Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for RHD) › 2016.10–2019.09
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0298589 BRAKE ACTUATOR(for RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the brake actuator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)*2 Stop and start system (Click here)
Replacement of brake actuator assembly Operate the electric parking brake switch assembly Parking brake indicator light (red) blinks when the ignition switch is first turned on (IG) (Click here)
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

*2: w/ Stop and start system

PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55737B 4.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 55735A 5.REMOVE WATER GUARD PLATE LH

Hide 55736D 6.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735C 7.REMOVE COWL BODY MOUNTING REINFORCEMENT RH

Hide 55701J 8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 9.REMOVE BATTERY

Hide 86510A 10.REMOVE SECURITY HORN ASSEMBLY (w/ Security Horn)

Hide 11.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 12.REMOVE BRAKE ACTUATOR WITH BRACKET

a.
C366925C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake actuator assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



b.
C366909

Using a 10 mm union nut wrench, disconnect the brake tube from the front flexible hose.


c.
C369565C01
1.24,1.792 1.375,1.448 true 1.917,1.271 2.469,1.427 true 1.875,0.875 2.438,0.74 true 1.646,0.927 2.083,0.458 true 0.667,1.125 1.063,1.125 true 0.677,0.792 1.302,1.042 true 1.125,1.844 1.385,2.042 0.26,0.198 10 true *a 2.521,1.365 2.75,1.615 0.229,0.25 10 true *b 2.469,0.615 2.698,0.823 0.229,0.208 10 true *c 2.125,0.344 2.365,0.531 0.24,0.188 10 true *d 0.438,0.688 0.646,0.896 0.208,0.208 10 true *e 0.427,1.052 0.656,1.24 0.229,0.188 10 true *f
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Use tags or make a memo to identify the places to reconnect the brake tubes.


d.
C366926

Using a 10 mm and 12 mm union nut wrench, disconnect the 6 brake tubes from the brake actuator assembly.


e.
C366928

Disengage the 2 clamps to separate the fuel main tube and fuel tank to canister tube from the No. 2 fuel tube clamp.


f.

Remove the bolt, 2 nuts and brake actuator with bracket from the vehicle body.

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not hold the brake actuator assembly by the connector.



HINT:

Remove the brake actuator with bracket while avoiding the brake tubes.



Hide 44510 13.REMOVE BRAKE ACTUATOR ASSEMBLY

a.
C366929

Loosen the 2 nuts.


b.

Remove the bolt and brake actuator assembly from the brake actuator bracket assembly.

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 44521A 14.REMOVE NO. 1 BRAKE ACTUATOR CASE COLLAR

a.
C366931

Remove the No. 1 brake actuator case collar from the brake actuator bracket cushion.


Hide 44547B 15.REMOVE BRAKE ACTUATOR BRACKET CUSHION

C366932

a.

Remove the brake actuator bracket cushion from the brake actuator bracket assembly.


Hide 77286D 16.REMOVE NO. 2 FUEL TUBE CLAMP

a.
C366930

Disengage the claw to remove the No. 2 fuel tube clamp from the brake actuator bracket assembly.