w/ Air Conditioning System)

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A392294

Remove the 2 bolts and No. 2 earth wire from the engine mounting insulator sub-assembly RH and vehicle.


b.
A392295

Remove the bolt, nut and disconnect the air conditioner tube and accessory.


c.

Remove the 2 bolts, nut and engine mounting insulator sub-assembly RH from the vehicle.


Hide 12305 67.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH (w/o Air Conditioning System)

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A395542

Remove the 2 bolts and No. 2 earth wire from the engine mounting insulator sub-assembly RH and vehicle.


b.
A395543

Remove the 2 bolts, nut and engine mounting insulator sub-assembly RH from the vehicle.


Hide 68.REMOVE WATER HOSE (for CVT)

a.
A392297

Disengage the 3 clamps from the engine assembly with transaxle.


b.

Slide the 5 clips and remove the water hose from the engine assembly with transaxle.


Hide 69.REMOVE WATER HOSE (for Manual Transaxle)

a.
A392298

Disengage the 3 clamps from the engine assembly with transaxle.


b.

Slide the 3 clips and remove the water hose from the engine assembly with transaxle.


Hide 28100 70.REMOVE STARTER ASSEMBLY

Hide 11363A 71.REMOVE FLYWHEEL HOUSING SIDE COVER

a.
A394157

Remove the flywheel housing side cover from the cylinder block sub-assembly.


Hide 82121 72.REMOVE ENGINE WIRE

a.

Disconnect all the clamps and connectors and remove the engine wire from the engine assembly with transaxle.


Hide 32101B 75.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)

Hide 31250 76.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)

·

w/o Stop and Start System:

Click hereDrivetrain>CLUTCH>CLUTCH UNIT (for EC6A)>REMOVAL

·

w/ Stop and Start System:

Click hereDrivetrain>CLUTCH>CLUTCH UNIT (for EC69)>REMOVAL


Hide 13405 77.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

Hide 16361A 78.REMOVE FAN AND GENERATOR V BELT

Hide 16620 79.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A351532

Remove the 2 bolts and V-ribbed belt tensioner assembly from the timing chain cover assembly.


Hide 88310 81.REMOVE COMPRESSOR WITH PULLEY ASSEMBLY (w/ Air Conditioning System)

Hide 82.REMOVE NO. 1 IDLER PULLEY (w/o Air Conditioning System)

HINT:

Perform this procedure only when replacement of the No. 1 idler pulley is necessary.


a.
A361744

Remove the bolt and No. 1 idler pulley with the 2 idler pulley cover plate from the idler pulley bracket.


Hide 16603 83.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY (w/o Air Conditioning System)

a.
A361745C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt and 2 nuts.


b.

Remove the No. 1 idler pulley sub-assembly.


c.
A361875

Using an E8 "TORX" socket wrench, remove the 2 stud bolts.


Hide 84.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.

Install the engine assembly to an engine stand.


Hide 85.REMOVE ENGINE HANGERS

a.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger.