Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _060061 SUPPLEMENTAL RESTRAINT SYSTEMS _0294202 REAR AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  REAR AIRBAG SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the No. 2 side airbag sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)*2 Stop and start system (Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

*2: w/ Stop and start system

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.

·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B458500

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


CAUTION:
·
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If an SRS part is accidentally deployed, it may cause a serious injury.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE REAR SEAT ASSEMBLY

Hide 67918A 4.REMOVE REAR DOOR SCUFF PLATE

Hide 62332A 5.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

HINT:

Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the rear seat side garnish.


Hide 71304C 6.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY

Hide 62552F 7.REMOVE REAR SEAT SIDE GARNISH

Hide 89831C 8.REMOVE NO. 2 SIDE AIRBAG SENSOR

a.

Check that the ignition switch off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B458403

Remove the bolt and disengage the claw to separate the No. 2 side airbag sensor.


d.

Disconnect the connector to remove the No. 2 side airbag sensor.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

C195226C40
3.927,1.313 3.927,2.146 false 1.385,1.313 1.385,2.146 true 0.948,1.156 0.417,0.729 true 3.469,1.146 2.938,0.74 true 3.625,1.042 3.427,0.667 true 1.125,1.042 0.833,0.604 true 0.667,0.406 0.854,0.583 0.188,0.177 10 false *a 3.313,0.469 3.5,0.646 0.188,0.177 10 false *a 1.313,2.208 1.5,2.385 0.188,0.177 10 false *b 0.969,1.708 1.156,1.885 0.188,0.177 10 false *c 3.531,1.729 3.719,1.906 0.188,0.177 10 false *c 3.823,2.177 4.01,2.354 0.188,0.177 10 false *b 1.427,0.625 1.615,0.802 0.188,0.177 10 false *d 3.875,0.646 4.063,0.823 0.188,0.177 10 false *d 2.719,0.542 2.969,0.729 0.25,0.188 10 false (A) 0.26,0.5 0.51,0.688 0.25,0.188 10 false (A)
*a White Housing Lock *b Yellow CPA
*c Slide *d Push



ii.

Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.




e.

After disconnecting the connector, check that the position of the white housing lock is as shown in the illustration.

B296256C01
5.01,0.51 5.302,0.781 0.292,0.271 10 *b 1.792,0.51 2.083,0.802 0.292,0.292 10 *a
*a Correct *b Incorrect