Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _060061 SUPPLEMENTAL RESTRAINT SYSTEMS _0294190 AIRBAG SYSTEM D

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  DIAGNOSIS SYSTEM  



FUNCTION OF SRS WARNING LIGHT


a.

Primary check

i.

Turn the ignition switch off. Wait for at least 2 seconds, then turn the ignition switch ON. The SRS warning light comes on for approximately 6 seconds and diagnosis of the airbag system is performed.

HINT:

If malfunctions are detected during the primary check, the SRS warning light remains on even after the primary check period of approximately 6 seconds.




b.

Constant check

i.

After the primary check, the airbag sensor assembly constantly monitors the airbag system for malfunctions.

HINT:
If malfunctions are detected during the constant check, the airbag sensor assembly will indicate the malfunction as follows:
·

The SRS warning light comes on.

·

The SRS warning light goes off, and then comes on. This indicates a source voltage drop. The SRS warning light goes off 10 seconds after the source voltage returns to normal.





c.

Review

i.

When the airbag system is normal:

The SRS warning light comes on only during the primary check period of approximately 6 seconds after the ignition switch is turned ON.


ii.

When the airbag system is malfunctioning:

·

The SRS warning light remains on even after the primary check period.

·

The SRS warning light goes off after the primary check, but comes on again during the constant check.

·

The SRS warning light does not come on when the ignition switch is turned from off to ON.


HINT:

The SRS warning light will remain illuminated if any airbag or pretensioner has been deployed.





SRS WARNING LIGHT CHECK


a.
C265591

Turn the ignition switch ON, and check that the SRS warning light comes on for approximately 6 seconds (primary check).


b.

Check that the SRS warning light goes off approximately 6 seconds after the ignition switch is turned ON (constant check).

HINT:

When any of the following symptoms occur, refer to Problem Symptoms Table.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PROBLEM SYMPTOMS TABLE

·

The SRS warning light comes on occasionally after the primary check period.

·

The SRS warning light comes on, but DTCs are not output.

·

The ignition switch is turned from off to ON, but the SRS warning light does not come on.





FUNCTION OF PASSENGER AIRBAG ON/OFF INDICATOR (w/ Airbag Cut Off Switch)


a.

Initial check

i.

Turn the ignition switch ON.


ii.

The passenger airbag ON/OFF indicator comes on for approximately 4 seconds, then goes off for approximately 2 seconds.


iii.

Approximately 6 seconds after the ignition switch is turned ON, the passenger airbag ON/OFF indicator will indicate ON/OFF according to the airbag cut off switch cylinder sub-assembly condition as listed below.

Indicator Operation
Airbag Cut Off Switch Cylinder Sub-assembly Condition Passenger Airbag ON/OFF Indicator SRS Warning Light
ON Indicator OFF Indicator
ON ON OFF OFF
OFF OFF ON OFF
Switch failure OFF ON ON

HINT:

If the passenger airbag ON/OFF indicator does not operate as specified in the table according to the airbag cut off switch cylinder sub-assembly status and the SRS warning light is not illuminated, no DTC will be output. Therefore, perform troubleshooting for Trouble in Passenger Airbag ON/OFF Indicator.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>Trouble in Passenger Airbag ON/OFF Indicator


C284690E23
0.333,0.427 1.635,1 1.302,0.573 10 false Ignition Switch 1.667,0.24 2.74,0.833 1.073,0.594 10 false ON 1.667,0.656 2.76,1.094 1.094,0.438 10 false OFF 1.667,1.344 2.917,1.75 1.25,0.406 10 false ON 1.667,1.708 2.74,2.167 1.073,0.458 10 false OFF 1.667,2.344 2.76,2.75 1.094,0.406 10 false ON 1.667,2.708 2.5,3.229 0.833,0.521 10 false OFF 0.333,1.323 1.469,2.333 1.135,1.01 10 false Passenger Airbag ON/OFF Indicator ("ON") 0.333,2.333 1.469,3.333 1.135,1 10 false Passenger Airbag ON/OFF Indicator ("OFF") 3.25,1 4.521,2.667 1.271,1.667 10 false 4 sec. 3.25,2 4.583,2.667 1.333,0.667 10 false 4 sec. 4.167,1 5.5,1.417 1.333,0.417 10 false 2 sec. 4.167,2 5.5,2.417 1.333,0.417 10 false 2 sec. 4.208,3.083 7.156,3.573 2.948,0.49 10 false ON/OFF condition depends on the airbag cut off switch cylinder sub-assembly status result.




FUNCTION OF PASSENGER AIRBAG ON/OFF INDICATOR (w/ Airbag Cut Off Switch)


a.

Initial check

i.

Turn the ignition switch ON.


ii.

The passenger airbag ON/OFF indicator comes on for approximately 4 seconds, then goes off for approximately 2 seconds.


iii.

Approximately 6 seconds after the ignition switch is turned ON, the passenger airbag ON/OFF indicator will indicate ON/OFF depending on the following conditions.

Indicator Operation
Front Passenger Seat Condition Passenger Airbag ON/OFF Indicator SRS Warning Light
ON Indicator OFF Indicator
Vacant OFF ON OFF
Adult*1 is seated ON OFF OFF
Child*2 is seated ON or OFF*2 OFF or ON*2 OFF
Child restraint system is installed OFF ON OFF
Occupant classification system failure OFF ON ON

*1: The system judges a person of average adult weight or more as an adult. If a smaller adult sits in the front passenger seat, the system may not recognize them as an adult depending on their physique and posture.

*2: The system may not recognize a child or a child in a child restraint system as a child depending on factors such as the positioning of the child restraint system or the child's physique or posture.


HINT:
·

The passenger airbag ON/OFF indicator illuminates based on the following timing chart in order to check the indicator light circuit.

·

When the occupant classification system is malfunctioning, both the SRS warning light and passenger airbag ON/OFF indicator ("OFF") come on. In this case, perform troubleshooting for the airbag system DTCs first.



C284690E24
0.333,0.427 1.635,1 1.302,0.573 10 false Ignition Switch 1.667,0.24 2.74,0.833 1.073,0.594 10 false ON 1.667,0.656 2.76,1.094 1.094,0.438 10 false OFF 1.667,1.344 2.917,1.75 1.25,0.406 10 false ON 1.667,1.708 2.74,2.167 1.073,0.458 10 false OFF 1.667,2.344 2.76,2.75 1.094,0.406 10 false ON 1.667,2.708 2.5,3.229 0.833,0.521 10 false OFF 0.333,1.323 1.469,2.333 1.135,1.01 10 false Passenger Airbag ON/OFF Indicator ("ON") 0.333,2.333 1.469,3.333 1.135,1 10 false Passenger Airbag ON/OFF Indicator ("OFF") 3.25,1 4.521,2.667 1.271,1.667 10 false 4 sec. 3.25,2 4.583,2.667 1.333,0.667 10 false 4 sec. 4.167,1 5.5,1.417 1.333,0.417 10 false 2 sec. 4.167,2 5.5,2.417 1.333,0.417 10 false 2 sec. 4.615,3.104 6.75,3.625 2.135,0.521 10 false ON/OFF condition depends on the front passenger detection result.




PASSENGER AIRBAG ON/OFF INDICATOR CHECK (w/ Airbag Cut Off Switch)


a.

Turn the ignition switch ON.


b.

Check that the passenger airbag ON/OFF indicator ("ON" and "OFF") comes on for approximately 4 seconds, then goes off for approximately 2 seconds.

HINT:

Refer to the indicator operation table in Function of Passenger Airbag ON/OFF Indicator for the passenger airbag ON/OFF indicator operation when the ignition switch is turned ON and approximately 6 seconds elapse.




FUNCTION OF SRS CONNECTORS


a.

The SRS connectors are located as shown in the illustration.

C360603E04
0.073,0.042 3.375,0.281 3.302,0.24 12 false Connectors of ECU: 3.917,2.5 5.635,2.771 1.719,0.271 10 false Front Airbag Sensor LH/RH 3.917,3.073 6.417,3.333 2.5,0.26 10 false No. 1 Side Airbag Sensor LH/RH 3.917,3.625 6.417,3.885 2.5,0.26 10 false No. 2 Side Airbag Sensor LH/RH 3.927,4.188 6.427,4.448 2.5,0.26 10 false Door Side Airbag Sensor LH/RH 3.917,4.75 6.917,5.083 3,0.333 10 false Floor Side Airbag Sensor LH/RH 3.865,6.531 6.865,6.865 3,0.333 10 false Lower No. 1 Instrument Panel Airbag Assembly 3.917,7.083 6.917,7.417 3,0.333 10 false Front Seat Airbag Assembly LH/RH 3.917,7.656 6.917,7.99 3,0.333 10 false Other SRS Parts* 0.24,8.177 6.813,8.583 6.573,0.406 10 false *: Lower No. 1 Instrument Panel Airbag Assembly, Curtain Shield Airbag Assembly LH/RH, Front Seat Outer Belt Assembly LH/RH and Rear Seat 3 Point Type Outer Belt Assembly LH/RH 0.635,6.771 1.719,7.167 1.083,0.396 10 false to Airbag Sensor Assembly 2.75,5.958 4.281,6.302 1.531,0.344 10 false Spiral Cable with Sensor Sub-assembly 5.281,5.958 6.875,6.24 1.594,0.281 10 false Horn Button Assembly 0.115,5.333 3.417,5.573 3.302,0.24 12 false Connectors of Squib Circuit: 0.115,2.135 3.417,2.375 3.302,0.24 12 false Connectors of Sensor Circuit: 0.917,1.813 2.583,2.083 1.667,0.271 10 false to SRS Parts and Sensors 2.531,2.573 2.781,2.844 0.25,0.271 10 false 1 2.781,2.573 3.031,2.844 0.25,0.271 10 false 2 3.438,2.573 3.688,2.844 0.25,0.271 10 false 3 3.677,2.573 3.927,2.844 0.25,0.271 10 false 4 3.677,3.135 3.927,3.406 0.25,0.271 10 false 6 3.427,3.135 3.677,3.406 0.25,0.271 10 false 5 3.438,3.698 3.688,3.969 0.25,0.271 10 false 7 3.688,3.698 3.938,3.969 0.25,0.271 10 false 8 3.635,4.25 3.885,4.521 0.25,0.271 10 false 12 3.396,4.24 3.646,4.51 0.25,0.271 10 false 11 2.74,4.25 2.99,4.521 0.25,0.271 10 false 10 2.542,4.25 2.792,4.521 0.25,0.271 10 false 9 3.385,4.813 3.635,5.083 0.25,0.271 10 false 13 3.625,4.813 3.875,5.083 0.25,0.271 10 false 14 4.813,6.042 5.063,6.313 0.25,0.271 10 false 3 5.052,6.042 5.302,6.313 0.25,0.271 10 false 4 2.292,6.031 2.542,6.302 0.25,0.271 10 false 1 2.531,6.031 2.781,6.302 0.25,0.271 10 false 2 2.542,6.594 2.792,6.865 0.25,0.271 10 false 5 2.781,6.594 3.031,6.865 0.25,0.271 10 false 6 3.438,6.594 3.688,6.865 0.25,0.271 10 false 7 3.677,6.594 3.927,6.865 0.25,0.271 10 false 8 3.427,7.156 3.677,7.427 0.25,0.271 10 false 9 3.635,7.156 3.885,7.427 0.25,0.271 10 false 10 3.396,7.719 3.646,7.99 0.25,0.271 10 false 13 3.635,7.719 3.885,7.99 0.25,0.271 10 false 14 0.635,3.344 1.698,3.76 1.063,0.417 10 false to Airbag Sensor Assembly 0.948,0.458 2.615,0.729 1.667,0.271 10 false Airbag Sensor Assembly 0.75,0.875 0.99,1.094 0.24,0.219 10 false 1 1.677,0.875 1.927,1.146 0.25,0.271 10 false 2 2.573,0.865 2.823,1.135 0.25,0.271 10 false 3 0.75,1.313 1,1.583 0.25,0.271 10 false 4 1.677,1.313 1.927,1.583 0.25,0.271 10 false 5 2.573,1.313 2.823,1.583 0.25,0.271 10 false 6 1.677,1.083 1.927,1.354 0.25,0.271 10 false A

Connector Type Application
ECU Sensor Circuit Squib Circuit
Terminal Twin-lock Mechanism Connectors 4, 5, 6 Connectors 1, 9, 10 Connectors 1, 5, 6
Half Connection Prevention Mechanism - - Connectors 1, 5, 11
Activation Prevention Mechanism Connectors 4, 5, 6 - Connectors 2, 4, 6, 8, 10, 12, 14
Connector Lock Mechanism (1) - - Connectors 3, 7, 13
Connector Position Assurance Mechanism - Connectors 2, 3, 5, 7, 11, 13 Connectors 9
Connector Lock Mechanism (2) Connector A - -
Improper Connection Prevention Lock Mechanism Connector A - -


b.

Terminal twin-lock mechanism

C190972E05
2.438,0.094 2.052,0.094 false 2.813,0.656 2.438,0.094 false 5.708,0.094 5.573,0.094 false 5.854,0.635 5.708,0.094 false 0.729,0.01 2.083,0.188 1.354,0.177 10 Lance (Primary Lock) 1.229,1.448 2.167,1.625 0.938,0.177 10 Primary Lock 4.021,0.01 5.698,0.188 1.677,0.177 10 Spacer (Secondary Lock) 4.896,1.427 5.948,1.604 1.052,0.177 10 Secondary Lock

i.

This mechanism is designed to increase the ability of the terminal to remain connected and prevent it from accidentally being disconnected.


ii.

The connector has a two-piece construction consisting of the housing and spacer to securely lock the terminal using both the lance (primary lock) and spacer (secondary lock).



c.

Half connection prevention mechanism

C147461E79
1.531,1.417 1.417,1.083 1.417,1.083 1.25,1.083 false 1.833,1.375 1.75,0.833 1.75,0.833 1.583,0.833 false 2.354,1.333 2.167,0.5 2.167,0.5 2,0.5 true 3.01,1.208 3.25,0.583 3.25,0.583 3.417,0.583 true 3.198,1.313 3.417,0.917 3.417,0.917 3.583,0.917 true 6.063,1.156 5.917,0.75 5.917,0.75 5.75,0.75 true 1.167,0.396 2,0.604 0.833,0.208 10 false Locking Arm 1.01,0.719 1.563,0.917 0.552,0.198 10 false Stopper 0.417,1 1.271,1.25 0.854,0.25 10 false Locking Part 3.479,0.5 3.917,0.688 0.438,0.188 10 false Slider 3.656,0.823 4.125,1.01 0.469,0.188 10 false Spring 5.177,0.646 5.76,0.833 0.583,0.188 10 false Stopper 4.615,1.969 6.01,2.344 1.396,0.375 10 false Rebounded by Slider

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

If the connector is not completely connected, the connector is disconnected due to the spring force so that no continuity exists.



d.

Activation prevention mechanism

C238382E20
1.583,1.063 1.198,0.917 false 5.26,1.521 5.26,2.042 true 1.844,1.667 1.844,2.083 true 1.656,1.448 1.198,1.448 true 2.646,1.646 2.969,1.646 true 2.354,1.385 3,0.969 3,0.969 2.552,1.458 true 1.771,0.375 2.51,0.708 0.74,0.333 10 false When open 0.313,0.833 1.208,1.146 0.896,0.313 10 false Male Housing 3.042,0.885 4.115,1.229 1.073,0.344 10 false Female Terminal 0.302,1.375 1.198,1.698 0.896,0.323 10 false Male Terminal 3.01,1.573 4.073,1.938 1.063,0.365 10 false Female Housing 1.26,2.104 2.448,2.448 1.188,0.344 10 false Short Spring Plate 5.448,0.375 6.354,0.75 0.906,0.375 10 false When shorted 4.375,2.063 6.156,2.635 1.781,0.573 10 false Short spring plate contacting the male terminal

i.

This mechanism is designed to create a short circuit automatically between the positive and negative terminals of an airbag power source connector when disconnected.


ii.

The short spring plate contained in the connector creates a closed circuit on the airbag side (no potential difference can occur between both terminals), preventing accidental airbag deployment when servicing.



e.

Connector lock mechanism (1)

C147462E72
2.521,0.344 2.021,0.198 false 2.635,0.76 2.281,0.885 true 2.469,1.24 2.271,1.323 false 4.927,0.896 5.24,0.688 false 0.531,0.115 2.01,0.292 1.479,0.177 10 false Lock the locking button 1.927,0.813 2.302,0.979 0.375,0.167 10 false Claw 1.792,1.25 2.281,1.417 0.49,0.167 10 false Groove 5.281,0.604 6.927,1.031 1.646,0.427 10 false Claw on the locking button is locked in the groove

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Locking the connector locking button engages the locking button claws in the grooves on the other side of the connector to connect the connector securely.



f.

Connector Position Assurance (CPA) mechanism

C161464E55
0.833,1.104 0.917,0.167 0.917,0.167 1.083,0.167 true 0.927,1.25 1,0.5 1,0.5 1.167,0.5 true 0.51,1.792 0.75,2.25 0.75,2.25 0.917,2.25 true 5.646,1.156 5.583,0.833 5.583,0.833 5.417,0.833 true 1.156,0.073 2.365,0.302 1.208,0.229 10 false Female Connector 1.26,0.406 2.094,0.656 0.833,0.25 10 false Locking Part 1,2.167 2.042,2.417 1.042,0.25 10 false Male Connector 2.958,0.302 4.542,0.573 1.583,0.271 10 false Primary Lock Completed 5.073,0.302 6.844,0.573 1.771,0.271 10 false Secondary Lock Completed 4.833,0.729 5.458,0.906 0.625,0.177 10 false Retainer

i.

This mechanism is designed to detect when the connector is connected only halfway.


ii.

The CPA and female connector slide to the male connector side at the same time and the primary lock is completed when the female connector is engaged with the male connector. From this point, only the CPA slides to the male connector side and secondary lock is completed when the CPA retainer is engaged with the female connector. When the CPA and female connector ends are aligned, they are completely engaged.



g.

Connector lock mechanism (2)

C204951E13
1.135,1.385 1.135,1.813 1.135,1.813 0.854,1.813 true 1.792,3.198 1.792,3.583 1.792,3.583 2.302,3.583 true 4.156,2.76 4.156,3.063 4.156,3.063 3.896,3.063 false 6.115,3.344 5.75,3.344 false 6.458,2.75 6.583,2.75 false 6.323,2.729 6.094,2.729 false 4.385,1.448 4.646,1.448 false 0.458,1.74 0.896,2.115 0.438,0.375 10 false Lance 4.688,1.375 5.208,1.677 0.521,0.302 10 false Holder 2.323,3.521 2.885,3.771 0.563,0.25 10 false Retainer 5.208,3.25 5.854,3.51 0.646,0.26 10 false Retainer 3.344,2.979 3.948,3.323 0.604,0.344 10 false Retainer 5.667,2.656 6.146,2.969 0.479,0.313 10 false Holder 6.625,2.667 7.031,2.917 0.406,0.25 10 false Claw

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Sliding the connector all the way into the holder and locking the lance completes the primary lock.


iii.

Engaging the retainer to the holder as shown in the illustration completes the secondary lock, preventing the connector from accidentally being disconnected.



h.

Improper connection prevention lock mechanism

C204952E23
5.292,0.792 5.292,0.219 5.292,0.219 5.656,0.219 false 5.292,1.167 5.292,1.875 5.292,1.875 4.604,1.875 true 4.958,3.01 4.583,3.01 true 1.104,1.479 1.104,2.396 1.104,2.396 0.948,2.396 true 1.021,1.188 1.021,0.521 1.021,0.521 1.333,0.521 false 6,0.719 6,1.031 6,1.031 5.51,1.031 false 3.958,0.073 4.573,0.448 0.615,0.375 10 false Top View 0.25,2.323 0.958,2.74 0.708,0.417 10 false Unlock Rib 3.917,1.781 4.604,2.333 0.688,0.552 10 false Temporary Hold Lock 4.219,2.927 4.625,3.24 0.406,0.313 10 false Lever 5.698,0.146 6.448,0.438 0.75,0.292 10 false Unlock Rib 1.375,0.448 1.594,0.698 0.219,0.25 10 false A 5.958,0.563 6.219,0.802 0.26,0.24 10 false A

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

When the holder is connected to the airbag sensor assembly, the unlock rib unlocks the temporary hold lock, allowing the lever to be pushed in by rotating around axis A.


iii.

Locking the lever to the holder locks the holder securely.




ACTIVATION PREVENTION MECHANISM


a.

Function of activation prevention mechanism

i.

An activation prevention mechanism is built into the connector of the airbag system squib circuit to prevent accidental airbag and pretensioner deployment.


ii.

This mechanism closes the circuit when the connector is disconnected by bringing the short spring into contact with the terminals and insulating the circuit from external power sources to prevent accidental airbag and pretensioner deployment.



b.

Releasing of activation prevention mechanism

i.

To release the activation prevention mechanism, insert a piece of paper with the same thickness as the male terminal (approximately 0.5 mm (0.0197 in.)) between the terminals and short spring to break the connection.


ii.

Refer to the following illustrations concerning connectors utilizing the activation prevention mechanism and its release method.

CAUTION:

Never release the activation prevention mechanism on the squib connector even when inspecting with the squib disconnected.


NOTICE:
·

Do not release the activation prevention mechanism unless specified by the troubleshooting procedure.

·

To prevent the terminals and short spring from being damaged, always use a piece of paper with the same thickness as the male terminal.



w/o Dual-stage SRS:
C247429E25
1.594,0.458 1.927,0.677 0.333,0.219 3.719,0.458 4.073,0.688 0.354,0.229 5.354,0.458 5.719,0.688 0.365,0.229 0.146,5.042 0.479,5.26 0.333,0.219 0.708,6.135 1.042,6.354 0.333,0.219 2.792,2.781 3.167,2.26 3.167,2.26 2.802,2.479 false 2.198,2.854 1.771,3.281 1.771,3.281 2.198,2.563 true 5.188,2.573 4.719,3.302 4.719,3.302 5.188,2.875 true 5.656,2.781 6.083,2.219 6.083,2.219 5.677,2.479 false 6.229,4.813 6.313,4.448 6.313,4.448 6.375,4.448 false 4.073,4.813 4.198,4.427 4.198,4.427 4.26,4.427 false 5.417,4.76 5.417,5.51 true 3.313,4.75 3.313,5.5 true 3.875,6.531 3.781,6.531 3.781,6.531 3.667,6.875 false 3.125,7.01 3.313,7.365 3.313,7.365 3.385,7.365 true 6.594,6.531 6.5,6.531 6.5,6.531 6.385,6.875 false 5.844,7.01 6.021,7.365 6.021,7.365 6.104,7.365 true 1.521,1.865 2.469,2.208 0.948,0.344 10 false Before Release 4.615,1.865 5.49,2.229 0.875,0.365 10 false After Release 3.198,2.146 3.604,2.5 0.406,0.354 10 false Paper 6.115,2.135 6.531,2.625 0.417,0.49 10 false Paper 1.375,3.281 2.198,3.604 0.823,0.323 10 false Short Spring 4.313,3.333 5.125,3.688 0.813,0.354 10 false Short Spring 1.656,0.49 2.708,0.854 1.052,0.365 10 false F70 0.094,0.063 4.115,0.344 4.021,0.281 12 false Wire harness connector (to Airbag Sensor Assembly): 2.938,4.125 3.906,4.479 0.969,0.354 10 false Before Release 2.521,6.156 3.531,6.552 1.01,0.396 10 false Before Release 5.208,4.125 6.104,4.479 0.896,0.354 10 false After Release 5.188,6.167 6.031,6.542 0.844,0.375 10 false After Release 3.896,6.427 4.302,6.792 0.406,0.365 10 false Paper 4.281,4.344 4.781,4.74 0.5,0.396 10 false Paper 6.396,4.365 6.906,4.823 0.51,0.458 10 false Paper 3.406,7.271 4.24,7.667 0.833,0.396 10 false Short Spring 2.927,5.51 3.74,5.958 0.813,0.448 10 false Short Spring 5.021,5.531 5.844,5.938 0.823,0.406 10 false Short Spring 6.615,6.427 7.031,6.813 0.417,0.385 10 false Paper 6.125,7.271 6.969,7.656 0.844,0.385 10 false Short Spring 0.094,3.75 4.365,4.052 4.271,0.302 12 false Spiral Cable with Sensor Sub-assembly Connector: 0.115,5.802 3.604,6.115 3.49,0.313 12 false No. 2 Instrument Panel Wire Connector: 0.542,7.458 1.625,7.802 1.083,0.344 10 false : Short Spring 3.813,0.49 4.865,0.854 1.052,0.365 10 false M2 5.417,0.49 6.469,0.854 1.052,0.365 10 false M17 0.208,5.073 1.26,5.438 1.052,0.365 10 false F30 0.76,6.167 1.813,6.531 1.052,0.365 10 false FX2

w/ Dual-stage SRS:
C247452E28
1.75,0.49 2.125,0.74 0.375,0.25 3.417,0.49 3.75,0.74 0.333,0.25 5.083,0.49 5.417,0.74 0.333,0.25 0.156,5.01 0.49,5.229 0.333,0.219 0.677,6.271 1.01,6.49 0.333,0.219 3.094,2.823 3.469,2.302 3.469,2.302 3.063,2.51 false 2.479,2.917 2.104,3.333 2.104,3.333 2.49,2.615 true 5.042,2.625 4.604,3.354 4.604,3.354 5.052,2.938 true 5.5,2.823 5.979,2.271 5.979,2.271 5.521,2.51 false 6.229,4.76 6.313,4.396 6.313,4.396 6.375,4.396 false 4.01,4.76 4.135,4.365 4.135,4.365 4.198,4.365 false 3.927,6.563 3.833,6.563 3.833,6.563 3.74,6.938 false 6.49,6.573 6.396,6.573 6.396,6.573 6.313,6.938 false 3.271,7.063 3.469,7.281 3.469,7.281 3.552,7.281 true 5.813,7.052 6.021,7.281 6.021,7.281 6.094,7.281 true 5.417,4.708 5.417,5.469 true 3.26,4.719 3.26,5.469 true 0.083,0.052 4.438,0.323 4.354,0.271 12 false Wire harness connector (to Airbag Sensor Assembly): 1.833,1.917 2.792,2.25 0.958,0.333 10 false Before Release 4.479,1.917 5.365,2.292 0.885,0.375 10 false After Release 3.49,2.198 3.875,2.5 0.385,0.302 10 false Paper 5.99,2.188 6.385,2.594 0.396,0.406 10 false Paper 1.719,3.333 2.49,3.677 0.771,0.344 10 false Short Spring 4.198,3.385 4.979,3.719 0.781,0.333 10 false Short Spring 2.938,4.073 3.885,4.333 0.948,0.26 10 false Before Release 2.521,6.229 3.479,6.521 0.958,0.292 10 false Before Release 5.198,4.073 6.104,4.396 0.906,0.323 10 false After Release 5.115,6.229 5.979,6.521 0.865,0.292 10 false After Release 3.969,6.5 4.396,6.771 0.427,0.271 10 false Paper 4.229,4.313 4.635,4.469 0.406,0.156 10 false Paper 6.531,6.5 6.948,6.802 0.417,0.302 10 false Paper 6.417,4.323 6.844,4.604 0.427,0.281 10 false Paper 3.604,7.198 4.375,7.542 0.771,0.344 10 false Short Spring 6.135,7.198 6.917,7.542 0.781,0.344 10 false Short Spring 0.083,3.688 4.542,4.021 4.458,0.333 12 false Spiral Cable with Sensor Sub-assembly Connector: 0.083,5.844 3.5,6.177 3.417,0.333 12 false No. 2 Instrument Panel Wire Connector: 0.521,7.469 1.406,7.76 0.885,0.292 10 false : Short Spring 2.896,5.458 3.688,5.802 0.792,0.344 10 false Short Spring 5.021,5.479 5.813,5.813 0.792,0.333 10 false Short Spring 1.813,0.531 2.229,0.771 0.417,0.24 10 false M18 3.469,0.531 3.885,0.771 0.417,0.24 10 false F70 5.167,0.531 5.583,0.771 0.417,0.24 10 false M1 0.208,5.042 0.625,5.281 0.417,0.24 10 false F30 0.74,6.302 1.156,6.542 0.417,0.24 10 false FX1