Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _060061 SUPPLEMENTAL RESTRAINT SYSTEMS _0294190 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1622/81  Lost communication with Side Airbag Sensor RH  B1623/81  Side Airbag Sensor Assembly RH Initialization Incomplete  B1632/81  Lost Communication with Rear Airbag Sensor RH  B1633/81  Rear Airbag Sensor Assembly RH Initialization Incomplete  B1642/81  Lost Communication with Side Satellite Sensor Bus RH  B1643/81  Side Satellite Sensor Bus RH Initialization Incomplete  B166D/81  Lost Communication with Front Door Pressure Sensor RH  B166E/81  Front Door Pressure Sensor RH Initialization Incomplete  


DESCRIPTION

The side collision sensor RH circuit (bus 1) consists of the airbag sensor assembly, door side airbag sensor RH, No. 1 side airbag sensor RH and No. 2 side airbag sensor RH.

The door side airbag sensor RH, No. 1 side airbag sensor RH and No. 2 side airbag sensor RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit (bus 1).

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1622/81 Lost communication with Side Airbag Sensor RH Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1).

·

No. 1 side airbag sensor RH malfunction

·

No. 2 side airbag sensor RH malfunction

·

Door side airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire RH

·

No. 1 side airbag sensor RH

·

No. 2 side airbag sensor RH

·

Door side airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode
B1623/81 Side Airbag Sensor Assembly RH Initialization Incomplete Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1).

·

No. 1 side airbag sensor RH malfunction

·

No. 2 side airbag sensor RH malfunction

·

Door side airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire RH

·

No. 1 side airbag sensor RH

·

No. 2 side airbag sensor RH

·

Door side airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode
B1632/81 Lost Communication with Rear Airbag Sensor RH Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1).

·

No. 1 side airbag sensor RH malfunction

·

No. 2 side airbag sensor RH malfunction

·

Door side airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire RH

·

No. 1 side airbag sensor RH

·

No. 2 side airbag sensor RH

·

Door side airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode
B1633/81 Rear Airbag Sensor Assembly RH Initialization Incomplete Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1).

·

No. 1 side airbag sensor RH malfunction

·

No. 2 side airbag sensor RH malfunction

·

Door side airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire RH

·

No. 1 side airbag sensor RH

·

No. 2 side airbag sensor RH

·

Door side airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode
B1642/81 Lost Communication with Side Satellite Sensor Bus RH Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1).

·

No. 1 side airbag sensor RH malfunction

·

No. 2 side airbag sensor RH malfunction

·

Door side airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire RH

·

No. 1 side airbag sensor RH

·

No. 2 side airbag sensor RH

·

Door side airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode
B1643/81 Side Satellite Sensor Bus RH Initialization Incomplete Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1).

·

No. 1 side airbag sensor RH malfunction

·

No. 2 side airbag sensor RH malfunction

·

Door side airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire RH

·

No. 1 side airbag sensor RH

·

No. 2 side airbag sensor RH

·

Door side airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode
B166D/81 Lost Communication with Front Door Pressure Sensor RH Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1).

·

No. 1 side airbag sensor RH malfunction

·

No. 2 side airbag sensor RH malfunction

·

Door side airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire RH

·

No. 1 side airbag sensor RH

·

No. 2 side airbag sensor RH

·

Door side airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode
B166E/81 Front Door Pressure Sensor RH Initialization Incomplete Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1).

·

No. 1 side airbag sensor RH malfunction

·

No. 2 side airbag sensor RH malfunction

·

Door side airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire RH

·

No. 1 side airbag sensor RH

·

No. 2 side airbag sensor RH

·

Door side airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode

DTC Detection Conditions (B1622/81):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Ignition switch ON ○ ○ ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1) ○ - - - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1) - ○ - - - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1) - - ○ - - - - -
The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1) - - - ○ - - - -
No. 1 side airbag sensor RH malfunction - - - - ○ - - -
No. 2 side airbag sensor RH malfunction - - - - - ○ - -
Door side airbag sensor RH malfunction - - - - - - ○ -
Airbag sensor assembly malfunction - - - - - - - ○
Detection Time - - - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B1623/81):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Ignition switch ON ○ ○ ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1) ○ - - - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1) - ○ - - - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1) - - ○ - - - - -
The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1) - - - ○ - - - -
No. 1 side airbag sensor RH malfunction - - - - ○ - - -
No. 2 side airbag sensor RH malfunction - - - - - ○ - -
Door side airbag sensor RH malfunction - - - - - - ○ -
Airbag sensor assembly malfunction - - - - - - - ○
Detection Time - - - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B1632/81):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Ignition switch ON ○ ○ ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1) ○ - - - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1) - ○ - - - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1) - - ○ - - - - -
The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1) - - - ○ - - - -
No. 1 side airbag sensor RH malfunction - - - - ○ - - -
No. 2 side airbag sensor RH malfunction - - - - - ○ - -
Door side airbag sensor RH malfunction - - - - - - ○ -
Airbag sensor assembly malfunction - - - - - - - ○
Detection Time - - - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B1633/81):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Ignition switch ON ○ ○ ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1) ○ - - - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1) - ○ - - - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1) - - ○ - - - - -
The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1) - - - ○ - - - -
No. 1 side airbag sensor RH malfunction - - - - ○ - - -
No. 2 side airbag sensor RH malfunction - - - - - ○ - -
Door side airbag sensor RH malfunction - - - - - - ○ -
Airbag sensor assembly malfunction - - - - - - - ○
Detection Time - - - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B1642/81):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Ignition switch ON ○ ○ ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1) ○ - - - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1) - ○ - - - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1) - - ○ - - - - -
The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1) - - - ○ - - - -
No. 1 side airbag sensor RH malfunction - - - - ○ - - -
No. 2 side airbag sensor RH malfunction - - - - - ○ - -
Door side airbag sensor RH malfunction - - - - - - ○ -
Airbag sensor assembly malfunction - - - - - - - ○
Detection Time - - - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B1643/81):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Ignition switch ON ○ ○ ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1) ○ - - - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1) - ○ - - - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1) - - ○ - - - - -
The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1) - - - ○ - - - -
No. 1 side airbag sensor RH malfunction - - - - ○ - - -
No. 2 side airbag sensor RH malfunction - - - - - ○ - -
Door side airbag sensor RH malfunction - - - - - - ○ -
Airbag sensor assembly malfunction - - - - - - - ○
Detection Time - - - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B166D/81):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Ignition switch ON ○ ○ ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1) ○ - - - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1) - ○ - - - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1) - - ○ - - - - -
The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1) - - - ○ - - - -
No. 1 side airbag sensor RH malfunction - - - - ○ - - -
No. 2 side airbag sensor RH malfunction - - - - - ○ - -
Door side airbag sensor RH malfunction - - - - - - ○ -
Airbag sensor assembly malfunction - - - - - - - ○
Detection Time - - - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B166E/81):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition Ignition switch ON ○ ○ ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1) ○ - - - - - - -
The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1) - ○ - - - - - -
The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1) - - ○ - - - - -
The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1) - - - ○ - - - -
No. 1 side airbag sensor RH malfunction - - - - ○ - - -
No. 2 side airbag sensor RH malfunction - - - - - ○ - -
Door side airbag sensor RH malfunction - - - - - - ○ -
Airbag sensor assembly malfunction - - - - - - - ○
Detection Time - - - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C238366E97
3.427,4.667 3.969,5.083 0.542,0.417 10 false M57 0.542,2.781 1.688,3.26 1.146,0.479 10 false No. 1 Side Airbag Sensor RH 0.552,4.823 2.417,5.302 1.865,0.479 10 false Door Side Airbag Sensor RH 5.521,4.854 7.156,5.156 1.635,0.302 10 false Airbag Sensor Assembly 5.51,4.688 6.573,4.896 1.063,0.208 10 false M17*1, M18*2 1.146,0.521 1.948,1.083 0.802,0.563 10 false BBR+ 1.594,0.438 2.063,0.938 0.469,0.5 10 false 4 1.167,1.104 1.802,1.604 0.635,0.5 10 false BBR- 4.885,0.438 5.865,0.823 0.979,0.385 10 false 8*1, 17*2 4.823,1 5.688,1.438 0.865,0.438 10 false 11*1, 18*2 1.594,1.01 1.948,1.448 0.354,0.438 10 false 3 1.125,3.792 1.927,4.427 0.802,0.635 10 false BDR+ 2.406,3.594 2.854,4.198 0.448,0.604 10 false 22 1.167,4.354 1.792,4.833 0.625,0.479 10 false BDR- 2.406,4.146 2.76,4.563 0.354,0.417 10 false 40 2.375,3.792 3.031,4.354 0.656,0.563 10 false IM1 2.375,4.333 2.927,4.854 0.552,0.521 10 false IM1 0.552,4.667 1.146,5.073 0.594,0.406 10 false I5 3.427,4.823 4.531,5.26 1.104,0.438 10 false No. 2 Side Airbag Sensor RH 0.542,2.625 1.115,3.094 0.573,0.469 10 false M56 3.469,3.802 4.063,4.292 0.594,0.49 10 false BDR+ 3.469,4.333 4.01,4.865 0.542,0.531 10 false BDR- 3.479,1.698 4.063,2.146 0.583,0.448 10 false BCR+ 3.469,2.302 4.031,2.729 0.563,0.427 10 false BCR- 1.135,1.688 1.698,2.083 0.563,0.396 10 false BCR+ 1.167,2.302 1.833,2.792 0.667,0.49 10 false BCR- 5.563,0.542 6.135,1 0.573,0.458 10 false BBR+ 5.563,1.115 6.021,1.656 0.458,0.542 10 false BBR- 1.594,1.604 2.063,2.271 0.469,0.667 10 false 1 1.594,2.208 2.083,2.688 0.49,0.479 10 false 2 3.292,1.604 3.75,2.073 0.458,0.469 10 false 4 3.292,2.177 3.875,2.74 0.583,0.563 10 false 3 3.313,3.698 3.771,4.135 0.458,0.438 10 false 1 3.313,4.24 3.802,4.792 0.49,0.552 10 false 2 1.594,3.698 2.021,4.323 0.427,0.625 10 false 2 1.594,4.24 2.021,4.813 0.427,0.573 10 false 1 0.219,5.198 2.969,5.521 2.75,0.323 10 false *1: w/o Dual-stage SRS 0.219,5.5 2.969,5.823 2.75,0.323 10 false *2: w/ Dual-stage SRS

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CURRENT DTC
a.

Check for current DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch off and then ON again.

·

Codes other than current DTCs B1622, B1623, B1632, B1633, B1642, B1643, B166D, B166E and 81 may be output at this time, but they are not related to this check.




Result:
Result Proceed to
Current DTC B1642, B1643 or 81 is output. A
Current DTC B1623 is output. B
Current DTC B1633 is output. C
Current DTC B166D or B166E is output. D
Current DTC B1622 is output. E
Current DTC B1632 is output. F
Current DTCs B1622, B1623, B1632, B1633, B1642, B1643, B166D, B166E and 81 are not output. G



A

2.CHECK CONNECTORS

B

22.CHECK HISTORY DTC

C

42.CHECK HISTORY DTC

D

51.CHECK CONNECTORS

E

62.CHECK NO. 1 SIDE AIRBAG SENSOR RH

F

63.CHECK NO. 2 SIDE AIRBAG SENSOR RH

G

2.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, No. 1 side airbag sensor RH, No. 2 side airbag sensor RH and door side airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, No. 1 side airbag sensor RH, No. 2 side airbag sensor RH and door side airbag sensor RH. Also disconnect the connectors that link the floor wire and front door wire RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE (OPEN)

NG

REPLACE WIRE HARNESS

3.CHECK FLOOR WIRE (OPEN)
a.

w/o Dual-stage SRS

Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

w/ Dual-stage SRS

Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



C348398C02
2.677,2.865 2.99,3.073 0.313,0.208 1.677,0.438 2.01,0.646 0.333,0.208 3.75,0.438 4.083,0.646 0.333,0.208 3.5,2.021 3.5,1.604 3.5,1.604 3.333,1.604 false 2.313,1.177 2.313,1.01 false 4.344,1.167 4.344,1.042 false 1.927,0.99 2.198,0.802 true 2.729,0.99 2.375,0.594 true 4.708,1 4.396,0.771 true 3.938,0.99 4.292,0.771 true 3.896,3.396 3.625,3.031 true 3.313,3.406 3.531,3.042 true 1.75,0.25 2.25,0.583 0.5,0.333 10 false *A 3.833,0.25 4.25,0.49 0.417,0.24 10 false *B 2.75,2.01 3.146,2.417 0.396,0.406 10 false *1 4.219,1.76 4.698,2.167 0.479,0.406 10 false *2 3.177,1.531 3.573,1.781 0.396,0.25 10 false *3 2.25,1.177 2.667,1.51 0.417,0.333 10 false *4 1.448,0.177 1.844,0.5 0.396,0.323 10 false *a 2.51,2.625 2.927,2.958 0.417,0.333 10 false *b 4.281,1.177 4.698,1.51 0.417,0.333 10 false *4 2.708,2.885 3.125,3.219 0.417,0.333 10 false M56 3.792,3.417 4.208,3.698 0.417,0.281 10 false BBR+ 3.156,3.417 3.573,3.698 0.417,0.281 10 false BBR- 2.594,1 3.083,1.25 0.49,0.25 10 false BBR+ 1.781,1 2.229,1.333 0.448,0.333 10 false BBR- 3.75,1 4.24,1.25 0.49,0.25 10 false BBR+ 4.583,1 5.031,1.333 0.448,0.333 10 false BBR- 1.719,0.469 2.167,0.802 0.448,0.333 10 false M17 3.792,0.458 4.24,0.792 0.448,0.333 10 false M18 3.896,2.01 4.375,2.417 0.479,0.406 10 false A 3.646,2.01 4.125,2.417 0.479,0.406 10 false B 3.281,2.01 3.76,2.417 0.479,0.406 10 false C 3.021,2.01 3.5,2.417 0.479,0.406 10 false D
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 No. 1 Side Airbag Sensor RH *2 Airbag Sensor Assembly
*3 Floor Wire *4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M56-4 (BBR+) - M56-3 (BBR-) Always Below 1 Ω



d.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

4.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT)
a.
C238220C72
0.406,2.26 0.781,2.521 0.375,0.26 1.51,2.448 1.26,2.823 true 1.656,2.448 1.896,2.823 true 1.542,0.958 1.542,0.354 1.542,0.354 1.313,0.354 false 0.958,0.958 1.24,1.323 0.281,0.365 10 false D 1.271,0.948 1.677,1.417 0.406,0.469 10 false C 1.729,0.948 2.083,1.375 0.354,0.427 10 false B 2.031,0.958 2.427,1.438 0.396,0.479 10 false A 0.646,0.958 0.938,1.313 0.292,0.354 10 false *1 2.448,0.688 2.833,1.073 0.385,0.385 10 false *2 1.146,0.281 1.51,0.656 0.365,0.375 10 false *3 0.333,1.75 0.667,2.115 0.333,0.365 10 false *a 0.479,2.302 0.938,2.625 0.458,0.323 10 false M56 1.083,2.844 1.698,3.177 0.615,0.333 10 false BBR- 1.75,2.844 2.26,3.094 0.51,0.25 10 false BBR+
*1 No. 1 Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M56-4 (BBR+) - M56-3 (BBR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT TO B+)
a.
C238220C72
0.406,2.26 0.781,2.521 0.375,0.26 1.51,2.448 1.26,2.823 true 1.656,2.448 1.896,2.823 true 1.542,0.958 1.542,0.354 1.542,0.354 1.313,0.354 false 0.958,0.958 1.24,1.323 0.281,0.365 10 false D 1.271,0.948 1.677,1.417 0.406,0.469 10 false C 1.729,0.948 2.083,1.375 0.354,0.427 10 false B 2.031,0.958 2.427,1.438 0.396,0.479 10 false A 0.646,0.958 0.938,1.313 0.292,0.354 10 false *1 2.448,0.688 2.833,1.073 0.385,0.385 10 false *2 1.146,0.281 1.51,0.656 0.365,0.375 10 false *3 0.333,1.75 0.667,2.115 0.333,0.365 10 false *a 0.479,2.302 0.938,2.625 0.458,0.323 10 false M56 1.083,2.844 1.698,3.177 0.615,0.333 10 false BBR- 1.75,2.844 2.26,3.094 0.51,0.25 10 false BBR+
*1 No. 1 Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M56-4 (BBR+) - Body ground Ignition switch ON Below 1 V
M56-3 (BBR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

6.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

6.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C238220C72
0.406,2.26 0.781,2.521 0.375,0.26 1.51,2.448 1.26,2.823 true 1.656,2.448 1.896,2.823 true 1.542,0.958 1.542,0.354 1.542,0.354 1.313,0.354 false 0.958,0.958 1.24,1.323 0.281,0.365 10 false D 1.271,0.948 1.677,1.417 0.406,0.469 10 false C 1.729,0.948 2.083,1.375 0.354,0.427 10 false B 2.031,0.958 2.427,1.438 0.396,0.479 10 false A 0.646,0.958 0.938,1.313 0.292,0.354 10 false *1 2.448,0.688 2.833,1.073 0.385,0.385 10 false *2 1.146,0.281 1.51,0.656 0.365,0.375 10 false *3 0.333,1.75 0.667,2.115 0.333,0.365 10 false *a 0.479,2.302 0.938,2.625 0.458,0.323 10 false M56 1.083,2.844 1.698,3.177 0.615,0.333 10 false BBR- 1.75,2.844 2.26,3.094 0.51,0.25 10 false BBR+
*1 No. 1 Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M56-4 (BBR+) - Body ground Always 1 MΩ or higher
M56-3 (BBR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

7.CHECK FLOOR WIRE (OPEN)
a.
C238392C25
0.469,3.542 0.833,3.792 0.365,0.25 0.896,0.542 1.271,0.781 0.375,0.24 1.823,0.708 1.49,1.031 true 1.948,0.708 2.281,1.031 true 1.708,2.344 1.708,1.865 1.708,1.865 1.531,1.865 false 1.542,3.656 1.208,4.031 true 1.646,3.667 2,4.031 true 1.594,4.031 1.594,4.313 false 1.177,2.323 1.406,2.677 0.229,0.354 10 false D 1.479,2.323 1.781,2.594 0.302,0.271 10 false C 1.833,2.313 2.073,2.667 0.24,0.354 10 false B 2.146,2.313 2.406,2.698 0.26,0.385 10 false A 0.792,2.323 1.219,2.563 0.427,0.24 10 false *1 0.625,0.188 0.948,0.521 0.323,0.333 10 false *a 0.354,3.208 0.76,3.563 0.406,0.354 10 false *b 1.031,4.042 1.49,4.313 0.458,0.271 10 false BCR- 1.896,4.052 2.406,4.313 0.51,0.26 10 false BCR+ 0.531,3.583 0.948,3.906 0.417,0.323 10 false M57 0.958,0.583 1.313,0.896 0.354,0.313 10 false M56 2.188,1.042 2.688,1.323 0.5,0.281 10 false BCR- 1.313,1.052 1.865,1.365 0.552,0.313 10 false BCR+ 1.375,1.792 1.74,2.156 0.365,0.365 10 false *3 2.448,2.323 2.74,2.698 0.292,0.375 10 false *2 1.531,4.333 1.802,4.594 0.271,0.26 10 false *4
*1 No. 2 Side Airbag Sensor RH
*2 No. 1 Side Airbag Sensor RH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH)


Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M56-1 (BCR+) - M56-2 (BCR-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

8.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

8.CHECK FLOOR WIRE (SHORT)
a.
C368460C01
1.083,2.333 1.583,2.583 0.5,0.25 1.729,0.74 1.5,0.344 false 2.5,2.833 2.24,2.469 true 1.917,2.833 2.073,2.469 true 0.771,0.74 1.083,0.896 0.313,0.156 10 false *1 2.521,0.74 2.833,0.896 0.313,0.156 10 false *2 1.333,0.198 1.646,0.354 0.313,0.156 10 false *3 1,1.896 1.313,2.052 0.313,0.156 10 false *a 1.198,2.365 1.594,2.531 0.396,0.167 10 false M56 1.604,2.854 2.188,3.104 0.583,0.25 10 false BCR+ 2.469,2.865 3.052,3.031 0.583,0.167 10 false BCR- 1.156,0.74 1.385,0.906 0.229,0.167 10 false D 1.458,0.74 1.688,0.906 0.229,0.167 10 false C 1.906,0.74 2.135,0.906 0.229,0.167 10 false B 2.219,0.729 2.448,0.896 0.229,0.167 10 false A
*1 No. 2 Side Airbag Sensor RH
*2 No. 1 Side Airbag Sensor RH
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M56-1 (BCR+) - M56-2 (BCR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

9.CHECK FLOOR WIRE (SHORT TO B+)
a.
C368460C01
1.083,2.333 1.583,2.583 0.5,0.25 1.729,0.74 1.5,0.344 false 2.5,2.833 2.24,2.469 true 1.917,2.833 2.073,2.469 true 0.771,0.74 1.083,0.896 0.313,0.156 10 false *1 2.521,0.74 2.833,0.896 0.313,0.156 10 false *2 1.333,0.198 1.646,0.354 0.313,0.156 10 false *3 1,1.896 1.313,2.052 0.313,0.156 10 false *a 1.198,2.365 1.594,2.531 0.396,0.167 10 false M56 1.604,2.854 2.188,3.104 0.583,0.25 10 false BCR+ 2.469,2.865 3.052,3.031 0.583,0.167 10 false BCR- 1.156,0.74 1.385,0.906 0.229,0.167 10 false D 1.458,0.74 1.688,0.906 0.229,0.167 10 false C 1.906,0.74 2.135,0.906 0.229,0.167 10 false B 2.219,0.729 2.448,0.896 0.229,0.167 10 false A
*1 No. 2 Side Airbag Sensor RH
*2 No. 1 Side Airbag Sensor RH
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M56-1 (BCR+) - Body ground Ignition switch ON Below 1 V
M56-2 (BCR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

10.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

10.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C368460C01
1.083,2.333 1.583,2.583 0.5,0.25 1.729,0.74 1.5,0.344 false 2.5,2.833 2.24,2.469 true 1.917,2.833 2.073,2.469 true 0.771,0.74 1.083,0.896 0.313,0.156 10 false *1 2.521,0.74 2.833,0.896 0.313,0.156 10 false *2 1.333,0.198 1.646,0.354 0.313,0.156 10 false *3 1,1.896 1.313,2.052 0.313,0.156 10 false *a 1.198,2.365 1.594,2.531 0.396,0.167 10 false M56 1.604,2.854 2.188,3.104 0.583,0.25 10 false BCR+ 2.469,2.865 3.052,3.031 0.583,0.167 10 false BCR- 1.156,0.74 1.385,0.906 0.229,0.167 10 false D 1.458,0.74 1.688,0.906 0.229,0.167 10 false C 1.906,0.74 2.135,0.906 0.229,0.167 10 false B 2.219,0.729 2.448,0.896 0.229,0.167 10 false A
*1 No. 2 Side Airbag Sensor RH
*2 No. 1 Side Airbag Sensor RH
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M56-1 (BCR+) - Body ground Always 1 MΩ or higher
M56-2 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK WIRE HARNESS (OPEN)

NG

REPLACE FLOOR WIRE

11.CHECK WIRE HARNESS (OPEN)
a.
C284683C17
0.792,0.573 1.135,0.813 0.344,0.24 0.542,3.625 0.865,3.854 0.323,0.229 2.333,1.083 1.917,0.667 true 1.01,4.167 1.385,3.75 true 2.042,4.167 1.625,3.75 true 1.354,1.083 1.771,0.667 true 1.844,1.302 1.844,1.094 false 0.552,2.313 0.917,2.625 0.365,0.313 10 false *1 2.74,2.333 3.063,2.75 0.323,0.417 10 false *2 1.781,1.313 2.135,1.615 0.354,0.302 10 false *3 0.635,0.167 0.979,0.583 0.344,0.417 10 false *a 0.344,3.156 0.625,3.583 0.281,0.427 10 false *b 2.396,2.333 2.719,2.75 0.323,0.417 10 false A 2.083,2.333 2.406,2.75 0.323,0.417 10 false B 1.74,2.333 2.063,2.75 0.323,0.417 10 false C 1.583,2.333 1.906,2.75 0.323,0.417 10 false D 1.24,2.323 1.563,2.74 0.323,0.417 10 false E 0.927,2.323 1.25,2.74 0.323,0.417 10 false F 1.188,1.104 1.604,1.521 0.417,0.417 10 false BDR+ 2.229,1.104 2.646,1.521 0.417,0.417 10 false BDR- 1.885,4.167 2.302,4.5 0.417,0.333 10 false BDR+ 0.844,4.167 1.26,4.604 0.417,0.438 10 false BDR- 0.844,0.615 1.26,1.031 0.417,0.417 10 false M57 0.656,3.667 1.073,4.083 0.417,0.417 10 false I5
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor RH)


Connect the connectors that link the floor wire and front door wire RH.


b.

Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-2 (BDR+) - I5-1 (BDR-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK WIRE HARNESS (SHORT)

NG

21.CHECK FLOOR WIRE (OPEN)
12.CHECK WIRE HARNESS (SHORT)
a.
C284684C17
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 true 2.25,2.75 1.792,2.313 true 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDR- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDR+ 0.823,2.229 1.219,2.583 0.396,0.354 10 false I5
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*a Front view of wire harness connector
(to Door Side Airbag Sensor RH)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-2 (BDR+) - I5-1 (BDR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK WIRE HARNESS (SHORT TO B+)

NG

20.CHECK FLOOR WIRE (SHORT)
13.CHECK WIRE HARNESS (SHORT TO B+)
a.
C284684C17
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 true 2.25,2.75 1.792,2.313 true 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDR- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDR+ 0.823,2.229 1.219,2.583 0.396,0.354 10 false I5
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*a Front view of wire harness connector
(to Door Side Airbag Sensor RH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I5-2 (BDR+) - Body ground Ignition switch ON Below 1 V
I5-1 (BDR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

14.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

19.CHECK FLOOR WIRE (SHORT TO B+)
14.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C284684C17
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 true 2.25,2.75 1.792,2.313 true 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDR- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDR+ 0.823,2.229 1.219,2.583 0.396,0.354 10 false I5
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*a Front view of wire harness connector
(to Door Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-2 (BDR+) - Body ground Always 1 MΩ or higher
I5-1 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

15.CHECK NO. 1 SIDE AIRBAG SENSOR RH

NG

18.CHECK FLOOR WIRE (SHORT TO GROUND)
15.CHECK NO. 1 SIDE AIRBAG SENSOR RH
a.
C238218C01
0.802,1.188 1.094,1.479 0.292,0.292 10 false *1 1.115,1.167 1.281,1.448 0.167,0.281 10 false D 1.271,1.167 1.458,1.438 0.188,0.271 10 false C 1.719,1.177 1.948,1.5 0.229,0.323 10 false B 1.875,1.177 2.094,1.396 0.219,0.219 10 false A 2.302,0.906 2.625,1.198 0.323,0.292 10 false *2
*1 No. 1 Side Airbag Sensor LH
*2 Airbag Sensor Assembly


Connect the connectors to the No. 2 side airbag sensor RH, door side airbag sensor RH and airbag sensor assembly.


b.

Interchange the No. 1 side airbag sensor RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1642, B1643 or 81 is output. A
DTC B1647, B1648 or 82 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the No. 1 side airbag sensor RH and LH to their original positions and connect the connectors.



A

16.CHECK NO. 2 SIDE AIRBAG SENSOR RH

B

C

16.CHECK NO. 2 SIDE AIRBAG SENSOR RH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 No. 2 Side Airbag Sensor LH
*2 No. 1 Side Airbag Sensor RH


Interchange the No. 2 side airbag sensor RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1642, B1643 or 81 is output. A
DTC B1647, B1648 or 82 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the No. 2 side airbag sensor RH and LH to their original positions and connect the connectors.



A

17.CHECK DOOR SIDE AIRBAG SENSOR RH

B

C

17.CHECK DOOR SIDE AIRBAG SENSOR RH
a.
C238395C02
0.719,1.021 1.51,1.656 0.792,0.635 10 false *1 2.552,1 2.906,1.406 0.354,0.406 10 false *2 2.26,1.021 2.531,1.51 0.271,0.49 10 false A 2.104,1.021 2.531,1.563 0.427,0.542 10 false B 1.76,1.021 2.24,1.583 0.479,0.563 10 false C 1.604,1.021 2.031,1.615 0.427,0.594 10 false D 1.26,1.021 1.708,1.625 0.448,0.604 10 false E 1.115,1.021 1.792,1.771 0.677,0.75 10 false F
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor RH


Interchange the door side airbag sensor RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1642, B1643 or 81 is output. A
DTC B1647, B1648 or 82 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the door side airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C

18.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C284682C24
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 true 1.406,2.479 1.667,3 true 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.604,1.521 0.917,1.76 0.313,0.24 10 false IM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDR+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDR-
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Front Door Wire RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire RH)


Disconnect the floor wire connector from the front door wire RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IM1-22 (BDR+) - Body ground Always 1 MΩ or higher
IM1-40 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE

19.CHECK FLOOR WIRE (SHORT TO B+)
a.
C284682C24
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 true 1.406,2.479 1.667,3 true 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.604,1.521 0.917,1.76 0.313,0.24 10 false IM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDR+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDR-
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Front Door Wire RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire RH)


Disconnect the floor wire connector from the front door wire RH.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
IM1-22 (BDR+) - Body ground Ignition switch ON Below 1 V
IM1-40 (BDR-) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE

20.CHECK FLOOR WIRE (SHORT)
a.
C284682C24
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 true 1.406,2.479 1.667,3 true 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.604,1.521 0.917,1.76 0.313,0.24 10 false IM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDR+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDR-
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Front Door Wire RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire RH)


Disconnect the floor wire connector from the front door wire RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IM1-22 (BDR+) - IM1-40 (BDR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE

21.CHECK FLOOR WIRE (OPEN)
a.
C284681C17
0.865,0.563 1.219,0.792 0.354,0.229 0.458,2.823 0.823,3.042 0.365,0.219 1.781,4.302 1.406,3.771 true 1.844,1.344 1.844,1.094 false 1.333,1.167 1.771,0.667 true 2.333,1.167 1.917,0.667 true 1.333,2.229 1.333,2.479 false 1.906,1.771 2.073,1.771 2.073,1.771 2.073,2.104 false 1,4.313 1.406,3.635 true 0.417,2.083 0.813,2.49 0.396,0.406 10 false *1 2.865,2.094 3.26,2.667 0.396,0.573 10 false *2 1.271,2.479 1.604,2.719 0.333,0.24 10 false *3 1.75,1.698 2.146,2.031 0.396,0.333 10 false *4 1.781,1.354 2.198,1.677 0.417,0.323 10 false *5 0.604,0.167 1,0.583 0.396,0.417 10 false *a 0.156,2.833 0.552,3.24 0.396,0.406 10 false *b 2.542,2.083 2.938,2.656 0.396,0.573 10 false A 2.24,2.083 2.635,2.656 0.396,0.573 10 false B 1.813,2.083 2.208,2.656 0.396,0.573 10 false C 1.521,2.083 1.917,2.656 0.396,0.573 10 false D 1.094,2.083 1.49,2.656 0.396,0.573 10 false E 0.792,2.083 1.188,2.656 0.396,0.573 10 false F 1.177,1.167 1.677,1.5 0.5,0.333 10 false BDR+ 2.198,1.167 2.698,1.5 0.5,0.333 10 false BDR- 0.844,4.302 1.344,4.635 0.5,0.333 10 false BDR+ 1.667,4.302 2.167,4.635 0.5,0.333 10 false BDR- 0.927,0.594 1.427,0.927 0.5,0.333 10 false M57 0.542,2.854 1.042,3.188 0.5,0.333 10 false IM1
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH)
*b Front view of wire harness connector
(to Front Door Wire RH)


Disconnect the floor wire connector from the front door wire RH.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IM1-22 (BDR+) - IM1-40 (BDR-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE

22.CHECK HISTORY DTC
a.

Check for history DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than history DTC B1622 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
History DTC B1622 is not output. A
History DTC B1622 is output. B



A

23.CHECK CONNECTORS

B

41.CHECK NO. 1 SIDE AIRBAG SENSOR RH
23.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, No. 1 side airbag sensor RH, No. 2 side airbag sensor RH and door side airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, No. 1 side airbag sensor RH, No. 2 side airbag sensor RH and door side airbag sensor RH. Also disconnect the connectors that link the floor wire and front door wire RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

24.CHECK FLOOR WIRE (OPEN)

NG

REPLACE WIRE HARNESS

24.CHECK FLOOR WIRE (OPEN)
a.

w/o Dual-stage SRS

Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

w/ Dual-stage SRS

Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



C348398C03
2.677,2.865 2.99,3.073 0.313,0.208 1.677,0.438 2.01,0.646 0.333,0.208 3.75,0.438 4.083,0.646 0.333,0.208 3.5,2.021 3.5,1.604 3.5,1.604 3.333,1.604 false 2.313,1.177 2.313,1.01 false 4.344,1.167 4.344,1.042 false 1.927,0.99 2.198,0.802 true 2.729,0.99 2.375,0.594 true 4.708,1 4.396,0.771 true 3.938,0.99 4.292,0.771 true 3.906,3.406 3.635,3.042 true 3.313,3.406 3.531,3.042 false 1.75,0.25 2.25,0.583 0.5,0.333 10 false *A 3.833,0.25 4.25,0.49 0.417,0.24 10 false *B 2.75,2.01 3.146,2.417 0.396,0.406 10 false *1 4.219,1.76 4.698,2.167 0.479,0.406 10 false *2 3.177,1.531 3.573,1.781 0.396,0.25 10 false *3 2.25,1.177 2.667,1.51 0.417,0.333 10 false *4 1.448,0.177 1.844,0.5 0.396,0.323 10 false *a 2.51,2.625 2.927,2.958 0.417,0.333 10 false *b 4.281,1.177 4.698,1.51 0.417,0.333 10 false *4 2.708,2.885 3.125,3.219 0.417,0.333 10 false M56 3.792,3.417 4.208,3.698 0.417,0.281 10 false BBR+ 3.156,3.417 3.573,3.698 0.417,0.281 10 false BBR- 2.594,1 3.083,1.25 0.49,0.25 10 false BBR+ 1.781,1 2.229,1.333 0.448,0.333 10 false BBR- 3.75,1 4.24,1.25 0.49,0.25 10 false BBR+ 4.583,1 5.031,1.333 0.448,0.333 10 false BBR- 1.719,0.469 2.167,0.802 0.448,0.333 10 false M17 3.792,0.458 4.24,0.792 0.448,0.333 10 false M18 3.896,2.01 4.375,2.417 0.479,0.406 10 false A 3.646,2.01 4.125,2.417 0.479,0.406 10 false B 3.281,2.01 3.76,2.417 0.479,0.406 10 false C 3.021,2.01 3.5,2.417 0.479,0.406 10 false D
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 No. 1 Side Airbag Sensor RH *2 Airbag Sensor Assembly
*3 Floor Wire *4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M56-4 (BBR+) - M56-3 (BBR-) Always Below 1 Ω



d.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

25.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

25.CHECK FLOOR WIRE (SHORT)
a.
C238220C73
0.406,2.26 0.781,2.521 0.375,0.26 1.51,2.448 1.26,2.823 true 1.656,2.448 1.896,2.823 true 1.542,0.958 1.542,0.354 1.542,0.354 1.313,0.354 false 0.958,0.958 1.24,1.323 0.281,0.365 10 false D 1.271,0.948 1.677,1.417 0.406,0.469 10 false C 1.729,0.948 2.083,1.375 0.354,0.427 10 false B 2.031,0.958 2.427,1.438 0.396,0.479 10 false A 0.646,0.958 0.938,1.313 0.292,0.354 10 false *1 2.448,0.688 2.833,1.073 0.385,0.385 10 false *2 1.146,0.281 1.51,0.656 0.365,0.375 10 false *3 0.333,1.75 0.667,2.115 0.333,0.365 10 false *a 0.479,2.302 0.938,2.625 0.458,0.323 10 false M56 1.083,2.844 1.698,3.177 0.615,0.333 10 false BBR- 1.75,2.844 2.26,3.094 0.51,0.25 10 false BBR+
*1 No. 1 Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M56-4 (BBR+) - M56-3 (BBR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

26.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

26.CHECK FLOOR WIRE (SHORT TO B+)
a.
C238220C73
0.406,2.26 0.781,2.521 0.375,0.26 1.51,2.448 1.26,2.823 true 1.656,2.448 1.896,2.823 true 1.542,0.958 1.542,0.354 1.542,0.354 1.313,0.354 false 0.958,0.958 1.24,1.323 0.281,0.365 10 false D 1.271,0.948 1.677,1.417 0.406,0.469 10 false C 1.729,0.948 2.083,1.375 0.354,0.427 10 false B 2.031,0.958 2.427,1.438 0.396,0.479 10 false A 0.646,0.958 0.938,1.313 0.292,0.354 10 false *1 2.448,0.688 2.833,1.073 0.385,0.385 10 false *2 1.146,0.281 1.51,0.656 0.365,0.375 10 false *3 0.333,1.75 0.667,2.115 0.333,0.365 10 false *a 0.479,2.302 0.938,2.625 0.458,0.323 10 false M56 1.083,2.844 1.698,3.177 0.615,0.333 10 false BBR- 1.75,2.844 2.26,3.094 0.51,0.25 10 false BBR+
*1 No. 1 Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M56-4 (BBR+) - Body ground Ignition switch ON Below 1 V
M56-3 (BBR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

27.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

27.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C238220C73
0.406,2.26 0.781,2.521 0.375,0.26 1.51,2.448 1.26,2.823 true 1.656,2.448 1.896,2.823 true 1.542,0.958 1.542,0.354 1.542,0.354 1.313,0.354 false 0.958,0.958 1.24,1.323 0.281,0.365 10 false D 1.271,0.948 1.677,1.417 0.406,0.469 10 false C 1.729,0.948 2.083,1.375 0.354,0.427 10 false B 2.031,0.958 2.427,1.438 0.396,0.479 10 false A 0.646,0.958 0.938,1.313 0.292,0.354 10 false *1 2.448,0.688 2.833,1.073 0.385,0.385 10 false *2 1.146,0.281 1.51,0.656 0.365,0.375 10 false *3 0.333,1.75 0.667,2.115 0.333,0.365 10 false *a 0.479,2.302 0.938,2.625 0.458,0.323 10 false M56 1.083,2.844 1.698,3.177 0.615,0.333 10 false BBR- 1.75,2.844 2.26,3.094 0.51,0.25 10 false BBR+
*1 No. 1 Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M56-4 (BBR+) - Body ground Always 1 MΩ or higher
M56-3 (BBR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

28.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

28.CHECK FLOOR WIRE (OPEN)
a.
C238392C26
0.469,3.542 0.833,3.792 0.365,0.25 0.896,0.542 1.271,0.781 0.375,0.24 1.823,0.708 1.49,1.031 true 1.948,0.708 2.281,1.031 true 1.708,2.344 1.708,1.865 1.708,1.865 1.531,1.865 false 1.542,3.656 1.208,4.031 true 1.646,3.667 2,4.031 true 1.594,4.031 1.594,4.313 false 1.177,2.323 1.406,2.677 0.229,0.354 10 false D 1.479,2.323 1.781,2.594 0.302,0.271 10 false C 1.833,2.313 2.073,2.667 0.24,0.354 10 false B 2.146,2.313 2.406,2.698 0.26,0.385 10 false A 0.792,2.323 1.219,2.563 0.427,0.24 10 false *1 0.625,0.188 0.948,0.521 0.323,0.333 10 false *a 0.354,3.208 0.76,3.563 0.406,0.354 10 false *b 1.031,4.042 1.49,4.313 0.458,0.271 10 false BCR- 1.896,4.052 2.406,4.313 0.51,0.26 10 false BCR+ 0.531,3.583 0.948,3.906 0.417,0.323 10 false M57 0.958,0.583 1.313,0.896 0.354,0.313 10 false M56 2.188,1.042 2.688,1.323 0.5,0.281 10 false BCR- 1.313,1.052 1.865,1.365 0.552,0.313 10 false BCR+ 1.375,1.792 1.74,2.156 0.365,0.365 10 false *3 2.448,2.323 2.74,2.698 0.292,0.375 10 false *2 1.531,4.333 1.802,4.594 0.271,0.26 10 false *4
*1 No. 2 Side Airbag Sensor RH
*2 No. 1 Side Airbag Sensor RH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH)


Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M56-1 (BCR+) - M56-2 (BCR-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

29.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

29.CHECK FLOOR WIRE (SHORT)
a.
C368460C01
1.083,2.333 1.583,2.583 0.5,0.25 1.729,0.74 1.5,0.344 false 2.5,2.833 2.24,2.469 true 1.917,2.833 2.073,2.469 true 0.771,0.74 1.083,0.896 0.313,0.156 10 false *1 2.521,0.74 2.833,0.896 0.313,0.156 10 false *2 1.333,0.198 1.646,0.354 0.313,0.156 10 false *3 1,1.896 1.313,2.052 0.313,0.156 10 false *a 1.198,2.365 1.594,2.531 0.396,0.167 10 false M56 1.604,2.854 2.188,3.104 0.583,0.25 10 false BCR+ 2.469,2.865 3.052,3.031 0.583,0.167 10 false BCR- 1.156,0.74 1.385,0.906 0.229,0.167 10 false D 1.458,0.74 1.688,0.906 0.229,0.167 10 false C 1.906,0.74 2.135,0.906 0.229,0.167 10 false B 2.219,0.729 2.448,0.896 0.229,0.167 10 false A
*1 No. 2 Side Airbag Sensor RH
*2 No. 1 Side Airbag Sensor RH
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M56-1 (BCR+) - M56-2 (BCR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

30.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

30.CHECK FLOOR WIRE (SHORT TO B+)
a.
C368460C01
1.083,2.333 1.583,2.583 0.5,0.25 1.729,0.74 1.5,0.344 false 2.5,2.833 2.24,2.469 true 1.917,2.833 2.073,2.469 true 0.771,0.74 1.083,0.896 0.313,0.156 10 false *1 2.521,0.74 2.833,0.896 0.313,0.156 10 false *2 1.333,0.198 1.646,0.354 0.313,0.156 10 false *3 1,1.896 1.313,2.052 0.313,0.156 10 false *a 1.198,2.365 1.594,2.531 0.396,0.167 10 false M56 1.604,2.854 2.188,3.104 0.583,0.25 10 false BCR+ 2.469,2.865 3.052,3.031 0.583,0.167 10 false BCR- 1.156,0.74 1.385,0.906 0.229,0.167 10 false D 1.458,0.74 1.688,0.906 0.229,0.167 10 false C 1.906,0.74 2.135,0.906 0.229,0.167 10 false B 2.219,0.729 2.448,0.896 0.229,0.167 10 false A
*1 No. 2 Side Airbag Sensor RH
*2 No. 1 Side Airbag Sensor RH
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M56-1 (BCR+) - Body ground Ignition switch ON Below 1 V
M56-2 (BCR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

31.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

31.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C368460C01
1.083,2.333 1.583,2.583 0.5,0.25 1.729,0.74 1.5,0.344 false 2.5,2.833 2.24,2.469 true 1.917,2.833 2.073,2.469 true 0.771,0.74 1.083,0.896 0.313,0.156 10 false *1 2.521,0.74 2.833,0.896 0.313,0.156 10 false *2 1.333,0.198 1.646,0.354 0.313,0.156 10 false *3 1,1.896 1.313,2.052 0.313,0.156 10 false *a 1.198,2.365 1.594,2.531 0.396,0.167 10 false M56 1.604,2.854 2.188,3.104 0.583,0.25 10 false BCR+ 2.469,2.865 3.052,3.031 0.583,0.167 10 false BCR- 1.156,0.74 1.385,0.906 0.229,0.167 10 false D 1.458,0.74 1.688,0.906 0.229,0.167 10 false C 1.906,0.74 2.135,0.906 0.229,0.167 10 false B 2.219,0.729 2.448,0.896 0.229,0.167 10 false A
*1 No. 2 Side Airbag Sensor RH
*2 No. 1 Side Airbag Sensor RH
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M56-1 (BCR+) - Body ground Always 1 MΩ or higher
M56-2 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

32.CHECK WIRE HARNESS (OPEN)

NG

REPLACE FLOOR WIRE

32.CHECK WIRE HARNESS (OPEN)
a.
C284683C18
0.792,0.573 1.135,0.813 0.344,0.24 0.542,3.625 0.865,3.854 0.323,0.229 2.333,1.083 1.917,0.667 true 1.01,4.167 1.385,3.75 true 2.042,4.167 1.625,3.75 true 1.354,1.083 1.771,0.667 true 1.844,1.302 1.844,1.094 false 0.552,2.313 0.917,2.625 0.365,0.313 10 false *1 2.74,2.333 3.063,2.75 0.323,0.417 10 false *2 1.781,1.313 2.135,1.615 0.354,0.302 10 false *3 0.635,0.167 0.979,0.583 0.344,0.417 10 false *a 0.344,3.156 0.625,3.583 0.281,0.427 10 false *b 2.396,2.333 2.719,2.75 0.323,0.417 10 false A 2.083,2.333 2.406,2.75 0.323,0.417 10 false B 1.74,2.333 2.063,2.75 0.323,0.417 10 false C 1.583,2.333 1.906,2.75 0.323,0.417 10 false D 1.24,2.323 1.563,2.74 0.323,0.417 10 false E 0.927,2.323 1.25,2.74 0.323,0.417 10 false F 1.188,1.104 1.604,1.521 0.417,0.417 10 false BDR+ 2.229,1.104 2.646,1.521 0.417,0.417 10 false BDR- 1.885,4.167 2.302,4.5 0.417,0.333 10 false BDR+ 0.844,4.167 1.26,4.604 0.417,0.438 10 false BDR- 0.844,0.615 1.26,1.031 0.417,0.417 10 false M57 0.656,3.667 1.073,4.083 0.417,0.417 10 false I5
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor RH)


Connect the connectors that link the floor wire and front door wire RH.


b.

Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-2 (BDR+) - I5-1 (BDR-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

33.CHECK WIRE HARNESS (SHORT)

NG

40.CHECK FLOOR WIRE (OPEN)
33.CHECK WIRE HARNESS (SHORT)
a.
C284684C17
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 true 2.25,2.75 1.792,2.313 true 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDR- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDR+ 0.823,2.229 1.219,2.583 0.396,0.354 10 false I5
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*a Front view of wire harness connector
(to Door Side Airbag Sensor RH)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-2 (BDR+) - I5-1 (BDR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

34.CHECK WIRE HARNESS (SHORT TO B+)

NG

39.CHECK FLOOR WIRE (SHORT)
34.CHECK WIRE HARNESS (SHORT TO B+)
a.
C284684C17
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 true 2.25,2.75 1.792,2.313 true 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDR- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDR+ 0.823,2.229 1.219,2.583 0.396,0.354 10 false I5
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*a Front view of wire harness connector
(to Door Side Airbag Sensor RH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I5-2 (BDR+) - Body ground Ignition switch ON Below 1 V
I5-1 (BDR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

35.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

38.CHECK FLOOR WIRE (SHORT TO B+)
35.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C284684C17
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 true 2.25,2.75 1.792,2.313 true 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDR- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDR+ 0.823,2.229 1.219,2.583 0.396,0.354 10 false I5
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*a Front view of wire harness connector
(to Door Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-2 (BDR+) - Body ground Always 1 MΩ or higher
I5-1 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

36.CHECK NO. 1 SIDE AIRBAG SENSOR RH

NG

37.CHECK FLOOR WIRE (SHORT TO GROUND)
36.CHECK NO. 1 SIDE AIRBAG SENSOR RH
a.
C238218C01
0.802,1.188 1.094,1.479 0.292,0.292 10 false *1 1.115,1.167 1.281,1.448 0.167,0.281 10 false D 1.271,1.167 1.458,1.438 0.188,0.271 10 false C 1.719,1.177 1.948,1.5 0.229,0.323 10 false B 1.875,1.177 2.094,1.396 0.219,0.219 10 false A 2.302,0.906 2.625,1.198 0.323,0.292 10 false *2
*1 No. 1 Side Airbag Sensor LH
*2 Airbag Sensor Assembly


Connect the connectors to the No. 2 side airbag sensor RH, door side airbag sensor RH and airbag sensor assembly.


b.

Interchange the No. 1 side airbag sensor RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1623 is output. A
DTC B1628 is output. B
DTCs B1623 and B1628 are not output. C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the No. 1 side airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C

37.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C284682C24
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 true 1.406,2.479 1.667,3 true 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.604,1.521 0.917,1.76 0.313,0.24 10 false IM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDR+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDR-
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Front Door Wire RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire RH)


Disconnect the floor wire connector from the front door wire RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IM1-22 (BDR+) - Body ground Always 1 MΩ or higher
IM1-40 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE

38.CHECK FLOOR WIRE (SHORT TO B+)
a.
C284682C24
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 true 1.406,2.479 1.667,3 true 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.604,1.521 0.917,1.76 0.313,0.24 10 false IM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDR+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDR-
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Front Door Wire RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire RH)


Disconnect the floor wire connector from the front door wire RH.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
IM1-22 (BDR+) - Body ground Ignition switch ON Below 1 V
IM1-40 (BDR-) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE

39.CHECK FLOOR WIRE (SHORT)
a.
C284682C24
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 true 1.406,2.479 1.667,3 true 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.604,1.521 0.917,1.76 0.313,0.24 10 false IM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDR+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDR-
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Front Door Wire RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire RH)


Disconnect the floor wire connector from the front door wire RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IM1-22 (BDR+) - IM1-40 (BDR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE

40.CHECK FLOOR WIRE (OPEN)
a.
C284681C17
0.865,0.563 1.219,0.792 0.354,0.229 0.458,2.823 0.823,3.042 0.365,0.219 1.781,4.302 1.406,3.771 true 1.844,1.344 1.844,1.094 false 1.333,1.167 1.771,0.667 true 2.333,1.167 1.917,0.667 true 1.333,2.229 1.333,2.479 false 1.906,1.771 2.073,1.771 2.073,1.771 2.073,2.104 false 1,4.313 1.406,3.635 true 0.417,2.083 0.813,2.49 0.396,0.406 10 false *1 2.865,2.094 3.26,2.667 0.396,0.573 10 false *2 1.271,2.479 1.604,2.719 0.333,0.24 10 false *3 1.75,1.698 2.146,2.031 0.396,0.333 10 false *4 1.781,1.354 2.198,1.677 0.417,0.323 10 false *5 0.604,0.167 1,0.583 0.396,0.417 10 false *a 0.156,2.833 0.552,3.24 0.396,0.406 10 false *b 2.542,2.083 2.938,2.656 0.396,0.573 10 false A 2.24,2.083 2.635,2.656 0.396,0.573 10 false B 1.813,2.083 2.208,2.656 0.396,0.573 10 false C 1.521,2.083 1.917,2.656 0.396,0.573 10 false D 1.094,2.083 1.49,2.656 0.396,0.573 10 false E 0.792,2.083 1.188,2.656 0.396,0.573 10 false F 1.177,1.167 1.677,1.5 0.5,0.333 10 false BDR+ 2.198,1.167 2.698,1.5 0.5,0.333 10 false BDR- 0.844,4.302 1.344,4.635 0.5,0.333 10 false BDR+ 1.667,4.302 2.167,4.635 0.5,0.333 10 false BDR- 0.927,0.594 1.427,0.927 0.5,0.333 10 false M57 0.542,2.854 1.042,3.188 0.5,0.333 10 false IM1
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH)
*b Front view of wire harness connector
(to Front Door Wire RH)


Disconnect the floor wire connector from the front door wire RH.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IM1-22 (BDR+) - IM1-40 (BDR-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE

41.CHECK NO. 1 SIDE AIRBAG SENSOR RH
a.
C238218C01
0.802,1.188 1.094,1.479 0.292,0.292 10 false *1 1.115,1.167 1.281,1.448 0.167,0.281 10 false D 1.271,1.167 1.458,1.438 0.188,0.271 10 false C 1.719,1.177 1.948,1.5 0.229,0.323 10 false B 1.875,1.177 2.094,1.396 0.219,0.219 10 false A 2.302,0.906 2.625,1.198 0.323,0.292 10 false *2
*1 No. 1 Side Airbag Sensor LH
*2 Airbag Sensor Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the No. 1 side airbag sensor RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1622 is output. A
DTC B1627 is output. B
DTCs B1622 and B1627 are not output. C


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the No. 1 side airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C

42.CHECK HISTORY DTC
a.

Check for history DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than history DTC B1632 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
History DTC B1632 is not output. A
History DTC B1632 is output. B



A

43.CHECK CONNECTORS

B

50.CHECK NO. 2 SIDE AIRBAG SENSOR RH
43.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the No. 1 side airbag sensor RH and No. 2 side airbag sensor RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the No. 1 side airbag sensor RH and No. 2 side airbag sensor RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

44.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

44.CHECK FLOOR WIRE (OPEN)
a.
C238392C25
0.469,3.542 0.833,3.792 0.365,0.25 0.896,0.542 1.271,0.781 0.375,0.24 1.823,0.708 1.49,1.031 true 1.948,0.708 2.281,1.031 true 1.708,2.344 1.708,1.865 1.708,1.865 1.531,1.865 false 1.542,3.656 1.208,4.031 true 1.646,3.667 2,4.031 true 1.594,4.031 1.594,4.313 false 1.177,2.323 1.406,2.677 0.229,0.354 10 false D 1.479,2.323 1.781,2.594 0.302,0.271 10 false C 1.833,2.313 2.073,2.667 0.24,0.354 10 false B 2.146,2.313 2.406,2.698 0.26,0.385 10 false A 0.792,2.323 1.219,2.563 0.427,0.24 10 false *1 0.625,0.188 0.948,0.521 0.323,0.333 10 false *a 0.354,3.208 0.76,3.563 0.406,0.354 10 false *b 1.031,4.042 1.49,4.313 0.458,0.271 10 false BCR- 1.896,4.052 2.406,4.313 0.51,0.26 10 false BCR+ 0.531,3.583 0.948,3.906 0.417,0.323 10 false M57 0.958,0.583 1.313,0.896 0.354,0.313 10 false M56 2.188,1.042 2.688,1.323 0.5,0.281 10 false BCR- 1.313,1.052 1.865,1.365 0.552,0.313 10 false BCR+ 1.375,1.792 1.74,2.156 0.365,0.365 10 false *3 2.448,2.323 2.74,2.698 0.292,0.375 10 false *2 1.531,4.333 1.802,4.594 0.271,0.26 10 false *4
*1 No. 2 Side Airbag Sensor RH
*2 No. 1 Side Airbag Sensor RH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH)


Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M56-1 (BCR+) - M56-2 (BCR-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

45.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

45.CHECK FLOOR WIRE (SHORT)
a.
C368460C01
1.083,2.333 1.583,2.583 0.5,0.25 1.729,0.74 1.5,0.344 false 2.5,2.833 2.24,2.469 true 1.917,2.833 2.073,2.469 true 0.771,0.74 1.083,0.896 0.313,0.156 10 false *1 2.521,0.74 2.833,0.896 0.313,0.156 10 false *2 1.333,0.198 1.646,0.354 0.313,0.156 10 false *3 1,1.896 1.313,2.052 0.313,0.156 10 false *a 1.198,2.365 1.594,2.531 0.396,0.167 10 false M56 1.604,2.854 2.188,3.104 0.583,0.25 10 false BCR+ 2.469,2.865 3.052,3.031 0.583,0.167 10 false BCR- 1.156,0.74 1.385,0.906 0.229,0.167 10 false D 1.458,0.74 1.688,0.906 0.229,0.167 10 false C 1.906,0.74 2.135,0.906 0.229,0.167 10 false B 2.219,0.729 2.448,0.896 0.229,0.167 10 false A
*1 No. 2 Side Airbag Sensor RH
*2 No. 1 Side Airbag Sensor RH
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M56-1 (BCR+) - M56-2 (BCR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

46.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

46.CHECK FLOOR WIRE (SHORT TO B+)
a.
C368460C01
1.083,2.333 1.583,2.583 0.5,0.25 1.729,0.74 1.5,0.344 false 2.5,2.833 2.24,2.469 true 1.917,2.833 2.073,2.469 true 0.771,0.74 1.083,0.896 0.313,0.156 10 false *1 2.521,0.74 2.833,0.896 0.313,0.156 10 false *2 1.333,0.198 1.646,0.354 0.313,0.156 10 false *3 1,1.896 1.313,2.052 0.313,0.156 10 false *a 1.198,2.365 1.594,2.531 0.396,0.167 10 false M56 1.604,2.854 2.188,3.104 0.583,0.25 10 false BCR+ 2.469,2.865 3.052,3.031 0.583,0.167 10 false BCR- 1.156,0.74 1.385,0.906 0.229,0.167 10 false D 1.458,0.74 1.688,0.906 0.229,0.167 10 false C 1.906,0.74 2.135,0.906 0.229,0.167 10 false B 2.219,0.729 2.448,0.896 0.229,0.167 10 false A
*1 No. 2 Side Airbag Sensor RH
*2 No. 1 Side Airbag Sensor RH
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M56-1 (BCR+) - Body ground Ignition switch ON Below 1 V
M56-2 (BCR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

47.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

47.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C368460C01
1.083,2.333 1.583,2.583 0.5,0.25 1.729,0.74 1.5,0.344 false 2.5,2.833 2.24,2.469 true 1.917,2.833 2.073,2.469 true 0.771,0.74 1.083,0.896 0.313,0.156 10 false *1 2.521,0.74 2.833,0.896 0.313,0.156 10 false *2 1.333,0.198 1.646,0.354 0.313,0.156 10 false *3 1,1.896 1.313,2.052 0.313,0.156 10 false *a 1.198,2.365 1.594,2.531 0.396,0.167 10 false M56 1.604,2.854 2.188,3.104 0.583,0.25 10 false BCR+ 2.469,2.865 3.052,3.031 0.583,0.167 10 false BCR- 1.156,0.74 1.385,0.906 0.229,0.167 10 false D 1.458,0.74 1.688,0.906 0.229,0.167 10 false C 1.906,0.74 2.135,0.906 0.229,0.167 10 false B 2.219,0.729 2.448,0.896 0.229,0.167 10 false A
*1 No. 2 Side Airbag Sensor RH
*2 No. 1 Side Airbag Sensor RH
*3 Floor Wire
*a Front view of wire harness connector
(to No. 1 Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M56-1 (BCR+) - Body ground Always 1 MΩ or higher
M56-2 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

48.CHECK NO. 1 SIDE AIRBAG SENSOR RH

NG

REPLACE FLOOR WIRE

48.CHECK NO. 1 SIDE AIRBAG SENSOR RH
a.
C238218C01
0.802,1.188 1.094,1.479 0.292,0.292 10 false *1 1.115,1.167 1.281,1.448 0.167,0.281 10 false D 1.271,1.167 1.458,1.438 0.188,0.271 10 false C 1.719,1.177 1.948,1.5 0.229,0.323 10 false B 1.875,1.177 2.094,1.396 0.219,0.219 10 false A 2.302,0.906 2.625,1.198 0.323,0.292 10 false *2
*1 No. 1 Side Airbag Sensor LH
*2 Airbag Sensor Assembly


Connect the connector to the No. 2 side airbag sensor RH.


b.

Interchange the No. 1 side airbag sensor RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1633 is output. A
DTC B1638 is output. B
DTCs B1633 and B1638 are not output. C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the No. 1 side airbag sensor RH and LH to their original positions and connect the connectors.



A

49.CHECK NO. 2 SIDE AIRBAG SENSOR RH

B

C

49.CHECK NO. 2 SIDE AIRBAG SENSOR RH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 No. 2 Side Airbag Sensor LH
*2 No. 1 Side Airbag Sensor RH


Interchange the No. 2 side airbag sensor RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1633 is output. A
DTC B1638 is output. B
DTCs B1633 and B1638 are not output. C


g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the No. 2 side airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C

50.CHECK NO. 2 SIDE AIRBAG SENSOR RH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 No. 2 Side Airbag Sensor LH
*2 No. 1 Side Airbag Sensor RH


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the No. 2 side airbag sensor RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1632 is output. A
DTC B1637 is output. B
DTCs B1632 and B1637 are not output. C


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the No. 2 side airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C

51.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the No. 2 side airbag sensor RH and door side airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the No. 2 side airbag sensor RH and door side airbag sensor RH. Also disconnect the connectors that link the floor wire and front door wire RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

52.CHECK WIRE HARNESS (OPEN)

NG

REPLACE WIRE HARNESS

52.CHECK WIRE HARNESS (OPEN)
a.
C284683C18
0.792,0.573 1.135,0.813 0.344,0.24 0.542,3.625 0.865,3.854 0.323,0.229 2.333,1.083 1.917,0.667 true 1.01,4.167 1.385,3.75 true 2.042,4.167 1.625,3.75 true 1.354,1.083 1.771,0.667 true 1.844,1.302 1.844,1.094 false 0.552,2.313 0.917,2.625 0.365,0.313 10 false *1 2.74,2.333 3.063,2.75 0.323,0.417 10 false *2 1.781,1.313 2.135,1.615 0.354,0.302 10 false *3 0.635,0.167 0.979,0.583 0.344,0.417 10 false *a 0.344,3.156 0.625,3.583 0.281,0.427 10 false *b 2.396,2.333 2.719,2.75 0.323,0.417 10 false A 2.083,2.333 2.406,2.75 0.323,0.417 10 false B 1.74,2.333 2.063,2.75 0.323,0.417 10 false C 1.583,2.333 1.906,2.75 0.323,0.417 10 false D 1.24,2.323 1.563,2.74 0.323,0.417 10 false E 0.927,2.323 1.25,2.74 0.323,0.417 10 false F 1.188,1.104 1.604,1.521 0.417,0.417 10 false BDR+ 2.229,1.104 2.646,1.521 0.417,0.417 10 false BDR- 1.885,4.167 2.302,4.5 0.417,0.333 10 false BDR+ 0.844,4.167 1.26,4.604 0.417,0.438 10 false BDR- 0.844,0.615 1.26,1.031 0.417,0.417 10 false M57 0.656,3.667 1.073,4.083 0.417,0.417 10 false I5
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor RH)


Connect the connectors that link the floor wire and front door wire RH.


b.

Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-2 (BDR+) - I5-1 (BDR-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

53.CHECK WIRE HARNESS (SHORT)

NG

61.CHECK FLOOR WIRE (OPEN)
53.CHECK WIRE HARNESS (SHORT)
a.
C284684C17
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 true 2.25,2.75 1.792,2.313 true 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDR- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDR+ 0.823,2.229 1.219,2.583 0.396,0.354 10 false I5
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*a Front view of wire harness connector
(to Door Side Airbag Sensor RH)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-2 (BDR+) - I5-1 (BDR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

54.CHECK WIRE HARNESS (SHORT TO B+)

NG

60.CHECK FLOOR WIRE (SHORT)
54.CHECK WIRE HARNESS (SHORT TO B+)
a.
C284684C17
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 true 2.25,2.75 1.792,2.313 true 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDR- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDR+ 0.823,2.229 1.219,2.583 0.396,0.354 10 false I5
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*a Front view of wire harness connector
(to Door Side Airbag Sensor RH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I5-2 (BDR+) - Body ground Ignition switch ON Below 1 V
I5-1 (BDR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

55.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

59.CHECK FLOOR WIRE (SHORT TO B+)
55.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C284684C17
0.698,2.188 1.031,2.427 0.333,0.24 1.167,2.75 1.563,2.313 true 2.25,2.75 1.792,2.313 true 0.563,0.688 0.958,1.01 0.396,0.323 10 false *1 2.729,0.688 3.104,1.073 0.375,0.385 10 false *2 0.5,1.646 0.896,2 0.396,0.354 10 false *a 2.396,0.688 2.771,1.073 0.375,0.385 10 false A 2.094,0.688 2.469,1.073 0.375,0.385 10 false B 1.74,0.688 2.115,1.073 0.375,0.385 10 false C 1.583,0.688 1.958,1.073 0.375,0.385 10 false D 1.24,0.688 1.615,1.073 0.375,0.385 10 false E 0.938,0.688 1.313,1.073 0.375,0.385 10 false F 1.01,2.75 1.417,3.104 0.406,0.354 10 false BDR- 2.125,2.75 2.542,3.115 0.417,0.365 10 false BDR+ 0.823,2.229 1.219,2.583 0.396,0.354 10 false I5
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*a Front view of wire harness connector
(to Door Side Airbag Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-2 (BDR+) - Body ground Always 1 MΩ or higher
I5-1 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

56.CHECK NO. 2 SIDE AIRBAG SENSOR RH

NG

58.CHECK FLOOR WIRE (SHORT TO GROUND)
56.CHECK NO. 2 SIDE AIRBAG SENSOR RH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 No. 2 Side Airbag Sensor LH
*2 No. 1 Side Airbag Sensor RH


Connect the connector to the door side airbag sensor RH.


b.

Interchange the No. 2 side airbag sensor RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B166D or B166E is output. A
DTC B167B or B167C is output. B
DTCs B166D, B166E, B167B and B167C are not output. C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the No. 2 side airbag sensor RH and LH to their original positions and connect the connectors.



A

57.CHECK DOOR SIDE AIRBAG SENSOR RH

B

C

57.CHECK DOOR SIDE AIRBAG SENSOR RH
a.
C238395C02
0.719,1.021 1.51,1.656 0.792,0.635 10 false *1 2.552,1 2.906,1.406 0.354,0.406 10 false *2 2.26,1.021 2.531,1.51 0.271,0.49 10 false A 2.104,1.021 2.531,1.563 0.427,0.542 10 false B 1.76,1.021 2.24,1.583 0.479,0.563 10 false C 1.604,1.021 2.031,1.615 0.427,0.594 10 false D 1.26,1.021 1.708,1.625 0.448,0.604 10 false E 1.115,1.021 1.792,1.771 0.677,0.75 10 false F
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor RH


Interchange the door side airbag sensor RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B166D or B166E is output. A
DTC B167B or B167C is output. B
DTCs B166D, B166E, B167B and B167C are not output. C


g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the door side airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C

58.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C284682C24
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 true 1.406,2.479 1.667,3 true 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.604,1.521 0.917,1.76 0.313,0.24 10 false IM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDR+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDR-
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Front Door Wire RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire RH)


Disconnect the floor wire connector from the front door wire RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IM1-22 (BDR+) - Body ground Always 1 MΩ or higher
IM1-40 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE

59.CHECK FLOOR WIRE (SHORT TO B+)
a.
C284682C24
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 true 1.406,2.479 1.667,3 true 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.604,1.521 0.917,1.76 0.313,0.24 10 false IM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDR+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDR-
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Front Door Wire RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire RH)


Disconnect the floor wire connector from the front door wire RH.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
IM1-22 (BDR+) - Body ground Ignition switch ON Below 1 V
IM1-40 (BDR-) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE

60.CHECK FLOOR WIRE (SHORT)
a.
C284682C24
0.5,1.479 0.917,1.729 0.417,0.25 1.344,0.708 1.344,0.958 false 1.917,0.167 2.083,0.167 2.083,0.167 2.083,0.583 false 1.396,2.333 1.063,2.99 true 1.406,2.479 1.667,3 true 0.365,0.552 0.677,0.781 0.313,0.229 10 false *1 2.927,0.563 3.25,0.823 0.323,0.26 10 false *2 1.281,0.99 1.594,1.26 0.313,0.271 10 false *3 1.771,0.094 2.021,0.427 0.25,0.333 10 false *4 0.146,1.458 0.458,1.698 0.313,0.24 10 false *a 2.583,0.563 2.906,0.823 0.323,0.26 10 false A 2.271,0.563 2.594,0.823 0.323,0.26 10 false B 1.833,0.563 2.156,0.823 0.323,0.26 10 false C 1.521,0.563 1.844,0.823 0.323,0.26 10 false D 1.094,0.563 1.417,0.823 0.323,0.26 10 false E 0.781,0.563 1.104,0.823 0.323,0.26 10 false F 0.604,1.521 0.917,1.76 0.313,0.24 10 false IM1 0.917,3 1.354,3.25 0.438,0.25 10 false BDR+ 1.531,3 2.031,3.25 0.5,0.25 10 false BDR-
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Front Door Wire RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Door Wire RH)


Disconnect the floor wire connector from the front door wire RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IM1-22 (BDR+) - IM1-40 (BDR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE

61.CHECK FLOOR WIRE (OPEN)
a.
C284681C17
0.865,0.563 1.219,0.792 0.354,0.229 0.458,2.823 0.823,3.042 0.365,0.219 1.781,4.302 1.406,3.771 true 1.844,1.344 1.844,1.094 false 1.333,1.167 1.771,0.667 true 2.333,1.167 1.917,0.667 true 1.333,2.229 1.333,2.479 false 1.906,1.771 2.073,1.771 2.073,1.771 2.073,2.104 false 1,4.313 1.406,3.635 true 0.417,2.083 0.813,2.49 0.396,0.406 10 false *1 2.865,2.094 3.26,2.667 0.396,0.573 10 false *2 1.271,2.479 1.604,2.719 0.333,0.24 10 false *3 1.75,1.698 2.146,2.031 0.396,0.333 10 false *4 1.781,1.354 2.198,1.677 0.417,0.323 10 false *5 0.604,0.167 1,0.583 0.396,0.417 10 false *a 0.156,2.833 0.552,3.24 0.396,0.406 10 false *b 2.542,2.083 2.938,2.656 0.396,0.573 10 false A 2.24,2.083 2.635,2.656 0.396,0.573 10 false B 1.813,2.083 2.208,2.656 0.396,0.573 10 false C 1.521,2.083 1.917,2.656 0.396,0.573 10 false D 1.094,2.083 1.49,2.656 0.396,0.573 10 false E 0.792,2.083 1.188,2.656 0.396,0.573 10 false F 1.177,1.167 1.677,1.5 0.5,0.333 10 false BDR+ 2.198,1.167 2.698,1.5 0.5,0.333 10 false BDR- 0.844,4.302 1.344,4.635 0.5,0.333 10 false BDR+ 1.667,4.302 2.167,4.635 0.5,0.333 10 false BDR- 0.927,0.594 1.427,0.927 0.5,0.333 10 false M57 0.542,2.854 1.042,3.188 0.5,0.333 10 false IM1
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH)
*b Front view of wire harness connector
(to Front Door Wire RH)


Disconnect the floor wire connector from the front door wire RH.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IM1-22 (BDR+) - IM1-40 (BDR-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE

62.CHECK NO. 1 SIDE AIRBAG SENSOR RH
a.
C238218C01
0.802,1.188 1.094,1.479 0.292,0.292 10 false *1 1.115,1.167 1.281,1.448 0.167,0.281 10 false D 1.271,1.167 1.458,1.438 0.188,0.271 10 false C 1.719,1.177 1.948,1.5 0.229,0.323 10 false B 1.875,1.177 2.094,1.396 0.219,0.219 10 false A 2.302,0.906 2.625,1.198 0.323,0.292 10 false *2
*1 No. 1 Side Airbag Sensor LH
*2 Airbag Sensor Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the No. 1 side airbag sensor RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1622 is output. A
DTC B1627 is output. B
DTCs B1622 and B1627 are not output. C


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the No. 1 side airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C

63.CHECK NO. 2 SIDE AIRBAG SENSOR RH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 No. 2 Side Airbag Sensor LH
*2 No. 1 Side Airbag Sensor RH


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the No. 2 side airbag sensor RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1632 is output. A
DTC B1637 is output. B
DTCs B1632 and B1637 are not output. C


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the No. 2 side airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C