Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C146E  Open in ABS Solenoid Relay Circuit  


DESCRIPTION

The ABS solenoid relay is built into the skid control ECU in the brake actuator assembly. The ABS solenoid relay supplies power to the ABS and TRC solenoids. The skid control ECU detects a solenoid relay malfunction by performing a self check and relay operation check.

DTC No. Detection Item DTC Detection Condition Trouble Area
C146E Open in ABS Solenoid Relay Circuit Either of the following is detected:
1.

A solenoid relay drive circuit in the skid control ECU is malfunctioning.

2.

The solenoid relay cannot be switched between on and off.


ABS solenoid relay (brake actuator assembly)

DTC Detection Conditions: C146E
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status A solenoid relay drive circuit in the skid control ECU is malfunctioning. ○ -
The solenoid relay cannot be switched between on and off. - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C334074E04
5.979,2.177 6.479,2.406 0.5,0.229 10 false SFRH 5.99,2.698 6.396,2.906 0.406,0.208 10 false SFLH 5.969,3.208 6.396,3.417 0.427,0.208 10 false SRRH 5.979,3.698 6.406,3.917 0.427,0.219 10 false SRLH 5.979,4.188 6.396,4.417 0.417,0.229 10 false SFRR 5.99,4.688 6.427,4.906 0.438,0.219 10 false SFLR 5.969,5.177 6.417,5.385 0.448,0.208 10 false SRRR 5.979,5.656 6.406,5.865 0.427,0.208 10 false SRLR 5.979,6.167 6.438,6.385 0.458,0.219 10 false SRM1 5.969,6.667 6.448,6.865 0.479,0.198 10 false SRM2 5.979,7.156 6.417,7.396 0.438,0.24 10 false SRC1 5.979,7.646 6.448,7.896 0.469,0.25 10 false SRC2 4.417,4.24 5.615,4.479 1.198,0.24 10 false Skid Control ECU 3.531,5.229 4.052,5.479 0.521,0.25 10 false GND1 3.24,4.958 3.521,5.188 0.281,0.229 10 false 46 4.323,8.25 4.656,8.458 0.333,0.208 10 false A42 4.313,8.406 5.979,8.656 1.667,0.25 10 false Brake Actuator Assembly 0.302,1.188 1.26,1.427 0.958,0.24 10 false from Battery 2.25,1.354 3.01,1.542 0.76,0.188 10 false ABS-MAIN 3.26,1.115 3.479,1.344 0.219,0.229 10 false 30 3.521,1.333 3.885,1.531 0.365,0.198 10 false +BS 4.542,1.052 5.51,1.448 0.969,0.396 10 false ABS Solenoid Relay

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.REPLACE BRAKE ACTUATOR ASSEMBLY
a.

Result:
Proceed to
NEXT



NEXT

END