Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM32H0E _55 Steering _059604 STEERING COLUMN _0293907 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2788  IG2 Signal Malfunction  


DESCRIPTION

This DTC is stored when the steering lock ECU (steering lock actuator or upper bracket assembly) detects an IG2 power supply malfunction.

HINT:

The steering lock ECU (steering lock actuator or upper bracket assembly) is not connected to the CAN communication system. However, the steering lock ECU (steering lock actuator or upper bracket assembly) is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2788 IG2 Signal Malfunction Mismatch between the steering lock ECU (steering lock actuator or upper bracket assembly) IG2 input from the LIN communication system and from the direct line. (1-trip detection logic (Only output while a malfunction is present and the engine switch is on (IG).))
·

IGN NO. 2 fuse

·

Steering lock ECU (Steering lock actuator or upper bracket assembly)

·

Harness or connector


DTC Output Confirmation Operation: No confirmation operation is necessary (monitoring is continuous).

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the engine cannot be started. -

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2788 - -

WIRING DIAGRAM

C351386E03
5.385,2.188 5.844,2.385 0.458,0.198 10 false GND 5.396,1.396 5.854,1.594 0.458,0.198 10 false IG2 5.396,0.583 5.854,0.781 0.458,0.198 10 false LIN 5.177,0.417 5.635,0.615 0.458,0.198 10 false 5 5.177,1.271 5.635,1.469 0.458,0.198 10 false 6 5.177,2.052 5.635,2.25 0.458,0.198 10 false 1 1.302,0.406 1.76,0.604 0.458,0.198 10 false 13 0.969,0.594 1.427,0.792 0.458,0.198 10 false LIN 4.417,2.833 5.448,3.104 1.031,0.271 10 false F78 4.417,3 7.104,3.479 2.688,0.479 10 false Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly) 0.052,3.01 1.594,3.604 1.542,0.594 10 false Certification ECU (Smart Key ECU Assembly) 0.063,2.833 1.604,3.427 1.542,0.594 10 false F1 1.333,1.333 2.917,1.667 1.583,0.333 10 false from IG2-NO. 2 Relay 3.667,1.552 5.094,1.813 1.427,0.26 10 false ECU-IG2 NO. 3 0.865,4.333 2.75,4.573 1.885,0.24 10 false LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After performing repairs, confirm that no DTCs are output again.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR

·

When replacing the steering lock ECU (steering lock actuator or upper bracket assembly), registration must be performed (refer to Service Bulletin).



PROCEDURE

1.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) (POWER SOURCE MODE SIGNAL)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the F78 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


c.
C350526C08
1.531,0.781 2.031,1.031 0.5,0.25 0.75,1.938 1.281,2.427 true 0.323,0.208 0.635,0.365 0.313,0.156 10 false *a 1.656,0.802 1.969,0.958 0.313,0.156 10 false F78 0.375,1.844 0.688,2 0.313,0.156 10 false GND
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F78-1 (GND) - Body ground Always Below 1 Ω



d.

Reconnect the F78 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


e.
C350527C17
1.5,0.417 2,0.667 0.5,0.25 0.99,2.74 1.354,1.958 true 2.76,2.771 2.271,1.958 true 0.177,0.208 0.49,0.365 0.313,0.156 10 false *a 0.854,2.802 1.167,2.958 0.313,0.156 10 false IG2 2.646,2.833 3.052,3 0.406,0.167 10 false GND 1.635,0.427 1.948,0.583 0.313,0.156 10 false F78
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F78-6 (IG2) - F78-1 (GND) Engine switch on (IG) 11 to 14 V
F78-6 (IG2) - F78-1 (GND) Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR