Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _060061 SUPPLEMENTAL RESTRAINT SYSTEMS _0294190 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light Remains ON  


DESCRIPTION

The SRS warning light is located in the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

If a malfunction occurs in the airbag sensor assembly, combination meter assembly or wire harness connected to the airbag sensor assembly or combination meter assembly, the SRS warning light comes on.

When terminals TC and CG of the DLC3 are connected, DTCs are displayed by blinking of the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag sensor assembly in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage. In addition, when the voltage drops, the SRS warning light will illuminate.

A malfunction in this circuit is not stored in the airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the airbag sensor assembly to the combination meter assembly via CAN communication.

WIRING DIAGRAM

C263701E65
0.667,1.792 1.563,2.031 0.896,0.24 10 false from Battery 4.906,0.729 5.781,0.979 0.875,0.25 10 false A/BAG-IG2 2.094,1.417 3.135,1.708 1.042,0.292 10 false METER-IG2 1.958,1.969 3.25,2.333 1.292,0.365 10 false ECU-DCC NO. 2 3.094,2.365 3.396,2.635 0.302,0.271 10 false ET 2.854,1.719 3.125,2.01 0.271,0.292 10 false 40 2.865,1.177 3.188,1.427 0.323,0.25 10 false 39 2.854,2.271 3.25,2.594 0.396,0.323 10 false 21 6.052,0.594 6.427,0.906 0.375,0.313 10 false IG2 3.615,1.26 4.302,1.583 0.688,0.323 10 false CANH 3.635,1.823 4.25,2.177 0.615,0.354 10 false CANL 6.063,2.365 6.354,2.625 0.292,0.26 10 false E1 6.063,2.875 6.354,3.125 0.292,0.25 10 false E2 6.01,3.615 6.521,3.906 0.51,0.292 10 false F70 3.042,3.604 3.448,3.854 0.406,0.25 10 false F4 6.01,3.771 6.948,4.24 0.938,0.469 10 false Airbag Sensor Assembly 3.042,3.771 4.24,4.333 1.198,0.563 10 false Combination Meter Assembly 6.052,1.26 6.583,1.5 0.531,0.24 10 false CANH 6.052,1.802 6.552,2.021 0.5,0.219 10 false CANL 5.802,0.49 6.25,0.781 0.448,0.292 10 false 21 5.813,2.271 6.208,2.521 0.396,0.25 10 false 25 5.813,2.781 6.104,2.979 0.292,0.198 10 false 26 3.104,1.813 3.406,2.031 0.302,0.219 10 false B 3.104,1.26 3.479,1.49 0.375,0.229 10 false IG+ 0.74,4.177 2.51,4.479 1.771,0.302 10 false : CAN Communication Line 2.938,0.573 4.448,0.885 1.51,0.313 10 false from IG2-NO. 2 Relay 0.115,1.229 1.823,1.604 1.708,0.375 10 false from IG2-NO. 2 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CHECK SRS WARNING LIGHT OPERATION
a.

Turn the ignition switch ON and check the SRS warning light condition.

HINT:

The primary check is performed for approximately 6 seconds after the ignition switch is turned ON.



Result:
Result Proceed to
After the primary check period, the SRS warning light remains on. A
After the primary check period, the SRS warning light goes off and comes on again. B



A

2.CHECK BATTERY VOLTAGE

B

6.CHECK CAN COMMUNICATION SYSTEM
2.CHECK BATTERY VOLTAGE
a.

Measure the voltage of the battery.

Standard Voltage:

11 to 14 V



Result:
Result Proceed to
OK A
NG (for 8NR-FTS) B
NG (for 3ZR-FAE) C



A

3.CHECK CONNECTOR

B

C

3.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connector is properly connected to the airbag sensor assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not properly connected, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the airbag sensor assembly.


e.

Check that the terminals of the connector are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

4.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)

NG

REPLACE WIRE HARNESS

4.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)
a.
C126715C56
0.427,0.833 0.813,1.083 0.385,0.25 1.292,1.302 0.854,1.708 true 1.656,1.313 1.219,1.708 true 1.75,1.313 2.188,1.719 true 0.115,0.073 0.396,0.438 0.281,0.365 10 false *a 0.51,0.885 0.885,1.208 0.375,0.323 10 false F70 0.729,1.719 1.135,2.073 0.406,0.354 10 false IG2 1.125,1.729 1.49,2.063 0.365,0.333 10 false E1 2.146,1.729 2.521,2 0.375,0.271 10 false E2
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch ON.


c.

Operate all components of the electrical systems (defogger, wipers, headlights, heater blower, etc.).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F70-21 (IG2) - Body ground Ignition switch ON 8 to 16 V



e.

Turn the ignition switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F70-25 (E1) - Body ground Always Below 1 Ω
F70-26 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK SRS WARNING LIGHT

NG

REPLACE WIRE HARNESS

5.CHECK SRS WARNING LIGHT
a.

Turn the ignition switch ON and check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light turns off for approximately 10 seconds and then turns back on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned ON.



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY

6.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

OK:

CAN communication system is functioning normally.


HINT:

Refer to CAN Bus Check in CAN Communication System.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



Result:
Proceed to
OK
NG



OK

7.CHECK BATTERY VOLTAGE

NG

7.CHECK BATTERY VOLTAGE
a.

Measure the voltage of the battery.

Standard Voltage:

11 to 14 V



Result:
Result Proceed to
OK A
NG (for 8NR-FTS) B
NG (for 3ZR-FAE) C



A

8.CHECK CONNECTOR

B

C

8.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connector is properly connected to the airbag sensor assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not properly connected, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the airbag sensor assembly.


e.

Check that the terminals of the connector are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

9.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)

NG

REPLACE WIRE HARNESS

9.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)
a.
C126715C57
0.427,0.833 0.813,1.083 0.385,0.25 1.292,1.302 0.854,1.708 true 1.646,1.313 1.208,1.708 true 1.75,1.313 2.188,1.719 true 0.115,0.073 0.396,0.438 0.281,0.365 10 false *a 0.51,0.885 0.885,1.208 0.375,0.323 10 false F70 0.729,1.719 1.135,2.073 0.406,0.354 10 false IG2 1.125,1.729 1.49,2.063 0.365,0.333 10 false E1 2.146,1.729 2.521,2 0.375,0.271 10 false E2
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch ON.


c.

Operate all components of the electrical systems (defogger, wipers, headlights, heater blower, etc.).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F70-21 (IG2) - Body ground Ignition switch ON 8 to 16 V



e.

Turn the ignition switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F70-25 (E1) - Body ground Always Below 1 Ω
F70-26 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK CONNECTOR

NG

REPLACE WIRE HARNESS

10.CHECK CONNECTOR
a.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



b.

Check that the connector is properly connected to the combination meter assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not properly connected, reconnect the connector and proceed to the next inspection.



c.

Disconnect the connector from the combination meter assembly.


d.

Check that the terminals of the connector are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

11.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE CONNECTOR

11.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)
a.
C241761C42
0.25,0.417 0.667,0.667 0.417,0.25 2.615,2.021 2.927,1.76 true 3.167,1.958 3.073,1.76 true 0.865,1.677 0.583,1.427 true 0.083,0.052 0.51,0.406 0.427,0.354 10 false *a 2.365,1.99 2.729,2.156 0.365,0.167 10 false IG+ 3.177,1.979 3.375,2.146 0.198,0.167 10 false B 0.344,1.323 0.646,1.594 0.302,0.271 10 false ET 0.385,0.458 0.76,0.74 0.375,0.281 10 false F4
*a Front view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-39 (IG+) - Body ground Ignition switch ON 11 to 14 V
F4-40 (B) - Body ground Ignition switch off 11 to 14 V



d.

Turn the ignition switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-21 (ET) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK SRS WARNING LIGHT

NG

REPAIR OR REPLACE WIRE HARNESS

12.CHECK SRS WARNING LIGHT
a.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



b.

Connect the connector to the combination meter assembly.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch ON and check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light turns off for approximately 10 seconds and then turns back on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned ON.



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY