Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for TMMT Made)
RM32H0E _52 Drivetrain _060137 DRIVE SHAFT / PROPELLER SHAFT _0294912 FRONT DRIVE SHAFT ASSEMBLY(for TMMT Made) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for TMMT Made)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL FRONT DRIVE SHAFT BEARING (for AWD)

a.
C092032E16
2.26,1.615 2.26,0.969 false 2.271,0.969 2.5,0.969 false 0.656,0.333 1.063,0.333 1.063,0.333 1.063,0.646 false 2.563,0.885 3.125,1.094 0.563,0.208 10 false SST 0.302,0.25 0.646,0.438 0.344,0.188 10 false SST

Using SST, install a new front drive shaft bearing.

SST
09527-10011  
09527-30010  

NOTICE:

The front drive shaft bearing should be completely installed.



b.
C092033

Using a snap ring expander, install a new shaft snap ring.


Hide 41336E 2.INSTALL FRONT DRIVE SHAFT DUST COVER LH

a.
C235587C07
0.635,0.323 0.948,0.604 false 0.448,1.063 0.74,1.313 false 0.469,0.208 0.781,0.365 0.313,0.156 10 false *a 0.135,0.948 0.594,1.146 0.458,0.198 10 false SST
*a Steel Plate


Using a steel plate and a press, install a new front drive shaft dust cover LH.

SST
09527-10011  

NOTICE:
·

Press fit the drive shaft dust cover until it reaches the edge of the front drive inboard joint assembly installation area.

·

The dust cover should be completely installed.

·

Be careful not to damage the front drive shaft dust cover LH.

·

Install the front drive shaft dust cover LH in the correct direction.




Hide 41336D 3.INSTALL FRONT DRIVE SHAFT DUST COVER RH

a.

for 8NR-FTS, 2WD:

i.

Perform the same procedure as for the LH side.



b.

for 8NR-FTS, AWD:

i.
C310866E02
1.635,0.302 1.792,0.302 false 1.802,0.219 2.104,0.375 0.302,0.156 10 false SST 2.844,1.313 3.063,1.51 0.219,0.198 10 false (A)

Using SST and a press, install a new front drive shaft dust cover RH until the distance (A) from the tip of the center drive shaft to the front drive shaft dust cover RH meets the specification.

SST
09527-10011  

Distance (A):

274.4 to 275.4 mm (10.80 to 10.84 in.)


NOTICE:
·

The front drive shaft dust cover RH should be completely installed.

·

Be careful not to damage the front drive shaft dust cover RH.

·

Install the front drive shaft dust cover RH in the correct direction.





c.

for 3ZR-FAE:

i.
C360104E01
0.583,0.458 0.583,0.792 false 0.438,0.823 0.917,1.167 0.479,0.344 10 false SST 2.865,1.323 3.229,1.583 0.365,0.26 10 false (A)

Using SST and a press, install a new front drive shaft dust cover RH until the distance (A) from the tip of the center drive shaft to the front drive shaft dust cover RH meets the specification.

SST
09527-10011  

Distance (A):

91.0 to 92.0 mm (3.59 to 3.62 in.)


NOTICE:
·

The front drive shaft dust cover RH should be completely installed.

·

Be careful not to damage the front drive shaft dust cover RH.

·

Install the front drive shaft dust cover RH in the correct direction.





Hide 4.INSTALL FRONT AXLE OUTBOARD JOINT BOOT

a.
C177228C09
2.01,0.885 2.427,1.156 false 2.49,1.083 2.802,1.24 0.313,0.156 10 false *a
*a Protective Tape


Wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


b.
C274280C01
1.115,1.719 1.115,1.427 false 1.656,1.74 1.656,1.479 false 2.344,1.74 2.344,1.438 false 2.979,1.75 2.979,1.229 false 1.063,1.781 1.375,1.938 0.313,0.156 10 *1 1.604,1.792 1.917,1.948 0.313,0.156 10 *2 2.281,1.781 2.594,1.938 0.313,0.156 10 *3 2.948,1.792 3.26,1.948 0.313,0.156 10 *4
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front No. 2 Axle Outboard Joint Boot Clamp
*3 Front Axle Outboard Joint Boot
*4 Front Axle Outboard Joint Boot Clamp
V100135

Outboard joint side
V100136

Inboard joint side


Install new parts onto the front drive outboard joint shaft assembly in the following order:

i.

Front No. 2 axle outboard joint boot clamp


ii.

Front axle outboard joint boot


iii.

Front axle outboard joint boot clamp



c.

Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.

Standard grease capacity:

80 to 100 g (2.83 to 3.52 oz.)



d.

Install the front axle outboard joint boot into the front drive outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the outboard joint boot.

·

Keep the inside of the outboard joint boot free of foreign matter.




Hide 43447F 5.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the front No. 2 axle outboard joint boot clamp onto the front axle outboard joint boot.


c.
C282247C01
2.156,1 2.531,0.76 false 2.563,0.667 3.021,0.865 0.458,0.198 10 false SST 1.677,0.021 1.99,0.177 0.313,0.156 10 false *a 2.552,1.573 2.865,1.729 0.313,0.156 10 false *b
*a Hold
*b Turn


Place SST onto the front No. 2 axle outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


d.

Tighten SST so that the front No. 2 axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.

Remove SST.


f.
C282248E01
1.625,1.063 0.938,1.406 true 0.656,1.323 1.115,1.521 0.458,0.198 10 false SST

Using SST, measure the clearance of the front No. 2 axle outboard joint boot clamp.

SST
09240-00020  

Clearance:

1.2 to 4.0 mm (0.05 to 0.16 in.)


If the clearance is outside the specified range, retighten SST.


Hide 43447E 6.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

a.

Install the front axle outboard joint boot clamp onto the front axle outboard joint boot.


b.
C282249C01
2.219,1.281 2.76,1.073 false 2.802,0.979 3.26,1.177 0.458,0.198 10 false SST 1.781,0.042 2.094,0.198 0.313,0.156 10 false *a 2.49,1.792 2.802,1.948 0.313,0.156 10 false *b
*a Hold
*b Turn


Place SST onto the front axle outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


c.

Tighten SST so that the front axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



d.

Remove SST.


e.
C282250E01
1.542,1.531 2.177,1.656 true 2.229,1.583 2.688,1.781 0.458,0.198 10 false SST

Using SST, measure the clearance of the front axle outboard joint boot clamp.

SST
09240-00020  

Clearance:

1.2 to 4.0 mm (0.05 to 0.16 in.)


If the clearance is outside the specified range, retighten SST.


Hide 43474E 7.INSTALL FRONT DRIVE SHAFT DAMPER LH

a.
C360105C01
0.219,1.625 0.219,1.292 false 0.75,1.719 0.75,1.385 false 1.333,1.625 1.333,1.292 false 2.271,1.813 2.271,1.479 false 2.188,1.865 2.5,2.021 0.313,0.156 10 false *1 0.677,1.771 0.99,1.927 0.313,0.156 10 false *2 0.146,1.667 0.458,1.823 0.313,0.156 10 false *3 1.25,1.677 1.563,1.833 0.313,0.156 10 false *3 1.708,0.563 2,0.771 0.292,0.208 10 false (A)
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front Drive Shaft Damper RH
*3 Front Drive Shaft Damper Clamp


Install parts to the front drive outboard joint shaft assembly in the following order as shown in the illustration.

i.

New front drive shaft damper clamp


ii.

Front drive shaft damper LH


iii.

New front drive shaft damper clamp



b.

Set the dimension (A) as specified below.

Dimension (A):
for 8NR-FTS:

184 to 188 mm (7.25 to 7.40 in.)

for 3ZR-FAE:

229 to 233 mm (9.02 to 9.17 in.)



c.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



d.

Install the 2 front drive shaft damper clamps to the front drive shaft damper LH.

NOTICE:

Be sure to install the clamp in the correct position.



e.
C304762

Using needle-nose pliers, engage the 2 claws to install the 2 front drive shaft damper clamps as shown in the illustration.


Hide 43474D 8.INSTALL FRONT DRIVE SHAFT DAMPER RH

a.
C360105C03
0.219,1.625 0.219,1.292 false 0.75,1.719 0.75,1.385 false 1.333,1.625 1.333,1.292 false 2.271,1.813 2.271,1.479 false 2.188,1.865 2.5,2.021 0.313,0.156 10 false *1 0.677,1.771 0.99,1.927 0.313,0.156 10 false *2 0.146,1.667 0.458,1.823 0.313,0.156 10 false *3 1.25,1.677 1.563,1.833 0.313,0.156 10 false *3 1.708,0.573 2.073,0.833 0.365,0.26 10 false (A)
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front Drive Shaft Damper RH
*3 Front Drive Shaft Damper Clamp


Install parts to the front drive outboard joint shaft assembly in the following order as shown in the illustration.

i.

New front drive shaft damper clamp


ii.

Front drive shaft damper RH


iii.

New front drive shaft damper clamp



b.

Set the dimension (A) as specified below.

Dimension (A):

434 to 438 mm (1.424 to 1.436 ft.)



c.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



d.

Install the 2 front drive shaft damper clamps to the front drive shaft damper RH.

NOTICE:

Be sure to install the clamp in the correct position.



e.
C304762

Using needle-nose pliers, engage the 2 claws to install the 2 front drive shaft damper clamps as shown in the illustration.


Hide 9.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY

a.
C287114C01
0.688,1.323 0.688,1.552 false 1.698,1.521 1.698,1.75 false 2.49,1.667 2.49,1.896 false 2.896,1.25 2.896,1.479 false 0.635,1.583 0.948,1.74 0.313,0.156 10 false *1 1.646,1.781 1.958,1.938 0.313,0.156 10 false *2 2.438,1.917 2.75,2.073 0.313,0.156 10 false *3 2.844,1.5 3.156,1.656 0.313,0.156 10 false *a
*1 Front Axle Inboard Joint Boot Clamp
*2 Front Axle Inboard Joint Boot
*3 Front No. 2 Axle Inboard Joint Boot Clamp
*a Protective Tape
V100135

Outboard joint side
V100136

Inboard joint side


Install new parts onto the front drive outboard joint shaft assembly in the following order:

i.

Front axle inboard joint boot clamp


ii.

Front axle inboard joint boot


iii.

Front No. 2 axle inboard joint boot clamp



b.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.

Remove the protective tape.


d.
C348433C02
1.76,1.5 2.26,2 2.26,2 1.271,1.844 false 2.292,1.917 2.604,2.073 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks and install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:

Face the serrated side of the tripod joint outward and install it to the outboard joint end.



e.

Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the areas where the rollers contact the tripod joint.

·

Keep the tripod joint free of foreign matter.

·

Make sure to install the tripod joint in the correct direction.




f.
C348431

Using a snap ring expander, install a new front drive inner shaft inner shaft snap ring to the front drive outboard joint shaft assembly.


g.

Pack the front drive inboard joint assembly and front axle inboard boot with grease.

Standard grease capacity:
for 8NR-FTS with 2WD:

130 to 150 g (4.59 to 5.29 oz.)

except 8NR-FTS with 2WD:

195 to 215 g (6.88 to 7.58 oz.)



h.
C348434

Install the 3 rollers to the tripod joint.

NOTICE:
·

Make sure to install the rollers in the correct direction as shown in the illustration.

·

Do not drop the rollers.




i.
F045461C09
1.979,0.656 1.979,0.271 1.979,0.271 1.333,0.271 false 1.646,0.969 1.646,0.271 false 1.146,0.177 1.365,0.417 0.219,0.24 10 false *a
*a Matchmark


Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.


Hide 10.INSPECT FRONT AXLE INBOARD JOINT BOOT (for 8NR-FTS)

a.

Install the front axle inboard joint boot to the front drive inboard joint assembly.


b.
C213153C03
0.101,0.042 0.290,0.213 0.190,0.171 10 *a 0.101,2.706 0.290,2.877 0.190,0.171 10 *b 1.489,1.453 1.714,1.626 0.226,0.173 10 (A) 1.505,3.766 1.731,3.939 0.226,0.173 10 (A)
*a LH Side and RH Side, 2WD
*b RH Side, AWD


Check whether each drive shaft dimension (A) is within specification.

Dimension (A):
Drive Type LH Side RH Side
for 2WD 611.8 mm (2.01 ft.) 877.5 mm (2.88 ft.)
for AWD 611.8 mm (2.01 ft.) 872.6 mm (2.86 ft.)



Hide 11.INSPECT FRONT AXLE INBOARD JOINT BOOT (for 3ZR-FAE)

a.

Install the front axle inboard joint boot to the front drive inboard joint assembly.


b.
C213153C03
0.101,0.042 0.290,0.213 0.190,0.171 10 *a 0.101,2.706 0.290,2.877 0.190,0.171 10 *b 1.489,1.453 1.714,1.626 0.226,0.173 10 (A) 1.505,3.766 1.731,3.939 0.226,0.173 10 (A)
*a LH Side
*b RH Side


Check whether each drive shaft dimension (A) is within specification.

Dimension (A):
LH Side RH Side
590.5 mm (1.94 ft.) 887.1 mm (2.91 ft.)



Hide 43448F 12.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the front axle inboard joint boot clamp onto the front axle inboard joint boot.


c.
C296175E01
1.74,1.396 2.104,1.708 2.104,1.708 2.729,1.708 true 2.781,1.625 3.24,1.823 0.458,0.198 10 false SST

Place SST onto the front axle inboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


d.

Tighten SST so that the front axle inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.

Remove SST.


f.
C195760E02
1.531,1.5 2.365,1.5 false 2.406,1.417 2.854,1.667 0.448,0.25 10 false SST

Using SST, measure the clearance of the front axle inboard joint boot clamp.

SST
09240-00020  

Clearance:

1.2 to 4.0 mm (0.05 to 0.16 in.)


If the clearance is outside the specified range, retighten SST.


Hide 43448G 13.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.

Install the front No. 2 axle inboard joint boot clamp onto the front axle inboard joint boot.


b.
C298539E01
0.677,1.625 1.521,1.625 1.521,1.625 2.146,1.125 true 0.385,1.542 0.844,1.74 0.458,0.198 10 false SST

Place SST onto the front No. 2 axle inboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


c.

Tighten SST so that the front No. 2 axle inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



d.

Remove SST.


e.
C086270E20
1.896,0.792 3.021,0.813 true 3.083,0.729 3.406,0.885 0.323,0.156 10 false SST

Using SST, measure the clearance of the front No. 2 axle inboard joint boot clamp.

SST
09240-00020  

Clearance:

1.2 to 4.0 mm (0.05 to 0.16 in.)


If the clearance is outside the specified range, retighten SST.