Home › Engine / Hybrid System › 3ZR-FAE (ENGINE MECHANICAL) › CAMSHAFT
RM32H0E _51 Engine / Hybrid System _059726 3ZR-FAE ENGINE MECHANICAL _0292813 CAMSHAFT A

3ZR-FAE ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the camshaft housing sub-assembly, camshaft timing gear assembly or camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 13750 1.INSTALL VALVE LASH ADJUSTER ASSEMBLY

Hide 13801 2.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 11103 3.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A319919C01
1.063,0.573 1.281,0.156 1.281,0.156 1.479,0.156 false 0.24,0.708 0.5,0.708 false 1.302,1.323 1.563,1.323 false 1.833,0.76 2.094,0.76 false 3.01,1.375 3.198,1.5 3.198,1.5 3.198,1.667 false 2.698,0.469 2.854,0.208 2.854,0.208 3.052,0.208 false 0.063,0.625 0.375,0.823 0.313,0.198 10 false *2 1.51,0.073 1.823,0.271 0.313,0.198 10 false *1 1.604,1.24 1.917,1.438 0.313,0.198 10 false *3 1.677,0.677 1.99,0.875 0.313,0.198 10 false *2 3.135,1.698 3.396,2 0.26,0.302 10 false *3 3.115,0.115 3.427,0.313 0.313,0.198 10 false *1 0.75,1.771 1.063,1.969 0.313,0.198 10 false *a 2.438,1.792 2.75,1.99 0.313,0.198 10 false *b
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Stem Cap
*3 Valve Lash Adjuster Assembly
*a Correct
*b Incorrect


Check that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


b.
A206178C13
1.771,2.354 1.885,2.917 1.885,2.917 2.063,2.917 false 0.458,2.885 0.771,3.219 0.313,0.333 10 false A 0.396,0.344 0.865,0.854 0.469,0.51 10 false B 2.104,2.833 2.479,3.094 0.375,0.26 10 false *a
*a Continuous line


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal Packing Application Chart:
Area Seal Packing Diameter Application length
Continuous line 3.5 to 4.5 mm (0.138 to 0.177 in.) -
(A) 8.0 mm (0.315 in.) 15 mm (0.591 in.)
(B) 7.0 mm (0.276 in.) 15 mm (0.591 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the camshaft housing sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




c.
A289825N02
1.646,1.948 2.021,2.302 0.375,0.354 10 1 0.958,1.375 1.333,1.729 0.375,0.354 10 8 0.365,1.323 0.74,1.677 0.375,0.354 10 14 0.594,1.323 0.969,1.677 0.375,0.354 10 17 1.427,1.365 1.802,1.719 0.375,0.354 10 2 1.896,1.375 2.271,1.729 0.375,0.354 10 5 2.313,1.375 2.688,1.729 0.375,0.354 10 11 2.563,1.948 2.938,2.302 0.375,0.354 10 10 2.094,1.958 2.469,2.313 0.375,0.354 10 4 1.188,1.979 1.563,2.333 0.375,0.354 10 7 0.063,2.167 0.438,2.521 0.375,0.354 10 13 0.365,3.156 0.74,3.51 0.375,0.354 10 15 0.969,3.104 1.344,3.458 0.375,0.354 10 9 1.427,3.094 1.802,3.448 0.375,0.354 10 3 1.906,3.104 2.281,3.458 0.375,0.354 10 6 2.313,3.094 2.688,3.448 0.375,0.354 10 12 2.854,2.198 3.229,2.552 0.375,0.354 10 16

Set the camshaft and No. 2 camshaft as shown in the illustration.


d.

Install the camshaft housing sub-assembly with the 17 bolts and tighten them in the order shown in the illustration.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)

NOTICE:
·

After installing the camshaft housing sub-assembly, make sure that the cam lobes are positioned as shown in the illustration.

·

If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly, clean the installation surfaces, and reapply seal packing.

·

If the camshaft housing sub-assembly is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.

·

After installing the camshaft housing sub-assembly, wipe off any seal packing that seeped out from between the camshaft housing sub-assembly and cylinder head sub-assembly.



HINT:

Perform "Inspection After Repair" after replacing the camshaft housing sub-assembly.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 13070A 4.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A215318C04
1.448,1.021 1.031,0.219 false 1.156,1 0.521,1.646 false 0.917,0.021 1.104,0.177 0.188,0.156 10 *1 0.375,1.677 0.563,1.833 0.188,0.156 10 *a
*1 Straight Pin
*a Pin Hole


Fit the camshaft timing exhaust gear assembly and No. 2 camshaft together by aligning the pin hole and straight pin.

NOTICE:

Do not forcibly push in the camshaft timing exhaust gear assembly. This may cause the No. 2 camshaft straight pin tip to damage the installation surface of the camshaft timing exhaust gear assembly.



b.

Lightly press the camshaft timing exhaust gear assembly against the No. 2 camshaft and turn the camshaft timing exhaust gear assembly. Push further at the position where the straight pin enters the pin hole.

NOTICE:

Be sure not to turn the camshaft timing exhaust gear assembly in the retard direction (clockwise).



c.
A146267C10
2.771,0.75 2.604,0.75 2.604,0.75 1.406,1.01 false 1.521,0.177 1.323,0.177 1.323,0.177 1.063,0.906 false 1.573,0.115 1.885,0.271 0.313,0.156 10 *1 2.844,0.688 3.156,0.844 0.313,0.156 10 *a 1.396,0.552 1.708,0.708 0.313,0.156 10 *b 1.406,1.938 1.719,2.094 0.313,0.156 10 *c
*1 Camshaft Timing Exhaust Gear Assembly
*a Flange
*b Gap
*c No Gap


Check that there is no gap between the camshaft timing exhaust gear assembly and No. 2 camshaft flange.


d.
A165297

Tighten the bolt with the camshaft timing exhaust gear assembly secured in place.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


e.

Check the camshaft timing exhaust gear assembly lock.

i.

Make sure that the camshaft timing exhaust gear assembly is locked.

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Hide 13050 5.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

a.
A146265C26
2.26,0.573 2.146,0.573 2.146,0.573 1.938,1.083 false 1.313,1.031 1.479,0.24 1.479,0.24 1.635,0.24 false 2.302,0.51 2.469,0.677 0.167,0.167 10 false *1 1.667,0.156 1.875,0.333 0.208,0.177 10 false *a
*1 Straight Pin
*a Key Groove


Put the camshaft timing gear assembly and camshaft together with the straight pin and key groove misaligned as shown in the illustration.

NOTICE:

Do not forcibly push in the camshaft timing gear assembly. This may cause the camshaft straight pin tip to damage the installation surface of the camshaft timing gear assembly.



b.
A270928C04
0.813,1.396 1,1.917 1,1.917 1.167,1.917 true 0.802,0.583 0.802,0.167 0.802,0.167 0.969,0.167 true 1.01,0.063 1.323,0.219 0.313,0.156 10 false *1 1.208,1.833 1.521,1.99 0.313,0.156 10 false *b 0.208,0.333 0.521,0.49 0.313,0.156 10 false *a 2.583,0.698 2.844,1.073 0.26,0.375 10 false A
*1 Straight Pin
*a View A
*b Key Groove


Turn the camshaft timing gear assembly as shown in the illustration while pushing it gently against the camshaft. Push further at the position where the straight pin fits into the key groove.

NOTICE:

Do not turn the camshaft timing gear assembly in the retard direction (clockwise).



c.
A146267C13
2.771,0.75 2.604,0.75 2.604,0.75 1.406,1.01 false 1.49,0.177 1.292,0.177 1.292,0.177 1.031,0.906 false 1.552,0.083 1.865,0.24 0.313,0.156 10 *1 2.854,0.688 3.167,0.844 0.313,0.156 10 *a 1.417,0.552 1.729,0.708 0.313,0.156 10 *b 1.427,1.969 1.74,2.125 0.313,0.156 10 *c
*1 Camshaft Timing Gear Assembly
*a Flange
*b Gap
*c No Gap


Check that there is no gap between the camshaft timing gear assembly and camshaft flange.


d.
A165296

Tighten the bolt with the camshaft timing gear assembly secured in place.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


e.
A165299C06
0,0 0,0 false
V100135

Lock


Check that the camshaft timing gear assembly can move in the retard direction (clockwise) and locks in the most retarded position.

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 13506 6.INSTALL CHAIN SUB-ASSEMBLY