Home › Engine / Hybrid System › 3ZR-FAE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059726 3ZR-FAE ENGINE MECHANICAL _0292817 ENGINE ASSEMBLY A

3ZR-FAE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Simple intelligent parking assist system*1 (Click here)
Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)*1
Initialize back door lock Power door lock control system (Click here)
·

Replacement of engine assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF thermal Degradation Estimate" is not estimated correctly (Click here)
Front wheel alignment adjustment Perform the following procedures in the order shown:
1.

Clear zero point calibration data and store system information

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information


·

VSC disabled or malfunctions

·

DTCs are stored

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ Simple Intelligent Parking Assist System)>CALIBRATION

CAUTION:
·
A340377C22
0.542,1.115 0.958,1.115 false 0.344,1.01 0.656,1.208 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the engine lifter


Because the weight of the engine with transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the engine lifter could drop and components could fall down.


·
A340359C12
0.375,1.135 0.75,1.281 true 0.135,1.031 0.448,1.229 0.313,0.198 10 false *a
*a High temperature areas


Do not touch the engine or exhaust manifold converter sub-assembly when they are hot.

·

Touching the engine or exhaust manifold converter sub-assembly when they are hot could result in burns.


·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 28800 5.REMOVE BATTERY

Hide 6.REMOVE FRONT WHEELS

Hide 51441 7.REMOVE NO. 1 ENGINE UNDER COVER

a.
A390450

Remove the 4 bolts, 4 screws, 4 clips and No. 1 engine under cover from the vehicle.


Hide 51444A 8.REMOVE REAR ENGINE UNDER COVER LH

a.
A393400

Remove the 6 clips and rear engine under cover LH from the vehicle.


Hide 51443C 9.REMOVE REAR ENGINE UNDER COVER RH

a.
A393399

Remove the 6 clips and rear engine under cover RH from the vehicle.


Hide 11.DRAIN ENGINE COOLANT

Hide 12.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 15.DISCONNECT WIRE HARNESS

a.
A394172

Remove the 2 bolts to separate the engine wire from the vehicle.


b.
A393409

Remove the bolt and nut to separate the engine wire from the battery clamp sub-assembly.


c.
A393410

Remove the 3 nuts to separate the engine wire from the positive (+) battery terminal.


d.
A393411

Remove the bolt to separate the engine wire from the transaxle assembly.


Hide 74404A 16.REMOVE BATTERY CLAMP SUB-ASSEMBLY

a.
A393412

Disengage the clamp to separate the engine wire from the battery clamp sub-assembly.


b.

Remove the 3 bolts and battery clamp sub-assembly from the vehicle.


Hide 16571C 17.DISCONNECT NO. 1 RADIATOR HOSE

A393413

a.

Slide the clip and disconnect the No. 1 radiator hose from the cylinder head sub-assembly.


Hide 16572D 18.DISCONNECT NO. 2 RADIATOR HOSE

A393414

a.

Slide the clip and disconnect the No. 2 radiator hose from the water inlet.


Hide 23829A 20.DISCONNECT FUEL VAPOR FEED HOSE

a.
A393415

Slide the clip and disconnect the fuel vapor feed hose from the purge valve (purge VSV).


Hide 44750 21.DISCONNECT UNION TO CONNECTOR TUBE HOSE

A393416

a.

Slide the clip and disconnect the union to connector tube hose from the vacuum pump assembly.


Hide 87246 22.DISCONNECT OUTLET HEATER WATER HOSE

a.
A393417

Disengage the clamp.


b.

Slide the clip and disconnect the outlet heater water hose from the No. 3 water by-pass hose.


Hide 87245 23.DISCONNECT INLET HEATER WATER HOSE

a.
A393418

Slide the clip and disconnect the inlet heater water hose from the No. 1 water by-pass pipe.


Hide 23901 24.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A393419

Disengage the claw and remove the No. 1 fuel pipe clamp.


b.
A167796

Pinch the retainer as shown in the illustration, then pull the fuel tube connector off the fuel pipe.

NOTICE:
·

Remove any dirt and foreign matter from the fuel tube connector before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them, as the fuel tube connector has O-rings that seal the fuel pipe.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, kink or twist the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag after disconnecting the fuel tube sub-assembly.

·

If the fuel tube connector and fuel pipe are stuck, push and pull to release them.




Hide 88703 25.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 88704 26.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 27. SECURE STEERING WHEEL ASSEMBLY

Hide 45259A 28.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 29.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45025D 30.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 57533B 31.REMOVE FRONT FLOOR CENTER BRACE

Hide 17410 32.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Front and Rear Catalyst)

Hide 32101G 35.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

Hide 51108A 36.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 37.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 38.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle and front suspension crossmember sub-assembly level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.




b.
A393420

Remove the 2 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.


c.
A393421

Remove the bolt and nut and separate the engine mounting insulator LH from the engine mounting bracket LH.

NOTICE:

While holding the nut in place, loosen the bolt.



d.
A392289

Remove the 6 bolts to separate the front suspension crossmember sub-assembly from the vehicle.


e.

Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.




Hide 39.REMOVE WIRE HARNESS CLAMP BRACKET

A393422

a.

Disengage the 5 clamps.


b.

Disconnect the air fuel ratio sensor connector.


c.

Remove the bolt and wire harness clamp bracket.


Hide 40.INSTALL ENGINE HANGER

a.
A317993C04
0.969,1.031 1.438,1.031 true 2.385,1.021 2.854,1.021 true 1.458,0.948 1.771,1.146 0.313,0.198 10 true *1 2.115,0.927 2.396,1.125 0.281,0.198 10 true *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger
V100135

Bolt


Install the No. 1 engine hanger and No. 2 engine hanger with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-37070
No. 2 Engine Hanger 12282-37060
Bolt 91552-81050



b.

Attach an engine sling device and hang the engine assembly with transaxle with a chain block.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.

·

Do not perform any procedure while the engine assembly with transaxle is suspended because doing so may cause the engine assembly with transaxle to drop, resulting in injury. However, the engine assembly with transaxle needs to be suspended when it is installed to or removed from an engine stand.




Hide 12372A 41.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A393423

Remove the 4 bolts, nut and engine mounting insulator LH from the vehicle.


Hide 12305 42.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A393424

Remove the 2 bolts and No. 2 earth wire from the engine mounting insulator sub-assembly RH and vehicle.


b.
A393425

Remove the bolt, nut and disconnect the air conditioner tube and accessory assembly.


c.

Remove the 2 bolts, nut and engine mounting insulator sub-assembly RH from the vehicle.


Hide 28100 43.REMOVE STARTER ASSEMBLY

Hide 11363A 44.REMOVE FLYWHEEL HOUSING SIDE COVER

a.
A394158

Remove the flywheel housing side cover from the cylinder block sub-assembly.


Hide 82121 45.REMOVE ENGINE WIRE

a.

Disconnect all the clamps and connectors and remove the engine wire from the engine assembly with transaxle.


Hide 16267 46.REMOVE NO. 3 WATER BY-PASS HOSE

a.
A393426

Disengage the clamp.


b.

Slide the 2 clips and remove the No. 3 water by-pass hose from the cylinder head sub-assembly and oil cooler.


Hide 16281F 47.REMOVE NO. 5 WATER BY-PASS HOSE

a.
A318002

Disengage the 2 clamps.


b.

Slide the 2 clips and remove the No. 5 water by-pass hose from the No. 3 water by-pass pipe and oil cooler.


Hide 32101B 49.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 16361A 50.REMOVE FAN AND GENERATOR V BELT

Hide 27020 51.REMOVE GENERATOR ASSEMBLY

Hide 52.REMOVE COMPRESSOR WITH PULLEY ASSEMBLY

Hide 53.INSTALL ENGINE TO ENGINE STAND

a.

Install the engine assembly to an engine stand.


Hide 54.REMOVE ENGINE HANGER

a.

Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger.