Home › Engine / Hybrid System › 3ZR-FAE (ENGINE CONTROL) › IGNITION SYSTEM
RM32H0E _51 Engine / Hybrid System _059607 3ZR-FAE ENGINE CONTROL _0293868 IGNITION SYSTEM G

3ZR-FAE ENGINE CONTROL  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.PERFORM SPARK TEST

CAUTION:
·
A345137

When working near the engine room while the engine has started or the power source mode is ignition switch to ON (IG), do not touch the fan and generator V belt or rotating components such as the fan, etc.

·

Touching the fan and generator V belt or rotating components such as the fan, etc. could result in your hand or clothing getting caught and pulled in.

·
A344783

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust manifold.

·

Touching high-temperature areas such as the engine and exhaust manifold could result in burns.



HINT:

Perform "Inspection After Repair" after replacing a spark plug or ignition coil assembly.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Check for DTCs.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

NOTICE:

If any DTCs are present, perform troubleshooting in accordance with the procedure for each DTC.



b.

Remove the 4 ignition coil assemblies and 4 spark plugs.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>REMOVAL

NOTICE:
·

If a spark plug has been struck or dropped, replace it.

·

If an ignition coil assembly has been struck or dropped, replace it.



HINT:

Arrange the removed parts in the correct order.



c.
A391991

Disconnect the 4 fuel injector assembly connectors.

NOTICE:

Perform this step in order to stop fuel injection to prevent damage to the catalyst due to unburned fuel.



d.
A391992

Install the spark plug into the ignition coil assembly, and then connect the ignition coil assembly connector.


e.

Ground the spark plug.


f.

Check that spark occurs at each spark plug while the engine is being cranked.

NOTICE:
·

Be sure to ground the spark plugs when checking them.

·

Do not crank the engine for more than 2 seconds.

·

If a spark plug has been struck or dropped, replace it.

·

If an ignition coil assembly has been struck or dropped, replace it.




g.

If spark does not occur, perform the following procedure.


h.

Connect the 4 fuel injector assembly connectors.


i.

Install the 4 spark plugs and 4 ignition coil assemblies.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>INSTALLATION

NOTICE:
·

If a spark plug has been struck or dropped, replace it.

·

If an ignition coil assembly has been struck or dropped, replace it.



HINT:

Install the same parts to their original positions.





Hide 2.INSPECT IGNITION COIL ASSEMBLY AND SPARK TEST

CAUTION:
·
A345137

When working near the engine room while the engine has started or the power source mode is ignition switch to ON (IG), do not touch the fan and generator V belt or rotating components such as the fan, etc.

·

Touching the fan and generator V belt or rotating components such as the fan, etc. could result in your hand or clothing getting caught and pulled in.

·
A344783

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust manifold.

·

Touching high-temperature areas such as the engine and exhaust manifold could result in burns.



HINT:

Perform "Inspection After Repair" after replacing a spark plug or ignition coil assembly.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Check that the ignition coil assembly connector is securely connected.

Result:
Result Action
NG Connect securely
OK Go to next step



b.

Perform a spark test on each ignition coil assembly.

i.

Replace the ignition coil assembly with a known good one.


ii.

Perform the spark test again.

Result:
Result Action
NG Go to next step
OK Replace ignition coil assembly




c.

Perform a spark test on each spark plug.

i.

Replace the spark plug with a known good one.


ii.

Perform the spark test again.

Result:
Result Action
NG Inspect ignition system
Click here(Click here)
OK Replace spark plug


NOTICE:
·

If an ignition coil assembly has been struck or dropped, replace it.

·

If a spark plug has been struck or dropped, replace it.





d.

Connect the 4 fuel injector assembly connectors.


e.

Install the 4 spark plugs and 4 ignition coil assemblies.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>INSTALLATION

NOTICE:
·

If an ignition coil assembly has been struck or dropped, replace it.

·

If a spark plug has been struck or dropped, replace it.



HINT:

Install the same parts to their original positions.





Hide 19100P 3.INSPECT SPARK PLUG

CAUTION:
·
A345137

When working near the engine room while the engine has started or the power source mode is ignition switch to ON (IG), do not touch the fan and generator V belt or rotating components such as the fan, etc.

·

Touching the fan and generator V belt or rotating components such as the fan, etc. could result in your hand or clothing getting caught and pulled in.

·
A344783

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust manifold.

·

Touching high-temperature areas such as the engine and exhaust manifold could result in burns.



NOTICE:
·

Do not damage the iridium tip and platinum tip.

·

Check the iridium tip visually since the iridium tip may be damaged.

·

Never attempt to adjust the electrode gap of a used spark plug.

·

Replace with new spark plugs if extremely dirty due to sludge, etc.

·

Replace with new spark plugs if damaged at all.

·

Replace with a new spark plug if it has been struck or dropped.

·

When replacing with a new spark plug, do not remove the cap for protecting the spark plug tip until it is installed to the engine.

·

Do not use a wire brush for cleaning.



HINT:

Perform "Inspection After Repair" after replacing a spark plug.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A321045C01
0.885,1.979 1.083,1.896 false 0.708,1.885 1.021,2.042 0.313,0.156 10 false *a
*a Body Ground


Check the electrode.

i.

Using a megohmmeter, measure the insulation resistance.

Standard Insulation Resistance:
Tester Connection Condition Specified Condition
Spark plug (terminal part) - Body ground Always 10 MΩ or higher


HINT:

If a megohmmeter is not available, perform the following simple inspection instead.




b.

Alternative inspection method.

i.

Start the engine.

NOTICE:

Do not perform this step when any of the following DTCs are output: P0300, P0301, P0302, P0303, P0304 (Cylinder Misfire Detected).



ii.

Quickly accelerate the engine to 4000 rpm 5 times.

NOTICE:

Do not perform this step when any of the following DTCs are output: P0300, P0301, P0302, P0303, P0304 (Cylinder Misfire Detected).



iii.

Remove the spark plug.

Click hereGeneral>MAINTENANCE>3ZR-FAE SPARK PLUG>REMOVAL


iv.

Visually check the spark plug.

HINT:

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.




c.

Check the spark plug for any damage to its threads and insulator.

If there is any damage, replace the spark plug.

Recommended Spark Plug:
Manufacturer Spark Plug Type
DENSO SC16HR11



d.
A126880C06
0.719,1.115 0.885,1.302 0.167,0.188 10 *a
*a Spark Plug Electrode Gap


Check the spark plug electrode gap.

Maximum Electrode Gap for Used Spark Plug:

1.3 mm (0.0512 in.)


NOTICE:

Never attempt to adjust the electrode gap of a used spark plug.


If the spark plug electrode gap is more than the maximum, replace the spark plug.

Electrode Gap for New Spark Plug:

1.0 to 1.1 mm (0.0394 to 0.0433 in.)



e.

Install the spark plug.

Click hereGeneral>MAINTENANCE>3ZR-FAE SPARK PLUG>INSTALLATION


Hide 4.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing a spark plug or ignition coil assembly.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION