Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _060136 METER / GAUGE / DISPLAY _0294876 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1507  Open in Turn Signal Circuit  B1508  Short in Turn Signal / Hazard Flasher Circuit  


DESCRIPTION

These DTCs are stored when the combination meter assembly detects an open in a turn signal light circuit, or a short in a turn signal light circuit or the hazard warning light circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1507 Open in Turn Signal Circuit When IG voltage is 9.5 V or more and the following condition is detected:
·

Open in turn signal light circuit


·

LED

·

Bulb*1

·

Harness or connector

·

Headlight ECU sub-assembly LH

·

Headlight ECU sub-assembly RH

·

Combination meter assembly


DTC stored -
B1508 Short in Turn Signal / Hazard Flasher Circuit When IG voltage is 9.5 V or more and the following condition is detected:
·

Short in turn signal light circuit or hazard warning light circuit


·

LED

·

Bulb*1

·

Harness or connector

·

Headlight ECU sub-assembly LH

·

Headlight ECU sub-assembly RH

·

Combination meter assembly


DTC stored -

*1: for Halogen Headlight Type


WIRING DIAGRAM

C360593E03
0.083,0.083 1.958,0.365 1.875,0.281 12 false for LED Headlight Type: 0.25,1.198 2.104,1.583 1.854,0.385 10 false Headlight Assembly LH (Front Turn Signal Light LH) 2.271,0.333 2.427,0.531 0.156,0.198 10 false 9 2.26,0.51 2.417,0.708 0.156,0.198 10 false C 2.219,0.708 2.531,0.906 0.313,0.198 10 false 13 2.26,0.896 2.417,1.094 0.156,0.198 10 false C 2.552,0.417 3.323,0.615 0.771,0.198 10 false TURN+ 2.552,0.802 3.323,1 0.771,0.198 10 false TURN- 3.708,0.417 4.167,0.615 0.458,0.198 10 false TNS 3.677,0.802 4.135,1 0.458,0.198 10 false GND 4.094,0.51 4.552,0.708 0.458,0.198 10 false A16 4.094,0.896 4.552,1.094 0.458,0.198 10 false A16 4.135,0.323 4.448,0.521 0.313,0.198 10 false 11 4.135,0.708 4.448,0.906 0.313,0.198 10 false 12 2.396,1.198 4.219,1.594 1.823,0.396 10 false Headlight ECU sub-assembly LH 1.875,3.146 2.552,3.333 0.677,0.188 10 false 2*1, 12*2 2.552,3.156 3.25,3.344 0.698,0.188 10 false E*1, -*2 2.542,1.875 3.208,2.073 0.667,0.198 10 false E*1, -*2 1.896,1.865 2.573,2.083 0.677,0.219 10 false 2*1, 12*2 3.896,1.865 4.052,2.063 0.156,0.198 10 false B 4.073,1.865 4.813,2.063 0.74,0.198 10 false 1*1, 16*2 4.917,1.865 5.229,2.063 0.313,0.198 10 false 13 5.188,1.865 5.5,2.063 0.313,0.198 10 false LL 5.188,3.146 5.5,3.344 0.313,0.198 10 false LR 4.99,3.146 5.146,3.344 0.156,0.198 10 false 7 5.427,3.615 5.99,3.958 0.563,0.344 10 false Flasher Relay IC 6.323,5.354 6.781,5.552 0.458,0.198 10 false CPU 5.573,5.74 6.135,6.083 0.563,0.344 10 false Flasher Relay IC 3.896,3.146 4.052,3.344 0.156,0.198 10 false B 4.094,3.135 4.833,3.333 0.74,0.198 10 false 1*1, 16*2 2.188,2.25 3.25,2.479 1.063,0.229 10 false J7*1, J11*2 2.167,2.417 4.521,2.625 2.354,0.208 10 false Outer Rear View Mirror Assembly LH 2.188,3.521 3.167,3.708 0.979,0.188 10 false I8*1, I7*2 2.167,3.667 4.542,3.865 2.375,0.198 10 false Outer Rear View Mirror Assembly RH 5.167,5.708 5.781,5.906 0.615,0.198 10 false TRNL 4.99,5.708 5.146,5.906 0.156,0.198 10 false 6 5.167,6.99 5.781,7.188 0.615,0.198 10 false TRNR 4.99,6.99 5.146,7.188 0.156,0.198 10 false 5 5.167,8.135 5.479,8.333 0.313,0.198 10 false F5 5.156,8.302 7.031,8.521 1.875,0.219 10 false Combination Meter Assembly 0.25,5.042 2.125,5.417 1.875,0.375 10 false Headlight Assembly RH (Front Turn Signal Light RH) 2.396,5.042 4.208,5.385 1.813,0.344 10 false Headlight ECU sub-assembly RH 2.271,4.365 2.427,4.563 0.156,0.198 10 false B 2.271,4.75 2.427,4.948 0.156,0.198 10 false B 2.271,4.177 2.427,4.375 0.156,0.198 10 false 9 2.229,4.563 2.542,4.76 0.313,0.198 10 false 13 2.563,4.271 3.333,4.469 0.771,0.198 10 false TURN+ 2.563,4.656 3.333,4.854 0.771,0.198 10 false TURN- 3.708,4.271 4.167,4.469 0.458,0.198 10 false TNS 3.688,4.656 4.146,4.854 0.458,0.198 10 false GND 4.094,4.354 4.552,4.552 0.458,0.198 10 false A17 4.094,4.74 4.552,4.938 0.458,0.198 10 false A17 4.125,4.177 4.438,4.375 0.313,0.198 10 false 11 4.125,4.563 4.438,4.76 0.313,0.198 10 false 12 2.552,5.719 2.708,5.917 0.156,0.198 10 false E 2.354,5.719 2.51,5.917 0.156,0.198 10 false 3 3.698,5.719 4.156,5.917 0.458,0.198 10 false TRN 4.104,5.719 4.26,5.917 0.156,0.198 10 false 4 2.354,7 2.51,7.198 0.156,0.198 10 false 3 2.552,7 2.708,7.198 0.156,0.198 10 false E 3.698,7 4.156,7.198 0.458,0.198 10 false TRN 4.104,7 4.26,7.198 0.156,0.198 10 false 4 2.177,6.208 4.594,6.417 2.417,0.208 10 false Rear Combination Light Assembly LH 2.177,6.052 2.635,6.25 0.458,0.198 10 false M48 2.177,7.49 4.594,7.698 2.417,0.208 10 false Rear Combination Light Assembly RH 2.177,7.333 2.635,7.531 0.458,0.198 10 false M47 0.385,8.115 2.802,8.323 2.417,0.208 10 false *1: for TMC Made 0.385,8.448 2.802,8.656 2.417,0.208 10 false *2: for TMMT Made

C360594E03
0.083,0.083 2.208,0.333 2.125,0.25 12 false for Halogen Headlight Type: 2.354,0.604 2.51,0.802 0.156,0.198 10 false 6 2.552,0.604 2.708,0.802 0.156,0.198 10 false E 2.354,0.99 2.813,1.188 0.458,0.198 10 false A11 2.344,1.146 4.198,1.51 1.854,0.365 10 false Headlight Assembly LH (Front Turn Signal Light LH) 3.896,0.604 4.052,0.802 0.156,0.198 10 false B 4.115,0.604 4.271,0.802 0.156,0.198 10 false 4 2.542,1.865 3.271,2.083 0.729,0.219 10 false E*1, -*2 1.865,1.854 2.615,2.021 0.75,0.167 10 false 2*1, 12*2 3.896,1.854 4.052,2.052 0.156,0.198 10 false B 4.063,1.854 4.76,2.073 0.698,0.219 10 false 1*1, 16*2 2.281,2.24 3.333,2.427 1.052,0.188 10 false J7*1, J11*2 2.26,2.406 4.323,2.75 2.063,0.344 10 false Outer Rear View Mirror Assembly LH 4.927,1.854 5.24,2.052 0.313,0.198 10 false 13 5.188,1.854 5.5,2.052 0.313,0.198 10 false LL 4.99,3.104 5.146,3.302 0.156,0.198 10 false 7 5.188,3.104 5.5,3.302 0.313,0.198 10 false LR 5.438,3.427 6,3.781 0.563,0.354 10 false Flasher Relay IC 5.573,5.594 6.135,5.948 0.563,0.354 10 false Flasher Relay IC 6.323,5.25 6.781,5.448 0.458,0.198 10 false CPU 5.156,5.615 5.771,5.813 0.615,0.198 10 false TRNL 5.156,6.865 5.771,7.063 0.615,0.198 10 false TRNR 4.979,5.615 5.135,5.813 0.156,0.198 10 false 6 4.979,6.865 5.135,7.063 0.156,0.198 10 false 5 5.156,8.292 7.01,8.51 1.854,0.219 10 false Combination Meter Assembly 5.167,8.125 5.479,8.323 0.313,0.198 10 false F5 2.542,3.115 3.198,3.281 0.656,0.167 10 false E*1, -*2 1.885,3.104 2.542,3.313 0.656,0.208 10 false 2*1, 12*2 3.896,3.115 4.052,3.313 0.156,0.198 10 false B 4.063,3.115 4.76,3.323 0.698,0.208 10 false 1*1, 16*2 2.26,3.656 4.323,4 2.063,0.344 10 false Outer Rear View Mirror Assembly RH 2.271,3.49 3.156,3.698 0.885,0.208 10 false I8*1, I7*2 2.552,4.365 2.708,4.563 0.156,0.198 10 false E 2.354,4.365 2.51,4.563 0.156,0.198 10 false 6 3.896,4.365 4.052,4.563 0.156,0.198 10 false B 4.115,4.365 4.271,4.563 0.156,0.198 10 false 4 2.333,4.906 4.219,5.271 1.885,0.365 10 false Headlight Assembly RH (Front Turn Signal Light RH) 2.344,4.75 2.802,4.948 0.458,0.198 10 false A29 2.552,5.625 2.708,5.823 0.156,0.198 10 false E 2.354,5.625 2.51,5.823 0.156,0.198 10 false 3 3.719,5.625 4.177,5.823 0.458,0.198 10 false TRN 4.104,5.625 4.26,5.823 0.156,0.198 10 false 4 2.25,6 2.708,6.198 0.458,0.198 10 false M48 2.25,6.167 4.333,6.51 2.083,0.344 10 false Rear Combination Light Assembly LH 2.354,6.875 2.51,7.073 0.156,0.198 10 false 3 2.552,6.875 2.708,7.073 0.156,0.198 10 false E 3.719,6.875 4.177,7.073 0.458,0.198 10 false TRN 4.104,6.875 4.26,7.073 0.156,0.198 10 false 4 2.25,7.26 2.708,7.458 0.458,0.198 10 false M47 2.25,7.427 4.333,7.771 2.083,0.344 10 false Rear Combination Light Assembly RH 0.375,8 2.458,8.344 2.083,0.344 10 false *1: for TMC Made 0.365,8.375 2.448,8.719 2.083,0.344 10 false *2: for TMMT Made

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the LEDs and bulbs for this system before performing the following procedure.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
RH side turn signal light does not illuminate. A
LH side turn signal light does not illuminate. B



A

2.CHECK TURN SIGNAL LIGHTS (RH SIDE)

B

8.CHECK TURN SIGNAL LIGHTS (LH SIDE)
2.CHECK TURN SIGNAL LIGHTS (RH SIDE)
a.

Turn the ignition switch ON.


b.

Set the headlight dimmer switch assembly to the right turn switch position.


c.

Check the operation of the turn signal lights (RH side).


Result:
Result Proceed to
Front turn signal light assembly (RH side) does not blink. (for LED Headlight Type) A
Front turn signal light assembly (RH side) does not blink. (for Halogen Headlight Type) B
Side turn signal light assembly (RH side) does not blink. C
Rear turn signal light assembly (RH side) does not blink. D



A

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - COMBINATION METER ASSEMBLY OR BODY GROUND)

B

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY OR BODY GROUND)

C

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - OUTER REAR VIEW MIRROR ASSEMBLY RH)

D

7.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY OR BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - COMBINATION METER ASSEMBLY OR BODY GROUND)
a.

Disconnect the A17 headlight ECU sub-assembly RH connector.


b.

Disconnect the F5 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A17-11 (TNS) - F5-7 (LR) Always Below 1 Ω
A17-12 (GND) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A17-11 (TNS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT HEADLIGHT ECU SUB-ASSEMBLY RH
a.

Remove the Headlight ECU sub-assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL


b.
E325512C10
1.458,0.615 1.958,0.865 0.5,0.25 1.469,2.583 1.969,2.833 0.5,0.25 0.76,1.385 0.375,1.948 true 2.677,1.49 2.854,2 true 1.146,3.531 0.573,4.073 true 2.073,3.708 2.406,4.125 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.583,0.656 1.948,0.865 0.365,0.208 10 false A17 1.677,2.625 2.042,2.833 0.365,0.208 10 false B 0.24,1.979 0.698,2.198 0.458,0.219 10 false TNS 2.698,1.99 3.156,2.208 0.458,0.219 10 false GND 0.396,4.104 0.938,4.323 0.542,0.219 10 false TURN+ 2.229,4.156 2.771,4.375 0.542,0.219 10 false TURN-
*a Component without harness connected
(Headlight ECU sub-assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-11 (TNS) - B-9 (TURN+) Always Below 1 Ω
A17-12 (GND) - B-13 (TURN-) Always Below 1 Ω
A17-11 (TNS) - A17-12 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY OR BODY GROUND)
a.

Disconnect the A29 headlight assembly RH connector.


b.

Disconnect the F5 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A29-4 (B) - F5-7 (LR) Always Below 1 Ω
A29-6 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A29-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - OUTER REAR VIEW MIRROR ASSEMBLY RH)
a.

Disconnect the F5 combination meter assembly connector.


b.

Disconnect the I8*1 or I7*2 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F5-7 (LR) - I8-1 (B)*1 Always Below 1 Ω
F5-7 (LR) - I7-16 (B)*2 Always Below 1 Ω
I8-2 (E) - Body ground*1 Always Below 1 Ω
I7-12 (-) - Body ground*2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
I8-1 (B) - Body ground*1 Always 10 kΩ or higher
I7-16 (B) - Body ground*2 Always 10 kΩ or higher


*1: for TMC Made

*2: for TMMT Made



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY OR BODY GROUND)
a.

Disconnect the M47 rear combination light assembly RH connector.


b.

Disconnect the F5 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
M47-4 (TRN) - F5-5 (TRNR) Always Below 1 Ω
M47-3 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
M47-4 (TRN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK TURN SIGNAL LIGHTS (LH SIDE)
a.

Turn the ignition switch ON.


b.

Set the headlight dimmer switch assembly to the left turn switch position.


c.

Check the operation of the turn signal lights (LH side).


Result:
Result Proceed to
Front turn signal light assembly (LH side) does not blink. (for LED Headlight Type) A
Front turn signal light assembly (RH side) does not blink. (for Halogen Headlight Type) B
Side turn signal light assembly (LH side) does not blink. C
Rear turn signal light assembly (LH side) does not blink. D



A

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY LH OR BODY GROUND)

B

11.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY OR BODY GROUND)

C

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - OUTER REAR VIEW MIRROR ASSEMBLY LH OR BODY GROUND)

D

13.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY OR BODY GROUND)
9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY LH OR BODY GROUND)
a.

Disconnect the A16 headlight ECU sub-assembly LH connector.


b.

Disconnect the F5 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A16-11 (TNS) - F5-13 (LL) Always Below 1 Ω
A16-12 (GND) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A16-11 (TNS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT HEADLIGHT ECU SUB-ASSEMBLY LH
a.

Remove the Headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL


b.
E325512C11
1.458,0.615 1.958,0.865 0.5,0.25 1.469,2.583 1.969,2.833 0.5,0.25 0.76,1.385 0.375,1.948 true 2.677,1.49 2.854,2 true 1.146,3.531 0.573,4.073 true 2.073,3.708 2.406,4.125 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.583,0.656 1.948,0.865 0.365,0.208 10 false A16 1.677,2.625 2.042,2.833 0.365,0.208 10 false C 0.24,1.979 0.698,2.198 0.458,0.219 10 false TNS 2.698,1.99 3.156,2.208 0.458,0.219 10 false GND 0.396,4.104 0.938,4.323 0.542,0.219 10 false TURN+ 2.229,4.156 2.771,4.375 0.542,0.219 10 false TURN-
*a Component without harness connected
(Headlight ECU sub-assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A16-11 (TNS) - C-9 (TURN+) Always Below 1 Ω
A16-12 (GND) - C-13 (TURN-) Always Below 1 Ω
A16-11 (TNS) - A16-12 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY OR BODY GROUND)
a.

Disconnect the A11 headlight assembly LH connector.


b.

Disconnect the F5 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A11-4 (B) - F5-13 (LL) Always Below 1 Ω
A11-6 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A11-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - OUTER REAR VIEW MIRROR ASSEMBLY LH OR BODY GROUND)
a.

Disconnect the F5 combination meter assembly connector.


b.

Disconnect the J7*1 or J11*2 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
J7-1 (B) - F5-13 (LL)*1 Always Below 1 Ω
J11-16 (B) - F5-13 (LL)*2 Always Below 1 Ω
J7-2 (E) - Body ground*1 Always Below 1 Ω
J11-12 - Body ground*2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
J7-1 (B) - Body ground*1 Always 10 kΩ or higher
J11-16 (B) - Body ground*2 Always 10 kΩ or higher


*1: for TMC Made

*2: for TMMT Made



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY OR BODY GROUND)
a.

Disconnect the M48 rear combination light assembly LH connector.


b.

Disconnect the F5 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F5-6 (TRNL) - M48-4 (TRN) Always Below 1 Ω
M48-3 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
M48-4 (TRN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR