Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for TMC Made)
RM32H0E _52 Drivetrain _060137 DRIVE SHAFT / PROPELLER SHAFT _0294913 FRONT DRIVE SHAFT ASSEMBLY(for TMC Made) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for TMC Made)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL FRONT DRIVE SHAFT BEARING (for RH Side)

a.

for AWD:

i.
C092032E16
2.26,1.615 2.26,0.969 false 2.271,0.969 2.5,0.969 false 0.656,0.333 1.063,0.333 1.063,0.333 1.063,0.646 false 2.563,0.885 3.125,1.094 0.563,0.208 10 false SST 0.302,0.25 0.646,0.438 0.344,0.188 10 false SST

Using SST, install a new front drive shaft bearing.

SST
09527-10011  
09527-30010  

NOTICE:

The front drive shaft bearing should be completely installed.



ii.
C092033

Using a snap ring expander, install a new shaft snap ring.



Hide 41336E 2.INSTALL FRONT DRIVE SHAFT DUST COVER LH

a.
C157559C04
1.292,0.719 1.292,0.292 1.292,0.292 1.427,0.292 false 1.469,0.229 1.938,0.542 0.469,0.313 10 false *a
*a Steel Plate


Using a steel plate and a press, install a new front drive shaft dust cover LH.

NOTICE:
·

The dust cover should be completely installed.

·

Be careful not to damage the front drive shaft dust cover LH.

·

Install the front drive shaft dust cover LH in the correct direction.




Hide 41336D 3.INSTALL FRONT DRIVE SHAFT DUST COVER RH

a.

for 2WD:

i.

Perform the same procedure as for the LH side.



b.

for AWD:

i.
C305637C03
0.406,1.604 0.594,1.844 false 0.073,1.5 0.531,1.698 0.458,0.198 10 false SST 1.781,4.115 2.01,4.26 0.229,0.146 10 false (A)

Using SST and a press, install a new front drive shaft dust cover RH until the distance (A) from the tip of the center drive shaft to the front drive shaft dust cover RH meets the specification.

SST
09527-10011  

Distance (A):

102.1 to 103.1 mm (4.02 to 4.05 in.)


NOTICE:
·

The front drive shaft dust cover RH should be completely installed.

·

Be careful not to damage the front drive shaft dust cover RH.

·

Install the front drive shaft dust cover RH in the correct direction.





Hide 4.INSTALL FRONT AXLE OUTBOARD JOINT BOOT

a.
C295108C01
1.979,0.75 2.313,1.042 false 2.344,0.948 2.656,1.104 0.313,0.156 10 false *a
*a Protective Tape


Wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


b.
C295107C01
1.365,1.708 1.365,1.896 false 1.99,1.75 1.99,1.917 false 2.542,1.646 2.542,1.885 false 3.094,1.49 3.094,1.896 false 1.292,1.927 1.604,2.083 0.313,0.156 10 false *1 1.906,1.927 2.219,2.083 0.313,0.156 10 false *2 2.469,1.917 2.781,2.073 0.313,0.156 10 false *3 3.031,1.917 3.344,2.073 0.313,0.156 10 false *4
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front No. 2 Axle Outboard Joint Boot Clamp
*3 Front Axle Outboard Joint Boot
*4 Front Axle Outboard Joint Boot Clamp
V100135

Outboard joint side
V100136

Inboard joint side


Install new parts onto the front drive outboard joint shaft assembly in the following order:

i.

Front No. 2 axle outboard joint boot clamp


ii.

Front axle outboard joint boot


iii.

Front axle outboard joint boot clamp



c.

Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.

Standard grease capacity:

135 to 145 g (4.77 to 5.11 oz.)



d.

Install the front axle outboard joint boot into the front drive outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the front axle outboard joint boot.

·

Keep the inside of the front axle outboard joint boot free of foreign matter.




Hide 43447F 5.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

CAUTION:
·
C331975

When installing the front No. 2 axle outboard joint boot clamp, do not perform the work without wearing protective gloves.

·

If work is performed without using protective gloves, injuries may occur.



a.
C415871C01
2.156,1.5 2.677,1.5 false 0.833,1.24 1.354,1.24 false 1.917,2.031 2.438,2.031 false 2.708,1.438 3.021,1.594 0.313,0.156 10 false *a 0.667,1.177 0.979,1.333 0.313,0.156 10 false *b 1.729,1.948 2.042,2.104 0.313,0.156 10 false *c
*a Fulcrum Point
*b Lever Push Position
*c Band Support Position


Install the front No. 2 axle outboard joint boot clamp to the front axle outboard joint boot and temporarily fold back the lever at the fulcrum point.

NOTICE:
·

Set the lever to the guide groove correctly and install the clamp as far to the inside of the vehicle as possible.

·

Check the band and the lever for any deformation before folding back the lever.

·

The lever folds easily at the fulcrum point when pushed at the position shown in the illustration.

·

When folding back the lever, do not push at the end of the lever.

C415873C01
6.771,1.49 6.125,1.49 true 5.948,1.417 6.26,1.573 0.313,0.156 10 false *a
*a Temporary Claw - -


·

If the lever bends in the middle, it may not engage with the temporary claws or may not be held in the correct position.




b.

As shown in the illustration, while pressing the outboard joint area against the work surface, firmly press the lever into place by rolling the outboard joint area forward from the folded fulcrum point to the temporary claw area until a click sound is heard.

C415872C01
3.604,1.052 3.135,1.406 3.135,1.406 3.708,1.042 true 2.083,1.49 1.594,1.49 true 1.958,2.281 1.688,2.281 1.688,2.281 1.448,1.906 true 5.927,2.229 5.646,1.938 5.646,1.938 5.49,1.938 true 3.823,0.292 4.135,0.448 0.313,0.156 10 false *a 4.104,1.302 4.417,1.458 0.313,0.156 10 false *b 5.24,0.583 5.552,0.74 0.313,0.156 10 false *c 2.979,1.354 3.292,1.51 0.313,0.156 10 false *d 1.208,2.365 1.521,2.521 0.313,0.156 10 false *b 1.427,1.417 1.74,1.573 0.313,0.156 10 false *d 2.01,2.219 2.323,2.375 0.313,0.156 10 false *e 5.281,1.875 5.594,2.031 0.313,0.156 10 false *d
*a Press down *b Contact Point
*c Roll forward *d Temporary Claw
*e Fulcrum Point - -


NOTICE:
·

Do not damage the deflector.

·

Make sure that the outboard joint is in direct contact with the work surface.




c.
C265825C09
1.698,3.74 1.135,4.417 1.135,4.417 1.896,3.771 true 0.979,4.406 1.292,4.604 0.313,0.198 10 false *a
*a Buckle


Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:
·

Do not use excessive force when tapping with the plastic hammer.

·

Do not damage the front axle outboard joint boot.




Hide 43447E 6.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

CAUTION:
·
C331975

When installing the front axle outboard joint boot clamp, do not perform the work without wearing protective gloves.

·

If work is performed without using protective gloves, injuries may occur.



a.
C107948

Install the front axle outboard joint boot clamp to the front axle outboard joint boot and provisionally bend the lever.

NOTICE:
·

Set the lever into the guide groove correctly.

·

Check the band and lever for any deformation before bending the lever.




b.
C112271C01
2.292,1.854 2.344,1.396 false 2.229,1.854 2.542,2.01 0.313,0.156 10 false *a
*a Place the tip near the center of the lever


Using water pump pliers, pinch the front axle outboard joint boot clamp to provisionally fix it.


c.
C295110

Using a plastic hammer, tap the buckle to fix it while adjusting the clearance between the lever and groove to make the clearances between the buckle edge and lever end even.

NOTICE:

Do not damage the front axle outboard joint boot.



Hide 43474E 7.INSTALL FRONT DRIVE SHAFT DAMPER LH

a.
C354588C09
0.198,1.292 0.198,1.552 false 0.802,1.333 0.802,1.594 false 1.385,1.281 1.385,1.542 false 2.24,1.448 2.24,1.708 false 1.479,0.594 1.938,0.792 0.458,0.198 10 false (A) 2.188,1.719 2.5,1.875 0.313,0.156 10 false *1 0.729,1.615 1.042,1.771 0.313,0.156 10 false *2 1.323,1.563 1.635,1.719 0.313,0.156 10 false *3 0.146,1.573 0.458,1.729 0.313,0.156 10 false *3
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front Drive Shaft Damper LH
*3 Front Drive Shaft Damper Clamp


Install parts to the front drive outboard joint shaft assembly in the following order as shown in the illustration.

i.

New front drive shaft damper clamp


ii.

Front drive shaft damper LH


iii.

New front drive shaft damper clamp



b.

Set the dimension (A) as specified below.

Dimension (A):

211.7 to 215.7 mm (8.34 to 8.49 in.)



c.

Hold the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



d.

Install the 2 front drive shaft damper clamps to the front drive shaft damper LH.

NOTICE:

Be sure to install the clamp in the correct position.



e.
C304762

Using needle-nose pliers, engage the 2 claws to install the 2 front drive shaft damper clamps as shown in the illustration.


Hide 43474D 8.INSTALL FRONT DRIVE SHAFT DAMPER RH (for 2WD)

a.
C354589C07
2.26,1.813 2.26,1.479 false 1.333,1.625 1.333,1.292 false 0.219,1.625 0.219,1.292 false 0.74,1.729 0.74,1.396 false 1.51,0.594 1.823,0.792 0.313,0.198 10 false (A) 2.177,1.875 2.49,2.031 0.313,0.156 10 false *1 0.656,1.781 0.969,1.938 0.313,0.156 10 false *2 1.26,1.688 1.573,1.844 0.313,0.156 10 false *3 0.146,1.677 0.458,1.833 0.313,0.156 10 false *3
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front Drive Shaft Damper RH
*3 Front Drive Shaft Damper Clamp


Install parts to the front drive outboard joint shaft assembly in the following order as shown in the illustration.

i.

New front drive shaft damper clamp


ii.

Front drive shaft damper RH


iii.

New front drive shaft damper clamp



b.

Set the dimension (A) as specified below.

Dimension (A):

488 to 492 mm (1.60 to 1.61 ft.)



c.

Hold the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



d.

Install the 2 front drive shaft damper clamps to the front drive shaft damper RH.

NOTICE:

Be sure to install the clamp in the correct position.



e.
C304762

Using needle-nose pliers, engage the 2 claws to install the 2 front drive shaft damper clamps as shown in the illustration.


Hide 43030 9.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY

a.
C286840C01
0.75,1.667 0.75,1.323 false 1.354,1.802 1.354,1.458 false 2.5,1.958 2.5,1.615 false 2.917,1.594 2.917,1.25 false 0.667,1.677 0.979,1.833 0.313,0.156 10 false *1 1.281,1.823 1.594,1.979 0.313,0.156 10 false *2 2.417,1.99 2.729,2.146 0.313,0.156 10 false *3 2.833,1.604 3.146,1.76 0.313,0.156 10 false *a
*1 Front Axle Inboard Joint Boot Clamp
*2 Front Axle Inboard Joint Boot
*3 Front No. 2 Axle Inboard Joint Boot Clamp
*a Protective Tape
V100135

Outboard joint side
V100136

Inboard joint side


Install new parts to the front drive outboard joint shaft assembly in the following order:

i.

Front axle inboard joint boot clamp


ii.

Front axle inboard joint boot


iii.

Front No. 2 axle inboard joint boot clamp



b.

Hold the front drive outboard joint shaft assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.

Remove the protective tape.


d.
C295111C01
1.458,1.625 2.146,1.917 2.146,1.917 1.938,1.385 true 2.219,1.854 2.531,2.01 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks and install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:

Face the serrated side of the tripod joint outward and install it to the front drive outboard joint shaft assembly end.



e.

Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Keep the tripod joint free of foreign matter.




f.
C295102

Using a snap ring expander, install a new front drive inner shaft inner shaft snap ring to the front drive outboard joint shaft assembly.


g.

Pack the front drive inboard joint assembly and front axle inboard joint boot with grease.

Standard grease capacity:

168 to 178 g (5.93 to 6.28 oz.)



h.
C160686C04
1.719,1.375 2.094,1.156 true 2.135,1.063 2.344,1.281 0.208,0.219 10 false *a
*a Groove


Install a new front axle inboard joint grommet to the front drive inboard joint assembly.

NOTICE:
·

Align the phase of the protrusions and depressions, and assemble the front axle inboard joint grommet to the front drive inboard joint assembly.

·

Make sure the protrusion on the inner corner of the front axle inboard joint grommet is securely inserted into the groove in the outer surface of the joint.




i.
C158439C18
1.385,1.24 1.125,0.458 1.125,0.458 1.927,0.667 true 0.948,0.365 1.344,0.521 0.396,0.156 10 *a
*a Matchmark


Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.


Hide 10.INSTALL FRONT AXLE INBOARD JOINT BOOT

a.

Install the front axle inboard joint boot to the front drive inboard joint assembly.

NOTICE:
·

Keep the inside of the front drive shaft inboard joint boot free of foreign matter.

·

Keep the grooves free of grease.




Hide 43448F 11.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

CAUTION:
C331975

·

When installing the front axle inboard joint boot clamp, do not perform the procedure without wearing protective gloves.

·

Performing the procedure without wearing protective gloves could result in injury.



a.
C107948

Install the front axle inboard joint boot clamp to the front axle inboard joint boot and temporarily fold back the lever.

NOTICE:
·

Set the lever into the guide groove correctly.

·

Check the band and the lever for any deformation before folding back the lever.




b.
C158356C01
2.469,0.938 2.771,1.219 0.302,0.281 10 false *a
*a Place the tip near the center of the lever


Using water pump pliers, pinch the front axle inboard joint boot clamp to temporarily secure it.


c.
C264475

Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:

Do not damage the front axle inboard joint boot.



Hide 43448G 12.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

CAUTION:
C331975

·

When installing the front No. 2 axle inboard joint boot clamp, do not perform the procedure without wearing protective gloves.

·

Performing the procedure without wearing protective gloves could result in injury.



a.

Install the front No. 2 axle inboard joint boot clamp to the drive shaft inboard joint boot groove.


b.
C193645N05
1.458,1.531 1.698,1.865 0.24,0.333 10 (A)

Check whether the dimension (A) of each drive shaft is within specification.

Dimension (A):
LH Side 615.9 mm (2.02 ft.)
RH Side (for 2WD) 870.9 mm (2.86 ft.)
RH Side (for AWD) 876.5 mm (2.88 ft.)



c.

While holding dimension (A) to the specified length, pull the indented portion of the inboard joint grommet outward with your finger, etc. to release air from inside the inboard joint and equalize the air pressure with the atmospheric pressure.


d.
C268393C02
1.917,1.292 2.292,1.052 false 2.26,2.781 2.635,2.542 true 2.365,0.896 2.677,1.094 0.313,0.198 10 false *a 1.688,2 1.844,2.198 0.156,0.198 10 false A 2.688,3.708 2.844,3.906 0.156,0.198 10 false A 0.677,3.708 0.833,3.906 0.156,0.198 10 false A 2.656,2.406 2.969,2.604 0.313,0.198 10 false *b
*a Support Point
*b Indented Portion


Set the folding support point of the clamp so that it is aligned with any of the A portions indicated by arrows in the illustration.


e.
C415869C01
2.156,1.542 2.656,1.542 false 0.781,1.135 1.281,1.135 false 1.979,2.073 2.479,2.073 false 2.708,1.469 3.021,1.625 0.313,0.156 10 false *a 0.615,1.063 0.927,1.219 0.313,0.156 10 false *b 1.792,1.99 2.104,2.146 0.313,0.156 10 false *c
*a Fulcrum Point
*b Lever Push Position
*c Band Support Position


Temporarily fold back the lever at the fulcrum point.

NOTICE:
·

Check the band and the lever for any deformation before folding back the lever.

·

The lever folds easily at the fulcrum point when pushed at the position shown in the illustration.

·

When folding back the lever, do not push at the end of the lever.

C415873C01
6.771,1.49 6.125,1.49 true 5.948,1.417 6.26,1.573 0.313,0.156 10 false *a
*a Temporary Claw - -


·

If the lever bends in the middle, it may not engage with the temporary claws or may not be held in the correct position.




f.

As shown in the illustration, while pressing the inboard joint area against the work surface, firmly press the lever into place by rolling the inboard joint area forward from the folded fulcrum point to the temporary claw area until a click sound is heard.

C415870C01
3.615,1.104 3.365,1.698 3.365,1.698 3.719,1.083 true 2.083,1.49 1.594,1.49 true 5.927,2.219 5.76,1.917 5.76,1.917 5.531,1.917 true 1.885,2.292 1.604,2.292 1.604,2.292 1.365,1.875 true 3.823,0.302 4.135,0.458 0.313,0.156 10 false *a 4.073,1.333 4.385,1.49 0.313,0.156 10 false *b 5.219,0.698 5.531,0.854 0.313,0.156 10 false *c 3.25,1.719 3.563,1.875 0.313,0.156 10 false *d 1.208,2.365 1.521,2.521 0.313,0.156 10 false *b 1.427,1.406 1.74,1.563 0.313,0.156 10 false *d 5.354,1.844 5.667,2 0.313,0.156 10 false *d 1.938,2.25 2.25,2.406 0.313,0.156 10 false *e
*a Press down *b Contact Point
*c Roll forward *d Temporary Claw
*e Fulcrum Point - -


NOTICE:
·

Make sure that the inboard joint is in direct contact with the work surface.

·

Do not damage the front drive shaft dust cover.




g.
C158764C05
1.802,3.719 1.115,4.375 1.115,4.375 1.615,3.698 true 0.979,4.365 1.292,4.563 0.313,0.198 10 false *a
*a Buckle


Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:
·

Do not use excessive force when tapping with the plastic hammer.

·

Do not damage the front axle inboard joint boot.