Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR › 2016.10–2018.05
RM32H0E _59 Vehicle Exterior _059645 MIRROR (EXT) _0292588 OUTER REAR VIEW MIRROR A

MIRROR (EXT)  OUTER REAR VIEW MIRROR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.INSTALL OUTER MIRROR RETRACTOR (for LED Type Turn Signal Light)

a.
B536774

Install a new retractor assembly to a new wire harness as shown in the illustration.


b.
B536775

Install the retractor assembly with the screw.


c.
B536771

Connect the connector.


d.

Engage the guides.


e.
B536770

Install the reinforcement with the 4 screws.


f.
B536769

Install the cover base A to the wire harness.


g.

Install the cover base A with 3 new screws.

NOTICE:
·

Check that the wire harness is not caught.

·

Do not damage the screw coating.

·

Securely tighten the screws so that they will not come loose.




h.
B536767

Install the unit drive assembly with the 3 screws.


i.
B536766

Connect the connector.


j.
B536768

Engage the guides and claws to install a new cover base B.


k.
B536765

Install a new seal to the wire harness.


l.

Engage the guides to install the seal.

NOTICE:

Do not make gaps between the cover base and seal.



m.
B536764

Engage the guides to install the foam.


n.
B536763C06
1.563,1.229 1.854,0.896 true 1.365,1.146 1.583,1.354 0.219,0.208 10 false *a
*a Vinyl Tape


Install the vinyl tape as shown in the illustration.


o.

Assemble the connector housing.

i.

Pull the retainer and release the lock of connector housing.

B534392C04
2.51,1.313 2.771,1.052 false 2.813,1.927 2.521,1.573 false 1.385,2.052 1.146,1.729 false 5.698,2.031 6.156,1.688 false 2.802,0.927 3.115,1.125 0.313,0.198 10 false *2 2.865,1.885 3.177,2.083 0.313,0.198 10 false *2 3.635,0.51 3.948,0.708 0.313,0.198 10 false *c 0.271,0.719 0.583,0.917 0.313,0.198 10 false *a 1.438,2.021 1.75,2.219 0.313,0.198 10 false *1 5.635,0.573 5.948,0.771 0.313,0.198 10 false *b 5.51,1.969 5.823,2.167 0.313,0.198 10 false *1
*1 Retainer *2 Terminal
*a Unlock Position *b Lock Position
*c Front view of connector - -



ii.

While referring to the chart below, insert the terminals of the wire harness into the back of a new connector housing until they lock.

Wire Harness Color
1 2 3 4 5 6 7 8
White - Green Brown - White - - - Gray - Red
9 10 11 12 13 14 15 16
Red Black Blue Black - Red - - - Pink

NOTICE:
·

When inserting the terminals of the wire harness, compare the new connector with the connector that was cut off during removal and make sure that the arrangement of the wire colors of the terminals is the same as before.

·

If the insertion position of the terminals is mistaken, the vehicle side control system may be damaged.

·

Check that the terminals are securely locked and cannot be removed.




iii.

Push the retainer and lock the connector.



Hide 81730B 2.INSTALL SIDE TURN SIGNAL LIGHT BULB (for Bulb Type Turn Signal Light)

Hide 3.INSTALL DOOR MIRROR FOOT LIGHT (for LED Type Turn Signal Light)

Hide 4.INSTALL SIDE TURN SIGNAL LIGHT ASSEMBLY (for LED Type Turn Signal Light)

Hide 87945 5.INSTALL OUTER MIRROR COVER (for LED Type Turn Signal Light)

Hide 87945 6.INSTALL OUTER MIRROR COVER (for Bulb Type Turn Signal Light)

Hide 87961 7.INSTALL OUTER MIRROR (for LED Type Turn Signal Light)

Hide 87961 8.INSTALL OUTER MIRROR (for Bulb Type Turn Signal Light)