Home › Engine / Hybrid System › 8NR-FTS (INTAKE / EXHAUST) › EXHAUST PIPE (for 2WD) › 2016.10–2018.05
RM32H0E _51 Engine / Hybrid System _059908 8NR-FTS INTAKE / EXHAUST _0293892 EXHAUST PIPE(for 2WD) A

8NR-FTS INTAKE / EXHAUST  EXHAUST PIPE(for 2WD)  INSTALLATION  


PROCEDURE

Hide 17410 2.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Standard Length 43.0 mm (1.69 in.)
Minimum Free Length 41.5 mm (1.63 in.)

If the free length is less than the minimum, replace the compression spring.


b.

Temporarily install a new exhaust pipe gasket to the exhaust manifold converter sub-assembly (TWC: Front Catalyst).


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
*2 Exhaust Pipe Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the exhaust pipe gasket until its surface is flush with the exhaust manifold converter sub-assembly (TWC: Front Catalyst).

NOTICE:
·

Be sure to install the exhaust pipe gasket in the correct direction.

·

Do not reuse the exhaust pipe gasket.

·

Do not damage the exhaust pipe gasket.

·

Do not push in the exhaust pipe gasket by using the exhaust pipes when connecting them.




d.

Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the 2 exhaust pipe supports.


e.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C18
2.406,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.156,0.594 false 0.771,1.198 0.927,1.198 0.927,1.198 1.094,0.896 false 0.406,1.417 0.615,1.573 0.208,0.156 10 *a 0.573,0.146 0.823,0.302 0.25,0.156 10 *1 0.573,1.125 0.813,1.313 0.24,0.188 10 *2 2.698,0.083 2.927,0.26 0.229,0.177 10 *3
*1 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst)
*2 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*3 Exhaust Pipe Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst) is consistent front-to-rear and left-to-right.



f.

Engage the clamp and connect the heated oxygen sensor connector.


Hide 57533B 3.INSTALL FRONT FLOOR CENTER BRACE

a.

Install the 3 front floor center braces to the vehicle body with the 12 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 17430 4.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Standard Length 40 mm (1.57 in.)
Minimum Free Length 38.5 mm (1.52 in.)

If the free length is less than the minimum, replace the compression spring.


b.

Temporarily install a new exhaust pipe gasket to the front exhaust pipe assembly (TWC: Rear Catalyst).


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Exhaust Pipe Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the exhaust pipe gasket until its surface is flush with the front exhaust pipe assembly (TWC: Rear Catalyst).

NOTICE:
·

Be sure to install the gasket in the correct direction.

·

Do not reuse the exhaust pipe gasket.

·

Do not damage the exhaust pipe gasket.

·

Do not push in the exhaust pipe gasket by using the exhaust pipes when connecting them.




d.

Connect the tail exhaust pipe assembly to the 4 exhaust pipe supports.


e.

Install the tail exhaust pipe assembly to the front exhaust pipe assembly (TWC: Rear Catalyst) with the 2 bolts and 2 compression springs.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C18
2.406,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.156,0.594 false 0.771,1.198 0.927,1.198 0.927,1.198 1.094,0.896 false 0.406,1.417 0.615,1.573 0.208,0.156 10 *a 0.573,0.146 0.823,0.302 0.25,0.156 10 *1 0.573,1.125 0.813,1.313 0.24,0.188 10 *2 2.698,0.083 2.927,0.26 0.229,0.177 10 *3
*1 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Tail Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space between Flanges: 6.5 mm (0.256 in.)


After installation, check that the space between the flanges of the tail exhaust pipe assembly and front exhaust pipe assembly (TWC: Rear Catalyst) is consistent front-to-rear and left-to-right.



Hide 5.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

a.

Perform Inspection After Repair after repairing an exhaust gas leak.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Hide 58166 6.INSTALL FRONT FLOOR COVER LH (w/ Cover)

a.

Engage the 5 clamps to install the front floor cover LH to the vehicle body with the 2 bolts and clip.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 58165B 7.INSTALL FRONT FLOOR COVER RH (w/ Cover)

HINT:

Perform the same procedure as for the front floor cover LH.