Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _060061 SUPPLEMENTAL RESTRAINT SYSTEMS _0294190 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1825/56  Short in Side Squib LH Circuit  B1826/56  Open in Side Squib LH Circuit  B1827/56  Short to GND in Side Squib LH Circuit  B1828/56  Short to B+ in Side Squib LH Circuit  


DESCRIPTION

The side squib LH circuit consists of the airbag sensor assembly and front seat airbag assembly LH.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the side squib LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1825/56 Short in Side Squib LH Circuit Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side squib LH circuit during the primary check.

·

Side squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side squib LH (Front seat airbag assembly LH)

·

Airbag sensor assembly


Applies to check mode
B1826/56 Open in Side Squib LH Circuit Any of the following conditions is met:
·

The airbag sensor assembly detects an open in the side squib LH circuit.

·

Side squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side squib LH (Front seat airbag assembly LH)

·

Airbag sensor assembly


Applies to check mode
B1827/56 Short to GND in Side Squib LH Circuit Any of the following conditions is met:
·

The airbag sensor assembly detects a short to ground in the side squib LH circuit.

·

Side squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side squib LH (Front seat airbag assembly LH)

·

Airbag sensor assembly


Applies to check mode
B1828/56 Short to B+ in Side Squib LH Circuit Any of the following conditions is met:
·

The airbag sensor assembly detects a short to B+ in the side squib LH circuit.

·

Side squib LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side squib LH (Front seat airbag assembly LH)

·

Airbag sensor assembly


Applies to check mode

DTC Detection Conditions (B1825/56):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Ignition switch ON ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side squib LH circuit during the primary check ○ - -
Side squib LH malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

DTC Detection Conditions (B1826/56):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Ignition switch ON ○ ○ ○
Malfunction Status The airbag sensor assembly detects an open in the side squib LH circuit ○ - -
Side squib LH malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

DTC Detection Conditions (B1827/56):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Ignition switch ON ○ ○ ○
Malfunction Status The airbag sensor assembly detects a short to ground in the side squib LH circuit ○ - -
Side squib LH malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

DTC Detection Conditions (B1828/56):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Ignition switch ON ○ ○ ○
Malfunction Status The airbag sensor assembly detects a short to B+ in the side squib LH circuit ○ - -
Side squib LH malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C323678E44
1.979,1.052 2.49,1.292 0.51,0.24 10 false SFL+ 2,1.885 2.51,2.125 0.51,0.24 10 false SFL- 4.688,1.99 5.198,2.229 0.51,0.24 10 false SFL- 4.688,1.156 5.198,1.396 0.51,0.24 10 false SFL+ 2.417,1.042 2.615,1.271 0.198,0.229 10 false 1 2.406,1.885 2.604,2.115 0.198,0.229 10 false 2 4.083,1.063 4.969,1.365 0.885,0.302 10 false 9*1, 1*2 4.021,1.896 5.021,2.24 1,0.344 10 false 10*1, 2*2 0.708,2.51 1.219,2.75 0.51,0.24 10 false M3 0.708,2.688 3.75,2.99 3.042,0.302 10 false Side Squib LH (Front Seat Airbag Assembly LH) 4.667,3.021 5.781,3.302 1.115,0.281 10 false M2*1, M1*2 4.677,3.188 6.604,3.531 1.927,0.344 10 false Airbag Sensor Assembly 0.208,3.458 3.208,3.792 3,0.333 10 false *2: w/ Dual-stage SRS 0.208,3.125 3.208,3.458 3,0.333 10 false *1: w/o Dual-stage SRS

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C284699C02
0.49,1.219 0.49,1.719 false 0.49,3.51 0.49,4.01 false 1.344,1.063 1.344,0.604 1.344,0.604 1.479,0.604 false 1.344,3.365 1.344,2.906 1.344,2.906 1.479,2.906 false 0.125,0.125 0.5,0.365 0.375,0.24 10 false *A 0.135,2.438 0.51,2.677 0.375,0.24 10 false *B 0.396,1.74 0.719,1.948 0.323,0.208 10 false *1 2.427,1.063 2.74,1.26 0.313,0.198 10 false *2 1.521,0.521 1.833,0.719 0.313,0.198 10 false *3 0.406,4.031 0.719,4.229 0.313,0.198 10 false *1 2.427,3.667 2.74,3.865 0.313,0.198 10 false *2 1.521,2.823 1.833,3.021 0.313,0.198 10 false *3 2,1.063 2.156,1.26 0.156,0.198 10 false A 1.594,1.063 1.75,1.26 0.156,0.198 10 false B 1.021,1.063 1.177,1.26 0.156,0.198 10 false C 0.615,1.063 0.771,1.26 0.156,0.198 10 false D 2,3.354 2.156,3.552 0.156,0.198 10 false A 1.594,3.354 1.75,3.552 0.156,0.198 10 false B 1.021,3.354 1.177,3.552 0.156,0.198 10 false C 0.615,3.354 0.771,3.552 0.156,0.198 10 false D
*A w/o Dual-stage SRS
*B w/ Dual-stage SRS
*1 Front Seat Airbag Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat airbag assembly LH and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat airbag assembly LH and airbag sensor assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT SEAT AIRBAG ASSEMBLY LH

NG

REPLACE FLOOR WIRE

2.CHECK FRONT SEAT AIRBAG ASSEMBLY LH
a.

Connect the connector to the airbag sensor assembly.

C316518C03
0.76,1.844 1.094,2.063 0.333,0.219 4.354,1.844 4.688,2.063 0.333,0.219 0.896,0.479 0.896,0.146 0.896,0.146 1.063,0.146 false 4.479,0.583 4.479,0.333 false 2.469,2.01 2.219,2.01 false 6.052,2.01 5.802,2.01 false 0.448,0.083 0.792,0.344 0.344,0.26 10 false *A 4.01,0.083 4.406,0.333 0.396,0.25 10 false *B 4.417,0.604 4.729,0.927 0.313,0.323 10 false *1 2.427,0.448 2.823,0.865 0.396,0.417 10 false *2 4.292,1.344 4.688,1.667 0.396,0.323 10 false *a 1.104,0.063 1.417,0.385 0.313,0.323 10 false *1 6.01,0.458 6.406,0.875 0.396,0.417 10 false *2 0.708,1.333 1.104,1.75 0.396,0.417 10 false *a 2.51,1.927 2.906,2.333 0.396,0.406 10 false SST 6.094,1.927 6.49,2.333 0.396,0.406 10 false SST 0.844,1.875 1.24,2.281 0.396,0.406 10 false M3 4.438,1.875 4.833,2.281 0.396,0.406 10 false M3 2.052,0.458 2.448,0.875 0.396,0.417 10 false A 1.917,0.458 2.313,0.875 0.396,0.417 10 false B 1.313,0.458 1.708,0.875 0.396,0.417 10 false C 1,0.458 1.396,0.875 0.396,0.417 10 false D 5.635,0.198 6.031,0.615 0.396,0.417 10 false A 5.5,0.198 5.896,0.615 0.396,0.417 10 false B 4.896,0.198 5.292,0.615 0.396,0.417 10 false C 4.583,0.198 4.979,0.615 0.396,0.417 10 false D
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Front Seat Airbag Assembly LH *2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Seat Airbag Assembly LH)
- -



b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the front seat airbag assembly LH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1825/56, B1826/56, B1827/56 or B1828/56 is not output.


HINT:

Codes other than DTCs B1825/56, B1826/56, B1827/56 and B1828/56 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.


Result:
Proceed to
OK
NG



OK

NG

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.

Disconnect the floor wire from the airbag sensor assembly.

C316519C03
0.708,1.844 1.042,2.063 0.333,0.219 4.25,1.844 4.583,2.063 0.333,0.219 0.667,0.563 0.667,0.229 0.667,0.229 0.833,0.229 false 4.24,0.74 4.24,0.406 false 1.49,0.563 1.49,0.229 1.49,0.229 1.656,0.229 false 5.094,0.75 5.094,0.417 false 1.146,2.354 1.458,1.969 true 1.927,2.354 1.625,1.969 true 4.74,2.354 5.052,1.969 true 5.521,2.354 5.219,1.969 true 0.323,0.094 0.656,0.333 0.333,0.24 10 false *A 3.875,0.083 4.375,0.417 0.5,0.333 10 false *B 0.865,0.135 1.344,0.458 0.479,0.323 10 false *1 6.115,0.552 6.531,0.969 0.417,0.417 10 false *2 1.688,0.146 2.25,0.646 0.563,0.5 10 false *3 0.615,1.417 0.927,1.75 0.313,0.333 10 false *a 4.177,0.76 4.656,1.083 0.479,0.323 10 false *1 5.031,0.76 5.594,1.26 0.563,0.5 10 false *3 2.542,0.542 2.958,0.875 0.417,0.333 10 false *2 4.198,1.417 4.51,1.75 0.313,0.333 10 false *a 0.771,1.865 1.083,2.198 0.313,0.333 10 false M3 2.135,0.552 2.552,0.885 0.417,0.333 10 false A 1.781,0.552 2.198,0.885 0.417,0.333 10 false B 1.125,0.552 1.542,0.885 0.417,0.333 10 false C 0.76,0.552 1.177,0.885 0.417,0.333 10 false D 5.719,0.271 6.135,0.604 0.417,0.333 10 false A 5.365,0.271 5.781,0.604 0.417,0.333 10 false B 4.698,0.271 5.115,0.604 0.417,0.333 10 false C 4.344,0.271 4.76,0.604 0.417,0.333 10 false D 4.313,1.854 4.625,2.188 0.313,0.333 10 false M3 0.99,2.354 1.438,2.698 0.448,0.344 10 false SFL+ 1.792,2.354 2.24,2.698 0.448,0.344 10 false SFL- 4.583,2.354 5.031,2.698 0.448,0.344 10 false SFL+ 5.406,2.354 5.854,2.698 0.448,0.344 10 false SFL-
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Front Seat Airbag Assembly LH *2 Airbag Sensor Assembly
*3 Floor Wire - -
*a Front view of wire harness connector
(to Front Seat Airbag Assembly LH)
- -



b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M3-1 (SFL+) - Body ground Ignition switch ON Below 1 V
M3-2 (SFL-) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M3-1 (SFL+) - M3-2 (SFL-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M3-1 (SFL+) - Body ground Always 1 MΩ or higher
M3-2 (SFL-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M3-1 (SFL+) - M3-2 (SFL-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C284702C02
0.781,1.26 0.781,1.667 false 0.781,3.302 0.781,3.708 false 0.125,0.135 0.5,0.375 0.375,0.24 10 false *A 0.115,2.281 0.49,2.521 0.375,0.24 10 false *B 0.688,1.688 1,1.885 0.313,0.198 10 false *1 0.688,3.74 1,3.938 0.313,0.198 10 false *1 2.135,1.115 2.448,1.313 0.313,0.198 10 false *2 2.146,3.458 2.458,3.656 0.313,0.198 10 false *2 1.729,1.115 1.885,1.313 0.156,0.198 10 false A 1.563,1.115 1.719,1.313 0.156,0.198 10 false B 1.063,1.115 1.219,1.313 0.156,0.198 10 false C 0.906,1.115 1.063,1.313 0.156,0.198 10 false D 1.729,3.146 1.885,3.344 0.156,0.198 10 false A 1.563,3.146 1.719,3.344 0.156,0.198 10 false B 1.063,3.146 1.219,3.344 0.156,0.198 10 false C 0.906,3.146 1.063,3.344 0.156,0.198 10 false D
*A w/o Dual-stage SRS
*B w/ Dual-stage SRS
*1 Front Seat Airbag Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the front seat airbag assembly LH and airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1825/56, B1826/56, B1827/56 or B1828/56 is not output.


HINT:

Codes other than DTCs B1825/56, B1826/56, B1827/56 and B1828/56 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG