Home › Engine / Hybrid System › 3ZR-FAE (LUBRICATION) › OIL PUMP
RM32H0E _51 Engine / Hybrid System _060036 3ZR-FAE LUBRICATION _0294094 OIL PUMP A

3ZR-FAE LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 15100 1.INSTALL OIL PUMP ASSEMBLY

a.

Install the oil pump assembly to the stiffening crankcase assembly with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 12102A 2.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

a.

Remove any remaining seal packing and be careful not to drop any oil on the contact surfaces of the cylinder block sub-assembly and No. 2 oil pan sub-assembly.


b.
A219124C08
0.448,1.917 0.729,1.625 false 0.375,1.292 0.615,1.604 0.24,0.313 10 false A 0.958,0.896 1.177,1.083 0.219,0.188 10 false B 0.677,2.24 1.031,2.479 0.354,0.24 10 false A-A 1.823,2.24 2.156,2.479 0.333,0.24 10 false B-B 0.344,2.344 0.594,2.552 0.25,0.208 10 false *b 2.219,2.302 3.094,2.458 0.875,0.156 10 false *c 0.313,1.969 0.76,2.281 0.448,0.313 10 false *a 0.375,0.896 0.594,1.083 0.219,0.188 10 false B 0.948,1.281 1.188,1.594 0.24,0.313 10 false A
*a Seal Packing Black
*b 6.0 mm (0.236 in.)
*c 3.0 to 4.5 mm (0.118 to 0.177 in.)


Apply seal packing in a continuous line as shown in the illustration.

Application Specification:
Area Seal Packing Diameter Distance from Center of Bolt Hole to Center of Seal Packing
(A) - (A) 3.0 to 4.5 mm (0.118 to 0.177 in.) 6.0 mm (0.236 in.)
(B) - (B) -


Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the No. 2 oil pan sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

·

Do not add engine oil for at least 2 hours after installing the No. 2 oil pan sub-assembly.




c.

Install the No. 2 oil pan sub-assembly with the 10 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13507 3.INSTALL NO. 2 CHAIN SUB-ASSEMBLY

a.

Temporarily install the crankshaft pulley bolt.


b.
A206151

Set the crankshaft timing gear key as shown in the illustration.


c.

Turn the oil pump drive shaft so that the cutout faces upward.


d.

Remove the crankshaft pulley bolt.


e.
A296326C04
1.5,1.802 1.083,1.583 1.083,1.583 0.917,1.583 false 1.594,1.927 2.177,2.094 2.177,2.094 2.344,2.094 true 1.906,4.167 2.125,4.417 2.125,4.417 2.25,4.417 false 1.844,3.438 2.333,3.083 2.333,3.083 2.583,3.083 true 1.75,2.417 2.198,2.667 2.198,2.667 2.417,2.667 true 1.177,3.844 1.396,3.844 1.396,3.844 1.844,4.01 true 0.969,3.781 1.177,3.979 0.208,0.198 10 false *b 2.385,2.021 2.583,2.219 0.198,0.198 10 false *b 0.729,1.51 0.927,1.708 0.198,0.198 10 false *a 2.302,4.354 2.49,4.531 0.188,0.177 10 false *a 2.469,2.604 2.656,2.792 0.188,0.188 10 false *1 2.625,3.01 2.823,3.208 0.198,0.198 10 false *2
*1 Oil Pump Drive Gear
*2 Oil Pump Drive Shaft Gear
*a Yellow Mark Plate
*b Timing Mark
V100135

Engine Front


Align the yellow mark plates with the timing mark of the oil pump drive gear and oil pump drive shaft gear as shown in the illustration.


f.

With the No. 2 chain sub-assembly around the oil pump drive gear and oil pump drive shaft gear, install the oil pump drive gear to the crankshaft and temporarily install the oil pump drive shaft gear to the oil pump drive shaft.


g.

Temporarily install the oil pump drive shaft gear nut.


h.

Install the chain damper spring to the chain tensioner plate, and then install the chain tensioner plate with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


i.
A206155N07
0.337,0.148 0.66,0.325 0.323,0.177 10 SST 0.724,0.216 0.87,0.216 0.87,0.216 1.48,0.474 false 1.189,0.587 0.87,0.216 false

Temporarily install the crankshaft pulley with the crankshaft pulley bolt.


j.

Using SST, hold the crankshaft pulley. Then tighten the oil pump drive shaft gear nut.

SST
09213-54015  09330-00021  

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

HINT:

Part number of installation bolt for SST (crankshaft pulley holding tool): 91551-00850 (quantity: 2)



k.

Remove SST, the crankshaft pulley bolt and crankshaft pulley.


Hide 13521 4.INSTALL CRANKSHAFT TIMING SPROCKET

a.
A309568C01
0,0 0,0 false
V100136

Engine Front


Install the crankshaft timing sprocket as shown in the illustration.


Hide 13561 5.INSTALL NO. 1 CHAIN VIBRATION DAMPER

Hide 6.SET NO. 1 CYLINDER TO TDC / COMPRESSION

Hide 13559 8.INSTALL CHAIN TENSIONER SLIPPER

Hide 9.CHECK NO. 1 CYLINDER TO TDC / COMPRESSION

Hide 11302 10.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.

Install a new gasket to the timing chain cover sub-assembly.

NOTICE:

Remove any oil from the contact surface.



b.

Install the engine water pump assembly to the timing chain cover sub-assembly with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Remove any remaining seal packing material.


d.

Clean the contact surfaces of the timing chain cover sub-assembly, camshaft housing sub-assembly, cylinder head sub-assembly, cylinder block sub-assembly and stiffening crankcase assembly, and confirm that no oil, moisture, or other foreign matter is on the surfaces.

A313808C02
0.802,0.198 1.115,0.354 0.313,0.156 10 false *a 4.01,0.188 4.323,0.344 0.313,0.156 10 false *b
*a Engine Side *b Timing Chain Cover Sub-assembly Side
V100145

Clean and degrease - -



e.

Install 2 new O-rings to the cylinder head sub-assembly.


f.

Install a new O-ring to the cylinder block sub-assembly.


g.
A283482

Apply seal packing to the engine unit as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Diameter:

5.0 mm (0.197 in.)


NOTICE:

Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.



h.

Apply seal packing in a continuous line to the timing chain cover sub-assembly as shown in the following illustration.

A296857C05
2.26,2.031 2.385,2.031 2.385,2.031 2.531,1.781 false 4.646,2.177 4.49,2.177 4.49,2.177 4.365,1.802 false 3.375,5.219 3.719,5.438 3.719,5.438 3.927,5.438 false 1.354,5.26 1.771,5.417 1.771,5.417 1.927,5.417 false 5.344,5.26 5.625,5.375 5.625,5.375 5.781,5.375 false 4.833,1.125 4.979,1.292 0.146,0.167 10 false J 2.188,2.208 2.333,2.375 0.146,0.167 10 false O 6.25,2.115 6.396,2.281 0.146,0.167 10 false M 1.51,1.156 1.656,1.323 0.146,0.167 10 false F 0.563,3.948 0.708,4.115 0.146,0.167 10 false I 0.823,2.042 0.969,2.208 0.146,0.167 10 false H 6.583,3.979 6.729,4.146 0.146,0.167 10 false N 5.229,1.917 5.375,2.083 0.146,0.167 10 false K 5.74,2.073 5.885,2.24 0.146,0.167 10 false L 2.135,1.01 2.281,1.177 0.146,0.167 10 false A 2.781,0.708 2.927,0.875 0.146,0.167 10 false A 1.188,1.938 1.333,2.104 0.146,0.167 10 false G 2.104,1.938 2.25,2.104 0.146,0.167 10 false D 4.688,2.083 4.833,2.25 0.146,0.167 10 false E 5.542,7.396 5.688,7.563 0.146,0.167 10 false B 2.156,7.094 2.302,7.26 0.146,0.167 10 false B 1.479,7.396 1.625,7.563 0.146,0.167 10 false B 4.875,7.094 5.021,7.26 0.146,0.167 10 false B 2.167,7.833 2.313,8 0.146,0.167 10 false C 1.438,7.833 1.583,8 0.146,0.167 10 false C 4.729,7.677 4.875,7.844 0.146,0.167 10 false C 5.583,7.865 5.729,8.031 0.146,0.167 10 false C 4.677,8.115 4.823,8.281 0.146,0.167 10 false B 5.323,8.469 5.469,8.635 0.146,0.167 10 false B 0.969,6.313 1.115,6.479 0.146,0.167 10 false D 4.292,6.344 4.438,6.51 0.146,0.167 10 false E 0.729,4.885 1.24,5.188 0.51,0.302 10 false A - A 2.688,4.875 3.146,5.104 0.458,0.229 10 false B - B 4.667,4.875 5.281,5.208 0.615,0.333 10 false C - C 3.635,4.906 4.25,5.167 0.615,0.26 10 false *c 1.625,4.979 2.25,5.188 0.625,0.208 10 false *a 1.979,5.333 3.01,5.625 1.031,0.292 10 false *b 5.615,4.938 6.417,5.229 0.802,0.292 10 false *e 5.833,5.271 7.01,5.771 1.177,0.5 10 false *f 3.969,5.354 4.969,5.781 1,0.427 10 false *d
*a 2.5 mm (0.10 in.) *b 2.5 to 3.5 mm (0.10 to 0.14 in.)
*c 5.0 mm (0.20 in.) *d 4.5 to 5.5 mm (0.18 to 0.22 in.)
*e 7.5 mm (0.30 in.) *f 7.0 to 8.0 mm (0.28 to 0.31 in.)


Seal Packing:
Item Seal Packing
Dashed line Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Continuous line
Alternate long and short dashed line Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


Application Specification:
Area Seal Packing Diameter Distance from Edge of Cover to: Seal Packing Application Length Distance from Top of Cover to Top of Seal Packing
Dashed line 2.5 to 3.5 mm (0.0984 to 0.138 in.) Center of seal packing
2.5 mm (0.0984 in.)
- -
Continuous line 4.5 to 5.5 mm (0.177 to 0.217 in.) or 7.0 to 8.0 mm (0.276 to 0.315 in.) - - -
Alternate long and short dashed line 4.0 mm (0.157 in.) Center of seal packing
3.0 mm (0.118 in.)
- -
(A) - (A) 2.5 to 3.5 mm (0.0984 to 0.138 in.) Center of seal packing
2.5 mm (0.0984 in.)
- -
(B) - (B) 4.5 to 5.5 mm (0.177 to 0.217 in.) Opposite edge of seal packing
5.0 mm (0.197 in.)
- -
(C) - (C) 7.0 to 8.0 mm (0.276 to 0.315 in.) Opposite edge of seal packing
7.5 mm (0.295 in.)
- -
(F) 4.5 to 5.5 mm (0.177 to 0.217 in.) - 15.8 mm (0.622 in.) 50.1 mm (1.97 in.)
(G) 4.5 to 5.5 mm (0.177 to 0.217 in.) - 10.3 mm (0.406 in.) 155.1 mm (6.11 in.)
(H) 7.0 to 8.0 mm (0.276 to 0.315 in.) - 19.5 mm (0.768 in.) 165.4 mm (6.51 in.)
(I) 4.5 to 5.5 mm (0.177 to 0.217 in.) - 14.6 mm (0.575 in.) 397.8 mm (15.7 in.)
(J) 4.5 to 5.5 mm (0.177 to 0.217 in.) - 18.6 mm (0.732 in.) 51.4 mm (2.02 in.)
(K) 4.5 to 5.5 mm (0.177 to 0.217 in.) - 25.3 mm (0.996 in.) 133.9 mm (5.27 in.)
(L) 7.0 to 8.0 mm (0.276 to 0.315 in.) - 25.8 mm (1.02 in.) 159.2 mm (6.27 in.)
(M) 4.5 to 5.5 mm (0.177 to 0.217 in.) - 5.0 mm (0.197 in.) 185.0 mm (7.28 in.)
(N) 4.5 to 5.5 mm (0.177 to 0.217 in.) - 14.6 mm (0.575 in.) 397.8 mm (15.7 in.)
(O) 4.0 mm (0.157 in.) Center of seal packing
3.0 mm (0.118 in.)
- -


NOTICE:

Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.



i.

Clean the bolts and their installation holes.


j.
A057108C34
2.156,0.26 2.031,0.26 2.031,0.26 1.75,1.292 false 2.229,0.208 2.542,0.365 0.313,0.156 10 *1
*1 Adhesive


Apply adhesive to 5 and a half threads or more of the end of the bolt (C).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



k.
A320281C02
1.677,1.698 1.917,1.458 1.917,1.458 2.594,1.458 true 2.646,1.396 2.958,1.594 0.313,0.198 10 false *1 0.625,0.781 0.781,0.979 0.156,0.198 10 false A 0.729,1.604 0.885,1.802 0.156,0.198 10 false A 0.76,1.927 0.917,2.125 0.156,0.198 10 false A 0.74,2.26 0.896,2.458 0.156,0.198 10 false A 2.156,3.208 2.313,3.406 0.156,0.198 10 false A 2.333,2.729 2.49,2.927 0.156,0.198 10 false A 2.385,2.51 2.542,2.708 0.156,0.198 10 false A 2.417,2.198 2.573,2.396 0.156,0.198 10 true A 2.969,1.885 3.125,2.083 0.156,0.198 10 true A 2.344,1.896 2.5,2.094 0.156,0.198 10 true A 2.521,1.698 2.677,1.896 0.156,0.198 10 true A 0.729,1.219 0.885,1.417 0.156,0.198 10 false B 0.635,0.948 0.792,1.146 0.156,0.198 10 false B 2.448,1.042 2.604,1.24 0.156,0.198 10 false B 2.344,1.26 2.5,1.458 0.156,0.198 10 false B 2.229,1.51 2.385,1.708 0.156,0.198 10 true A 0.563,0.573 0.719,0.771 0.156,0.198 10 false C 2.594,0.573 2.75,0.771 0.156,0.198 10 false C 1.49,2.031 1.646,2.229 0.156,0.198 10 true D
*1 Seal Washer


Temporarily install the timing chain cover sub-assembly with the 19 bolts and a new seal washer.

Bolt Length:
Item Length Thread Diameter
Bolt (A), (C) 35 mm (1.38 in.) 8 mm (0.315 in.)
Bolt (B) 55 mm (2.17 in.) 10 mm (0.394 in.)
Bolt (D) 40 mm (1.57 in.) 6 mm (0.236 in.)


NOTICE:

Make sure that there is no oil on the threads of the bolts.



l.

Temporarily install the engine mounting bracket RH with the 3 bolts.

Bolt Length:
Length Thread Diameter
80 mm (3.15 in.) 10 mm (0.394 in.)


NOTICE:

Make sure that there is no oil on the threads of the bolts.



m.

Install 2 new O-rings to the timing chain cover sub-assembly.


n.

Temporarily install the oil filter bracket with the 4 bolts.

Bolt Length:
Length Thread Diameter
35 mm (1.38 in.) 8 mm (0.315 in.)


NOTICE:

Make sure that there is no oil on the threads of the bolts.



o.

Fully tighten the 26 bolts in the order shown in the illustration.

A313811C03
0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 3.771,0.083 4.083,0.24 0.313,0.156 10 false *b 0.625,2.531 0.781,2.698 0.156,0.167 10 false A 0.531,0.875 0.688,1.073 0.156,0.198 10 false B 0.417,0.458 0.604,0.646 0.188,0.188 10 false C 1.604,2.073 1.76,2.271 0.156,0.198 10 true D 1.688,1.177 1.854,1.344 0.167,0.167 10 false E 0.5,0.688 0.656,0.854 0.156,0.167 10 false A 0.635,1.26 0.792,1.458 0.156,0.198 10 false B 0.635,2.354 0.792,2.521 0.156,0.167 10 false A 0.635,1.979 0.792,2.146 0.156,0.167 10 false A 0.635,1.604 0.792,1.771 0.156,0.167 10 false A 0.781,2.771 0.938,2.969 0.156,0.198 10 true A 1.031,2.938 1.188,3.104 0.156,0.167 10 true A 0.802,3.104 0.958,3.271 0.156,0.167 10 true A 1.771,3.594 1.969,3.771 0.198,0.177 10 false A 2.385,2.875 2.552,3.042 0.167,0.167 10 false A 2.438,2.354 2.594,2.542 0.156,0.188 10 true A 2.344,2 2.521,2.188 0.177,0.188 10 true A 3.083,1.927 3.313,2.177 0.229,0.25 10 false A 2.448,2.531 2.573,2.667 0.125,0.135 10 false A 2.313,1.594 2.448,1.76 0.135,0.167 10 true A 2.573,1.75 2.729,1.906 0.156,0.156 10 true A 1.604,1.344 1.729,1.531 0.125,0.188 10 true E 2.385,1.229 2.542,1.427 0.156,0.198 10 false B 2.5,1 2.656,1.198 0.156,0.198 10 true B 2.698,0.458 2.896,0.635 0.198,0.177 10 true C 2.573,0.719 2.74,0.885 0.167,0.167 10 false E 4.125,0.448 4.375,0.615 0.25,0.167 10 false 17 4.198,0.688 4.448,0.854 0.25,0.167 10 false 16 4.292,0.875 4.542,1.042 0.25,0.167 10 false 4 4.365,1.24 4.615,1.406 0.25,0.167 10 false 2 4.333,1.594 4.583,1.76 0.25,0.167 10 false 15 4.302,1.99 4.552,2.156 0.25,0.167 10 false 14 4.271,2.344 4.521,2.51 0.25,0.167 10 false 13 4.281,2.542 4.531,2.708 0.25,0.167 10 false 22 4.438,2.76 4.667,2.938 0.229,0.177 10 true 24 4.698,2.938 4.927,3.104 0.229,0.167 10 true 25 4.448,3.104 4.667,3.271 0.219,0.167 10 true 23 5.479,3.583 5.729,3.75 0.25,0.167 10 false 12 6.104,2.875 6.354,3.042 0.25,0.167 10 false 11 6.167,2.531 6.417,2.698 0.25,0.167 10 false 10 6.177,2.344 6.427,2.51 0.25,0.167 10 true 9 6.094,2 6.344,2.167 0.25,0.167 10 true 8 6.792,1.927 7.042,2.094 0.25,0.167 10 false 26 6.313,1.729 6.563,1.896 0.25,0.167 10 true 7 6.042,1.583 6.24,1.74 0.198,0.156 10 true 6 5.313,2.052 5.563,2.219 0.25,0.167 10 true 18 5.396,1.188 5.646,1.354 0.25,0.167 10 true 20 5.25,1.344 5.469,1.51 0.219,0.167 10 true 21 6.125,1.229 6.375,1.396 0.25,0.167 10 false 1 6.229,1 6.479,1.167 0.25,0.167 10 true 3 6.302,0.729 6.552,0.896 0.25,0.167 10 true 19 6.427,0.469 6.677,0.635 0.25,0.167 10 false 5
*a Torque *b Bolt Tightening Order


Torque:
Bolt (A), (C) : 25.5 N*m (260 kgf*cm, 19 ft.*lbf)
Bolt (B), (E) : 51 N*m (520 kgf*cm, 38 ft.*lbf)
Bolt (D) : 10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

Tighten the bolts within 10 minutes of applying seal packing.

·

Do not add engine oil for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.




Hide 13540 13.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 11213 14.INSTALL CYLINDER HEAD COVER GASKET

Hide 11201 15.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 16620 16.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 12551A 17.INSTALL NO. 1 VACUUM PUMP BRACKET

Hide 29300 18.INSTALL VACUUM PUMP ASSEMBLY

Hide 16267 24.CONNECT NO. 3 WATER BY-PASS HOSE

Hide 17167 27.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 11452 28.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 23250 29.INSTALL FUEL INJECTOR ASSEMBLY

Hide 23291 30.INSTALL INJECTOR VIBRATION INSULATOR

Hide 23807V 31.INSTALL NO. 1 DELIVERY PIPE SPACER

Hide 23807 32.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23901 33.CONNECT FUEL TUBE SUB-ASSEMBLY

Hide 34.INSTALL WIRE HARNESS CLAMP BRACKET

Hide 22271 38.INSTALL THROTTLE BODY GASKET

Hide 22210 39.INSTALL THROTTLE BODY ASSEMBLY