Home › Engine / Hybrid System › 8NR-FTS (EMISSION CONTROL) › EMISSION CONTROL SYSTEM
RM32H0E _51 Engine / Hybrid System _060038 8NR-FTS EMISSION CONTROL _0294110 EMISSION CONTROL SYSTEM G

8NR-FTS EMISSION CONTROL  EMISSION CONTROL SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
·
A345137

When working near the engine room while the engine has started or the power source mode is ignition switch to ON (IG), do not touch the fan and generator V belt or rotating components such as the fan, etc.

·

Touching the fan and generator V belt or rotating components such as the fan, etc. could result in your hand or clothing getting caught and pulled in.



PROCEDURE

Hide 1. VISUALLY INSPECT HOSES, CONNECTIONS AND GASKETS

a.

Visually check that the hoses, connections and gaskets have no cracks, leaks or damage.

NOTICE:
·

Detachment or other problems with the engine oil level dipstick, oil filler cap sub-assembly, ventilation hose and other components may cause the engine to run improperly.

·

Disconnection, looseness or cracks in the parts of the air induction system between the throttle body with motor assembly and cylinder head sub-assembly will allow air leaks which may lead to an engine failure or engine malfunctions.



If any defects are found, replace parts as necessary.


Hide 2.INSPECT EVAPORATIVE EMISSION CONTROL SYSTEM

CAUTION:
·
A345137

When working near the engine room while the engine has started or the power source mode is ignition switch to ON (IG), do not touch the fan and generator V belt or rotating components such as the fan, etc.

·

Touching the fan and generator V belt or rotating components such as the fan, etc. could result in your hand or clothing getting caught and pulled in.



a.

Connect the GTS to the DLC3.


b.
A393602

Slide the clip and disconnect the No. 1 fuel vapor feed hose from the purge valve (purge VSV).


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Activate the EVAP Purge VSV.

Powertrain > Engine > Active Test
Tester Display
Activate the EVAP Purge VSV
50004 372 1

f.

Check that vacuum occurs at the purge valve (purge VSV) port.


g.

If vacuum does not occur, check the following items.

·

Purge valve (purge VSV)

·

Clogs in the fuel vapor feed hose connecting the intake manifold and purge valve (purge VSV)



h.

Exit Active Test mode, connect the No. 1 fuel vapor feed hose to the purge valve (purge VSV) and slide the clip to secure it.


i.

Enter the following menus: Powertrain / Engine / Data List / EVAP (Purge) VSV.

Powertrain > Engine > Data List
Tester Display
EVAP (Purge) VSV
50003 372 226

j.

Warm up the engine and drive the vehicle.


k.

Confirm that the purge valve (purge VSV) opens.

If the result is not as specified, replace the purge valve (purge VSV), wire harness or ECM.


Hide 12217 3.INSPECT VENTILATION EJECTOR

a.

Remove the ventilation ejector from the cylinder head cover sub-assembly.

Click hereEngine / Hybrid System>8NR-FTS (EMISSION CONTROL)>MONOLITHIC CONVERTER>REMOVAL


b.
A353294C03
1.344,0.781 1.594,0.344 1.594,0.344 1.781,0.344 true 1.813,1.156 2.01,1.396 2.01,1.396 2.198,1.396 true 1.542,3.156 1.729,3.156 1.729,3.156 1.875,2.667 true 1.354,3.083 1.698,3.323 0.344,0.24 10 false *a 1.865,0.281 2.156,0.542 0.292,0.26 10 false *b 2.292,1.323 2.521,1.531 0.229,0.208 10 false *c
*a Pin
*b Valve
*c Ventilation Ejector


Check the operation of the valve.

i.

Insert the pin into the ventilation ejector hole and check that the valve moves smoothly.

OK:

The valve moves smoothly.


HINT:

If the valve does not move smoothly, it may be stuck inside the ventilation ejector.




c.

Install the ventilation ejector to the cylinder head cover sub-assembly.

Click hereEngine / Hybrid System>8NR-FTS (EMISSION CONTROL)>MONOLITHIC CONVERTER>INSTALLATION