Home › Drivetrain › K114 (MULTIDRIVE / CVT) › OIL PAN › 2016.10–2019.09
RM32H0E _52 Drivetrain _059616 K114 MULTIDRIVE / CVT _0292837 OIL PAN A

K114 MULTIDRIVE / CVT  OIL PAN  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the transaxle oil (CVT) pan sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51444A 2.REMOVE REAR ENGINE UNDER COVER LH

Hide 35106L 3.REMOVE TRANSAXLE OIL (CVT) PAN SUB-ASSEMBLY

a.
C362022

Remove the refill plug and gasket from the continuously variable transaxle assembly.


b.
C365125

Using a 10 mm hexagon socket wrench, remove the drain plug and gasket from the transaxle oil (CVT) pan sub-assembly, and drain the fluid.


c.
C362023

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle oil (CVT) pan sub-assembly.


d.
C365127C02
2.76,0.531 2.917,0.635 false 2.594,0.427 2.906,0.625 0.313,0.198 10 false *1
*1 No. 1 Transmission Oil Filler Tube


Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle oil (CVT) pan sub-assembly.

HINT:

Removing the No. 1 transmission oil filler tube will drain all oil in the transaxle oil (CVT) pan sub-assembly.



e.
C295677

Remove the 19 bolts, transaxle oil (CVT) pan sub-assembly and transaxle oil pan (CVT) gasket from the continuously variable transaxle assembly.

NOTICE:

Some fluid will remain in the transaxle oil (CVT) pan sub-assembly. Remove all the bolts, and carefully remove the transaxle oil (CVT) pan sub-assembly.



f.

Temporarily install the gasket and refill plug to the continuously variable transaxle assembly.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.



Hide 35394D 4.REMOVE OIL CLEANER (CVT) MAGNET

a.
C295678C02
1.448,0.885 2.26,0.885 false 1.76,1.51 1.76,0.885 false 1.271,0.823 1.583,1.021 0.313,0.198 10 true *1
*1 Oil Cleaner (CVT) Magnet


Remove the 2 oil cleaner (CVT) magnets from the transaxle oil (CVT) pan sub-assembly.


b.

Clean off any metal particles adhered to the 2 oil cleaner (CVT) magnets.


c.

Clean the transaxle oil (CVT) pan sub-assembly and remove any metal particles, sludge, etc.


Hide 35330D 5.REMOVE OIL STRAINER ASSEMBLY

HINT:

Perform this procedure only when replacement of the oil strainer assembly is necessary.


a.
C409870

Remove the 2 bolts and oil strainer assembly from the transmission valve body assembly.


b.
C409871

Remove the O-ring from the oil strainer assembly.