Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD
RM32H0E _58 Vehicle Interior _060061 SUPPLEMENTAL RESTRAINT SYSTEMS _0294192 STEERING PAD N

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

·
B394910

Never dispose of a horn button assembly with an undeployed airbag.

·

The airbag produces an exploding sound when it is deployed, so perform the operation outdoors where it will not disturb nearby residents.

B436767

·

When deploying the airbag, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical noise.

·

When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the horn button assembly.

·

The horn button assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a horn button assembly with a deployed airbag.

·

Do not apply water, etc. to a horn button assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

When scrapping a vehicle equipped with an SRS or disposing of the horn button assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Department of the distributor.


Hide 45130 2.DISPOSE OF HORN BUTTON ASSEMBLY (When Installed to Vehicle)

NOTICE:
·

When disposing of the horn button assembly, never use the customer's vehicle to deploy the airbag.

·

Be sure to observe the following procedure when deploying the airbag.



HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N08
0.99,1.208 0.792,0.771 0.792,0.771 0.646,0.771 false 0.323,0.688 0.781,0.885 0.458,0.198 10 SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying the airbag, always use the specified SST:

SRS airbag deployment tool


i.
C110372C23
0.5,0.719 0.833,0.719 0.833,0.719 0.833,1.646 false 2.719,0.74 2.521,0.74 false 0.135,0.604 0.448,0.802 0.313,0.198 10 false SST 2.76,0.646 2.979,0.844 0.219,0.198 10 false *a
*a Battery


Connect SST to the battery.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.
C110475N08
1.75,0.635 1.458,0.333 false 1.177,0.198 1.531,0.448 0.354,0.25 10 false SST

Check the function of SST.

Press the SST activation switch and check that the LED of the SST activation switch comes on.

CAUTION:
·

Do not connect the yellow SST connector to the airbag.

·

If the LED comes on when the activation switch is not being pressed, SST is malfunctioning. Replace SST.




iii.

Disconnect SST from the battery.




c.

Remove the lower steering column cover sub-assembly.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>REMOVAL


d.

Disconnect the airbag connector from the spiral cable with sensor sub-assembly.

i.
B454024C01
1.063,2.438 1.396,2.438 true 1.438,2.333 1.583,2.5 0.146,0.167 10 true *a
*a Slider


Slide the slider to release the lock, and then disconnect the airbag connector from the spiral cable with sensor sub-assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.




e.

Install SST.

CAUTION:
B394903

Check that there is no looseness in the steering wheel assembly or horn button assembly.


i.
B454025N01
1.469,2 2.438,2 2.438,2 2.438,1.583 true 2.083,2 2.083,1.583 true 1.125,1.906 1.458,2.073 0.333,0.167 10 true SST

After connecting the following SST to each other, connect them to the spiral cable with sensor sub-assembly.

SST
09082-00700  
09082-00780  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.



ii.
C154370C17
1.76,0.552 1.99,0.25 1.99,0.25 2.188,0.25 false 0.458,1.167 0.677,1.167 false 0.677,1.167 0.927,1.396 false 2.229,0.167 2.542,0.323 0.313,0.156 10 false *a 1.594,1.802 1.906,1.958 0.313,0.156 10 false *b 0.177,1.104 0.573,1.323 0.396,0.219 10 false SST
*a Battery
*b 10 m (32.8 ft.) or more


Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.


iii.

Maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

NOTICE:

Take care not to damage the SST wire harness.



iv.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.



f.

Deploy the airbag.

i.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Press the SST activation switch to deploy the airbag.

CAUTION:
·
B400936

Before deployment, make sure that no one is inside or near the vehicle.

·
B394905

The horn button assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·
B394908

Use gloves and safety glasses when handling a horn button assembly with a deployed airbag.

·
B394906

Do not apply water, etc. to a horn button assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




Hide 45130 3.DISPOSE OF HORN BUTTON ASSEMBLY (When not Installed to Vehicle)

NOTICE:

Be sure to observe the following procedure when deploying the airbag.


HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N08
0.99,1.208 0.792,0.771 0.792,0.771 0.646,0.771 false 0.323,0.688 0.781,0.885 0.458,0.198 10 SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying the airbag, always use the specified SST:

SRS airbag deployment tool


i.
C110372C23
0.5,0.719 0.833,0.719 0.833,0.719 0.833,1.646 false 2.719,0.74 2.521,0.74 false 0.135,0.604 0.448,0.802 0.313,0.198 10 false SST 2.76,0.646 2.979,0.844 0.219,0.198 10 false *a
*a Battery


Connect SST to the battery.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.
C110475N08
1.75,0.635 1.458,0.333 false 1.177,0.198 1.531,0.448 0.354,0.25 10 false SST

Check the function of SST.

Press the SST activation switch and check that the LED of the SST activation switch comes on.

CAUTION:
·

Do not connect the yellow SST connector to the airbag.

·

If the LED comes on when the activation switch is not being pressed, SST is malfunctioning. Replace SST.




iii.

Disconnect SST from the battery.



b.

Remove the horn button assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>REMOVAL

CAUTION:
·
B422343

Before removing the horn button assembly, wait at least 90 seconds after turning the ignition switch off and disconnecting the cable from the negative (-) battery terminal.

·
B454012C01
0,0 0,0 false
V100155

Deployment Side


When storing the horn button assembly, keep the airbag deployment side facing upward.




c.
B104882C16
2.313,0.938 2.052,0.427 2.052,0.427 1.875,0.427 false 2.656,1.469 2.896,1.646 0.24,0.177 10 *a 1.635,0.333 1.844,0.521 0.208,0.188 10 *b
*a Wire Diameter
*b Stripped Wire Cross Sectional Area


Using braided wire, tie down the horn button assembly to an unneeded tire and wheel set.

Wire:

Stripped wire cross sectional area

1.25 mm2 (0.0019 in.2) or more


CAUTION:

If the wire is too thin or an alternative object is used to tie down the horn button assembly, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross sectional area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the cross sectional area of the stripped wire:

Cross sectional area = 3.14 x (Diameter)2 / 4


i.
B454026N01
1.906,2.01 2.323,1.594 false 2.396,1.49 2.854,1.688 0.458,0.198 10 false SST

Connect SST to the horn button assembly (for Single Type).

SST
09082-00830  


ii.
B454027C01
0.615,1.75 1.031,1.333 true 2.396,1.333 2.813,1.75 true 1.75,3.865 2.167,4.281 true 2.333,1.052 2.75,0.635 true 0.667,0.625 1.083,1.042 true 2.24,4.177 2.552,4.333 0.313,0.156 10 false *a 0.458,0.521 0.771,0.677 0.313,0.156 10 false *b 2.885,1.646 3.198,1.802 0.313,0.156 10 false *a 0.417,1.646 0.729,1.802 0.313,0.156 10 false *a 2.823,0.531 3.135,0.688 0.313,0.156 10 false *b
*a 2 times or more
*b Omega Spring


Wind 2 wires around the omega springs at least 2 times each (for Single Type).

CAUTION:

Tightly wind the wires around the omega springs without any slack.



iii.
B454028N01
1.927,2.01 2.344,1.594 false 2.396,1.49 2.854,1.688 0.458,0.198 10 false SST

Connect SST to the horn button assembly (for Dual Type).

SST
09082-00840  


iv.
B454029C01
0.604,1.74 1.021,1.323 true 2.802,1.74 2.385,1.323 true 2.167,4.281 1.75,3.865 true 2.333,1.021 2.75,0.604 true 1.083,1.021 0.667,0.604 true 2.198,4.198 2.51,4.354 0.313,0.156 10 false *a 0.406,1.635 0.719,1.792 0.313,0.156 10 false *a 2.875,1.635 3.188,1.792 0.313,0.156 10 false *a 0.458,0.5 0.771,0.656 0.313,0.156 10 false *b 2.823,0.5 3.135,0.656 0.313,0.156 10 false *b
*a 2 times or more
*b Omega Spring


Wind 2 wires around the omega springs at least 2 times each (for Dual Type).

CAUTION:

Tightly wind the wires around the omega springs without any slack.



v.
B454030C01
1.781,1.927 2.094,2.083 0.313,0.156 10 false *a 0.073,0.906 0.385,1.063 0.313,0.156 10 false *b
*a Inner Diameter
*b Width


Face the airbag deployment side of the horn button assembly upward on top of an unneeded tire and wheel set. Separately tie each side of the horn button assembly to the wheel through the hub nut holes. Position the SST connector so that it hangs downward through the hub hole of the wheel.

Minimum tire size:
Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


CAUTION:
·

Make sure that the wires are tight. If there is slack in the wires, the horn button assembly may break loose when the airbag is deployed.

·
B454031C01
0,0 0,0 false
V100155

Deployment Side


Always tie down the horn button assembly with the airbag deployment side facing upward.



NOTICE:

The wheel and tire may be damaged by the airbag deployment, so use an unneeded tire and wheel set.




d.
B454032N01
2.854,0.5 3.271,0.917 false 2.5,0.396 2.958,0.594 0.458,0.198 10 false SST

Install SST.

CAUTION:

Place the tire and wheel set on level ground.


i.

Connect the SST connector.

SST
09082-00700  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the wheel.



ii.
B454033C01
0.552,1 0.885,1 false 1.25,1.802 1.563,1.958 0.313,0.156 10 false *a 0.958,0.896 1.417,1.094 0.458,0.198 10 false SST
*a 10 m (32.8 ft.) or more


Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire and wheel set.



e.

Cover the horn button assembly (using a cardboard box).

i.
B454034C01
0.406,1.667 0.906,1.667 true 2.427,1.667 2.896,1.667 true 0.208,1.573 0.521,1.729 0.313,0.156 10 false *a 0.948,0.729 1.26,0.885 0.313,0.156 10 false Y 2.844,0.896 3.156,1.052 0.313,0.156 10 false X 1.156,0.125 1.469,0.281 0.313,0.156 10 false Y 2.969,1.573 3.281,1.729 0.313,0.156 10 false *a
*a Weight


Cover the horn button assembly with a cardboard box.


ii.

Place weights on the cardboard box in 4 places totaling at least 190 N (19 kg, 42.7 lb).

Minimum cardboard box size:
X:

460 mm (1.51 ft.)

Y:

650 mm (2.13 ft.)


NOTICE:
·

When dimension Y of the cardboard box exceeds the diameter of the wheel and tire to which the horn button assembly is tied, X should be the following size.

X = 460 mm (1.51 ft.) + width of tire

·

If a cardboard box smaller than the specified size is used, it may be broken by the shock of the airbag deployment.





f.

Cover the horn button assembly (using tires).

i.
B454035C01
0.667,1.823 0.979,1.979 0.313,0.156 10 false *a 1.667,0.438 1.979,0.594 0.313,0.156 10 false *b 2.583,0.927 2.896,1.083 0.313,0.156 10 false *c
*a Tires (3 or more)
*b Inner Diameter
*c Width


Place at least 3 tires without wheels onto the tire and wheel set to which the horn button assembly is tied.


ii.

Place a tire and wheel set on top.

Minimum tire size:
Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


CAUTION:

Do not use tires with wheels except on the top and bottom.


NOTICE:
·

The wheels and tires may be damaged by the airbag deployment, so use unneeded wheels and tires.

·

Do not place the SST connector under the tire because it could be damaged.




iii.
C223306

Tie the tires together with 2 wires.

CAUTION:

Make sure that the wires are tight. Looseness in the wires will result in the tires breaking loose when the airbag is deployed.




g.

Deploy the airbag.

i.
B454036C01
2.333,3.375 3,3.375 true 2.438,1.25 3.021,1.25 true 1.333,1.271 1.333,1.438 false 1.333,3.51 1.333,3.677 false 0.417,1.25 0.719,1.25 false 0.417,3.5 0.719,3.5 false 3.094,1.146 3.406,1.302 0.313,0.156 10 false *1 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 0.083,2.167 0.396,2.323 0.313,0.156 10 false *b 1.26,1.438 1.573,1.594 0.313,0.156 10 false *c 1.229,1.885 1.542,2.042 0.313,0.156 10 false *d 3.073,3.281 3.385,3.438 0.313,0.156 10 false *1 1.26,3.667 1.573,3.823 0.313,0.156 10 false *c 1.219,4.125 1.531,4.281 0.313,0.156 10 false *d 0.083,1.156 0.542,1.354 0.458,0.198 10 false SST 0.083,3.406 0.542,3.604 0.458,0.198 10 false SST
*1 Horn Button Assembly
*a Using a Cardboard Box
*b Using Tires
*c Battery
*d 10 m (32.8 ft.) or more


Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.

Check that no one is within a 10 m (32.8 ft.) radius of the wheel to which the horn button assembly is tied.


iii.

Press the SST activation switch to deploy the airbag.

CAUTION:
B400935

Before deployment, make sure that no one is near the airbag.


HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




h.

Dispose of the horn button assembly.

CAUTION:
·
B396586

The horn button assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·
B394909

Use gloves and safety glasses when handling a horn button assembly with a deployed airbag.

·
B394907

Do not apply water, etc. to a horn button assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



i.

Remove the horn button assembly from the tire and wheel set.


ii.

Place the horn button assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.