Home › Engine / Hybrid System › 3ZR-FAE (ENGINE MECHANICAL) › CYLINDER HEAD GASKET
RM32H0E _51 Engine / Hybrid System _059726 3ZR-FAE ENGINE MECHANICAL _0292814 CYLINDER HEAD GASKET A

3ZR-FAE ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 11115 1.INSTALL CYLINDER HEAD GASKET

a.
A215254C14
0.208,0.896 0.208,0.688 0.208,0.688 0.531,0.458 false 0.906,0.49 1.469,0.49 false 0.854,0.698 1.031,0.865 0.177,0.167 10 false *1 1.073,0.063 3.167,0.375 2.094,0.313 10 false 2 to 4 mm (0.0787 to 0.157 in.) 0.021,0.896 0.896,1.083 0.875,0.188 10 false 4.0 mm 0.302,1.146 1.5,1.49 1.198,0.344 10 false 10 to 15 mm (0.394 to 0.591 in.) 0.281,2.458 1.479,2.802 1.198,0.344 10 false 10 to 15 mm (0.394 to 0.591 in.) 1.51,0.396 1.823,0.594 0.313,0.198 10 false *a
*1 Cylinder Block Sub-assembly
*a Seal Packing
V100135

Engine Front


Apply seal packing (diameter 4.0 mm (0.157 in.)) to the cylinder block sub-assembly as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:

Remove any oil from the cylinder block sub-assembly.



b.
A221760C05
1.97,0.157 2.121,0.309 0.151,0.151 10 *a 1.464,0.494 1.649,0.248 1.649,0.248 1.954,0.248 false
*a Lot No.
V100135

Engine Front


Place a new cylinder head gasket on the cylinder block sub-assembly with the Lot No. stamp facing upward.

NOTICE:

Install the cylinder head gasket within 3 minutes of applying seal packing.



c.
A233569C08
0.438,0.833 0.438,0.74 0.438,0.74 0.729,0.458 false 2.135,0.427 1.938,0.427 1.938,0.427 1.365,0.625 false 1.646,2.573 1.448,2.375 1.448,2.375 1.302,2.375 false 1.656,1.063 0.917,1.177 0.917,1.177 0.906,1.302 false 1.49,0.313 1.292,0.313 1.292,0.313 1.104,0.5 false 2.177,0.365 2.448,0.531 0.271,0.167 10 false *1 1.25,0.083 3.083,0.385 1.833,0.302 10 false 0 to 2 mm (0 to 0.0787 in.) 0.281,0.865 0.938,1.125 0.656,0.26 10 false 4.0 mm 0.302,1.333 1.5,1.677 1.198,0.344 10 false 10 to 15 mm (0.394 to 0.591 in.) 0.083,2.281 1.281,2.625 1.198,0.344 10 false 10 to 15 mm (0.394 to 0.591 in.) 1.542,0.229 1.813,0.396 0.271,0.167 10 false *a
*1 Cylinder Head Gasket
*a Seal Packing
V100135

Engine Front


Apply seal packing (diameter 4.0 mm (0.157 in.)) to the new cylinder head gasket as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the cylinder head gasket and cylinder head sub-assembly.

·

Install the cylinder head gasket within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.




Hide 11101 2.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:

The cylinder head set bolts are tightened in 3 progressive steps.


a.

Place the cylinder head sub-assembly on the cylinder block sub-assembly.

NOTICE:
·

Make sure that no oil is on the mounting surface of the cylinder head sub-assembly.

·

Place the cylinder head sub-assembly on the cylinder block sub-assembly gently in order not to damage the cylinder head gasket with the bottom part of the cylinder head sub-assembly.




b.

Install the 10 plate washers to the 10 cylinder head set bolts.


c.

Apply a light coat of engine oil to the threads and under the heads of the 10 cylinder head set bolts.


d.
A150891N17
0.583,0.099 0.691,0.25 0.108,0.152 10 8 1.122,0.099 1.229,0.25 0.108,0.152 10 4 1.668,0.113 1.775,0.264 0.108,0.152 10 2 2.2,0.113 2.308,0.264 0.108,0.152 10 5 2.768,0.092 2.875,0.244 0.108,0.152 10 9 1.647,1.78 1.761,1.935 0.114,0.155 10 1 1.095,1.782 1.202,1.933 0.108,0.152 10 6 0.506,1.782 0.697,1.933 0.191,0.152 10 10 2.225,1.782 2.333,1.933 0.108,0.152 10 3 2.775,1.782 2.883,1.933 0.108,0.152 10 7

Step 1:

i.

Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head set bolts in several steps, in the order shown in the illustration.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:

Do not drop the plate washers into the cylinder head sub-assembly.




e.
A296910C01
1.635,1.688 1.948,1.094 false 1.521,1.75 1.833,1.948 0.313,0.198 10 *a 1.469,0.333 1.781,0.531 0.313,0.198 10 90° 2.583,0.094 3.042,0.292 0.458,0.198 10 45°
*a Paint Mark
V100135

Engine Front


Step 2:

i.

Mark each cylinder head set bolt head with paint as shown in the illustration.


ii.

Tighten the cylinder head set bolts 90° in the order shown in step 1.



f.

Step 3:

i.

Tighten the cylinder head set bolts another 45° in the order shown in step 1.



g.

Check that the paint marks are now at a 135° angle to the front.


h.
A393403C01
0.833,1.781 1.146,1.938 0.313,0.156 10 false *a 2.198,1.76 2.51,1.917 0.313,0.156 10 false *b
*a Before Wiping Off
*b After Wiping Off


After tightening the cylinder head set bolts, wipe off any seal packing material that seeped out from the contact surfaces between the cylinder head sub-assembly and cylinder block sub-assembly.

HINT:

Perform "Inspection After Repair" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 16268 4.INSTALL NO. 1 WATER BY-PASS PIPE

a.

Install the No. 1 water by-pass pipe with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 11103 5.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY